• 전기전자학회논문지
• /
• 제19권3호
• /
• pp.366-370
• /
• 2015

본 논문에서는 배터리 교대 방전 기법에서 배터리 셀의 방전 시간을 밸런싱함으로서 배터리 사용 시간을 크게 높이는 방법을 제안한다. 기존 기법에서는 다수의 배터리 셀을 교대로 방전시킴으로서 배터리에 회복 효과를 발생시키고, 이를 통해 배터리 사용 시간을 연장한다. 이때, 시스템에 공급되는 전원이 차단되지 않도록 배터리 셀이 동시에 켜지는 시간 구간이 있는데, 배터리 셀의 전압 차이로 인해 여러 가지 문제가 발생한다. 이러한 문제를 해결하기 위해서 배터리 셀이 가능한 한 균등한 전압을 가지도록 배터리의 방전 시간을 제어한다. 실험 결과, 제안하는 방법에서 배터리 사용 시간이 19.2% 연장되었다.

• Journal of Information Display
• /
• 제2권1호
• /
• pp.24-33
• /
• 2001

The characteristics of the reset and the address discharges of an alternating current Plasma Display Panel (ac PDP) were studied using 2-dimensional numerical discharge cell simulation. We investigated the wall charge variations during the reset discharge adopting ramping reset pulse and the subsequent addressing discharge. The roles of the ramping reset scheme can be divided into two stages, each electrode gathers wall charges during ramping-up of the initial stage and the built-up wall charges are lost during ramping-down of the later stage. Address discharge does not only change the wall charge distributions on the address and the scan electrodes but also on the sustain electrode. The increase in the wall charges on the sustain electrode was observed with the variation of the applied voltage to the sustain electrode during the address period. The increase of the applied voltage to the sustain electrode during the address period is expected to induce the decrease of the sustain voltage during the display period.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.503-506
• /
• 2004

In this paper, we suggest a new driving waveform for stable address discharge in AC PDP without the reduction of contrast ratio. To analyze the influence of cross-talk between discharge and non-discharge cells and verify that proposed waveform shows a stable address discharge, we measured the address discharge delay time. The proposed waveform shows the reduction of the cross-talk and concurrently the improvement of address voltage margin compared with those of selective reset waveform having one reset period in 1TV-Field..

• 전기전자학회논문지
• /
• 제18권1호
• /
• pp.96-105
• /
• 2014

본 논문에서는 배터리의 비선형적 방전 특성인 회복효과를 사용하여 배터리의 사용 시간을 연장하는 기법을 제안한다. 일반적으로 배터리의 사용 시간을 예측할 때에는 배터리 내부에 저장된 에너지가 일정하다고 가정하지만, 실제로는 배터리 내부의 화학 반응 때문에 배터리를 계속 방전시키지 않고 중간에 쉬는 시간을 만들어주면 더 많은 에너지를 끌어낼 수 있는데 이를 회복효과라 한다. 제안하는 기법에서는 다수의 배터리 셀을 교대로 방전시킴으로서 기기의 전력 공급은 그대로 유지하면서 배터리 셀 일부를 쉬게 하여 회복효과를 발생시키고, 이에 따라 배터리의 사용 시간을 연장시킬 수 있다. 실험 결과, 2개의 배터리 셀을 기존처럼 병렬 연결하여 방전시키는 것에 비해 배터리 셀을 교대로 방전시키면 배터리 사용시간이 약 7% 증가하였다.

• 전기학회논문지
• /
• 제56권3호
• /
• pp.577-582
• /
• 2007

The plasma display panel is an image expression display using gas discharge plasma. However, gas discharge characteristics vary with temperature as gas discharge is sensitive to temperature. The discharge time lag extends a lot in low temperature and it is known as the cause which hinders high speed addressing which is essential for the size enlargement of the panel. Accordingly this research aims at identifying the temperature-dependent discharge characteristic. The lower temperature becomes, the longer addressing discharge time lag becomes. Particularly the statistical time lag extends much in low temperature. The increasing of electric field shortens discharge time lag in low temperature. Also, when priming particles are sufficiently supplied, stable discharge can be performed regardless of the influence of temperature.

• 대한전기학회논문지
• /
• 제39권5호
• /
• pp.516-518
• /
• 1990

We have derived the equation which involves the variation of electron energy with time in a lowly ionized plasma when a low alternating electric field is applied. We consider only elastic collisions between electrons and neutral atoms. This equation is solved using the 4th-order Runge-Kutta method, and applied to argon gas discharge which is driven by source frequency of 100, 1K, 10K, 100K, and 1M (Hz). The results show that the variation of electron energy becomes flat with higher frequencies.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 C
• /
• pp.1060-1062
• /
• 1999

Pulsed Nd:YAG laser is used widely for materials processing and instrumentation. It is very important to control the laser energy density in materials processing by a pulsed Nd:YAG laser. A pulse repetition rate and a pulse width are regarded as the most dominant factors to control the energy density of laser beam. In this study, the alternating charge-discharge system was designed to adjust a pulse repetition rate. And the parallel mesh is added to increase laser output power. This system is controlled by one chip microprocessor and allows to replace an expensive condenser for high frequency to a cheap condenser for low frequency. In addition, we have investigated the current pulse shape of flashlamp and the operating characteristics of a pulsed Nd:YAG laser. As a result, it is found that the laser output of the power supply using the parallel mesh and the alternating charge-discharge system is not less than that of typical power supply. As the pulse repetition rate rises from 10pps to 110pps by the step of 20pps at 1000V and 1200V, it is found that the laser efficiency decreases but the laser output power increases about 5W at each step.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 E
• /
• pp.2204-2206
• /
• 1999

Pulsed Nd:YAC laser is used widely for materials processing and instrumentation. It is very important to control the laser energy density in materials processing by a pulsed Nd:YAG laser. A pulse repetition rate and a pulse width are regarded as the most dominant factors to control the energy density of laser beam. In this study, the alternating charge-discharge system was designed to adjust a pulse repetition rate. This system is controlled by one chip microprocessor and allows to replace an expensive condenser for high frequency to a cheap condenser for low frequency. In addition. we have investigated the current pulse shape of flashlamp and the operating characteristics of a pulsed Nd:YAG laser. As a result, it is found that the laser output of the power supply using the alternating charge-discharge system is not less than that of typical power supply. As the pulse repetition rate rises from 30pps to 120pps by the step of 30pps at 1200V, it is found that the laser efficiency decreases but the laser output power increases about 6W at each step.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제53권12호
• /
• pp.606-615
• /
• 2004

The discharge characteristics of a ramp reset waveform in the alternating current plasma display panel(ac PDP) were studied using a 2-dimensional numerical simulation. We analyzed the wall charge variation during the reset discharge, address discharge and sustain discharge adopting a ramp reset waveform. Then we investigated the principal parameters for a successful discharge. In this paper, we suggest a new parameter, printing particles' density and its effects on the stability of the ramp discharge. The maximum current flows of the three electrodes during the ramp reset period were decreased with the increase in the priming particles's density which was explained with the wall charge characteristics and the current flow characteristics obtained by a 2-D simulation.

• Transactions on Electrical and Electronic Materials
• /
• 제14권6호
• /
• pp.317-320
• /
• 2013

Partial discharge resistance for the epoxy systems with two diluents was investigated in the rod-plane electrodes arrangement, and the effect of electric frequency on the partial discharge resistance was also studied. Diglycidyl ether of bisphenol A (DGEBA) type epoxy was used as a base resin, and 1,4-butanediol diglycidyl ether (BDGE) or polyglycol (PG) as a reactive diluent was introduced to the DGEBA system, in order to decrease the viscosity of the DGEBA epoxy system. BDGE was acted as a chain extender, and PG acted as a flexibilizer, after the curing reaction. To measure the partial discharge resistance, 5 kV alternating current (ac) with three different frequencies (60, 500 and 1,000 Hz) was applied to the specimen in a rod-plane electrode arrangement, at $30^{\circ}C$. PG had a good effect, while BDGE had a bad effect on the partial discharge resistance of the DGEBA system, regardless of the electric frequency.