• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.33-39
• /
• 1999

This study was conducted to confirm the effect of bypass dust on the hydration and mechanical properties of the cement pastes and mortar obtained from ordinary Portland cement (OPC), OPC-slag and OPC-fly ash system. The rate of heat evolution is accelerated with the content of By-pass Dust(BD). total heat evolution increased because alkali-chlorides activated the hydration of blended cement. Compressive strength and bound water content show maximum value at 5wt% By-pass Dust(BD) on each curing time in ordinary Portland cement and slag blended cement. Ca(OH)2 content of Ordinary Portland Cement increased as the content of BD and curing time. In blended cement, the formation of Ca(OH)2 is active at early hydration stage. By pozzolanic reaction, the content of Ca(OH)2 is decreased as curing time goes by. According to the BD content stable chlorides complex of Friedel's salt (C3A·CaCl2·10H2O) is created. Due to the hydration activation effect of chlorides and alkali we observed Type II C-S-H, which developed into densest microstructure.

• Journal of the Korea Concrete Institute
• /
• v.25 no.3
• /
• pp.305-312
• /
• 2013

This paper reports the results of an investigation into the effects of silica fume on strength properties of alkali-activated slag cement (AASC) with water-binder (W/B) ratio and replacement ratio of silica fume content. The W/B ratio varied between 0.50 and 0.60 at a constant increment of 0.05. The silica fume content varied from 0% to 50% by weight of slag. The activators was used sodium hydroxide (NaOH) and the dosage of activator was 3M. The strength development with W/B ratio has been studied at different ages of 1, 3, 7 and 28 days. For mixes of AASC mortars with varying silica fume content, the flow values were lower than the control mixes (without silica fume). The flow value was decrease as the content of silica fume increase. This is because the higher surface areas of silica fume particles increase the water requirement. The analysis of these results indicates that, increasing the silica fume content in AASC mortar also increased the compressive strength. Moreover, the strength decreases with the W/B ratios increases. This is because the particle sizes of silica fume are smaller than slag. The high compressive strength of blended slag-silica fume mortars was due to both the filler effect and the activated reaction of silica fume evidently giving the mortar matrix a denser microstructure, thereby resulting in a significant gain in strength.

• The Journal of the Petrological Society of Korea
• /
• v.26 no.3
• /
• pp.183-200
• /
• 2017

Alkali rhyolites in the Cheonmunbong of the Mt. Baekdu stratovolcano show porphyritic texture in the glassy or aphanic groundmass. Major phenocryst is alkali-feldspar, pyroxene, and amphibole, and small amount of microphenocryst is olivine, quartz, opaque mineral (ilmenite). The content of $Fe^{2+}/(Fe^{2+}+Mg^{2+})$ and alkali elements in the mafic minerals is high. Alkali feldspar is classified as sanidine or anorthclase, olivine as fayalite, and pyroxene as ferro-hedenbergite of ferro-augite area. Amphibole belongs to alkali amphibole group, but FeO and $Fe_2O_3$ were not separated, so it is required future studies. Nb(-) anomaly suggesting that slab-derived materials might have played a primary role in the genesis of the rhyolite magma, is not observed. It is noted that they originated in the within plate environment which is not related to subduction zone of the convergent plate boundary. The Mt. Baekdu alkaline rocks are classified into the comendite series. The alkali rhyolites of the summit at Mt. Baekdu shows the disequilibrium mineral assemblages, suggesting that it evolved from thrachytic magma with experience of magma mixing as well as fractional crystallization.

• International Journal of Concrete Structures and Materials
• /
• v.5 no.2
• /
• pp.125-131
• /
• 2011

Five all-lightweight alkali-activated (AA) slag concrete mixes were tested according to the variation of water content to examine the significance and limitation on the development of cementless structural concrete using lightweight aggregates. The compressive strength development rate and shrinkage strain measured from the concrete specimens were compared with empirical models proposed by ACI 209 and EC 2 for portland cement normal weight concrete. Splitting tensile strength, and moduli of elasticity and rupture were recorded and compared with design equations specified in ACI 318-08 or EC 2, and a database compiled from the present study for ordinary portland cement (OPC) lightweight concrete, wherever possible. Test results showed that the slump loss of lightweight AA slag concrete decreased with the increase of water content. In addition, the compressive strength development and different mechanical properties of lightweight AA slag concrete were comparable with those of OPC lightweight concrete and conservative comparing with predictions obtained from code provisions. Therefore, it can be proposed that the lightweight AA slag concrete is practically applicable as an environmental-friendly structural concrete.

• Advances in materials Research
• /
• v.4 no.3
• /
• pp.133-144
• /
• 2015

The aim of this investigation is to prepare geopolymer resin by alkali activation of ceramic waste (AACW) with different sodium hydroxide (NaOH) and liquid sodium silicate (LSS) concentrations. In order to prepare geopolymer cement, AACW was replaced by 10 and 30 % by weight (wt.,) of concrete waste (CoW) as well as 10 and 30 wt., % ground granulated blast-furnace slag (GGBFS). The results showed that, the compressive strength of AACW increases with the increase of activator content up to 15:15 wt., % NaOH: LSS. All AACW hardened specimens activated by 3:3 (MC6), 6:6 (MC12), 12:12 (MC24) and 15:15 wt., % (MC30) NaOH: LSS destroyed when cured in water for 24h. The MC18 mix showed higher resistivity to water curing. The results also showed that, the replacement of AACW containing 9:9 wt., % NaOH: LSS (MC18) by 10 (MCCo10) and 30 (MCCo30) wt., % CoWdecreased the compressive strength at all ages of curing. In contrast, the MCCo10 mix showed the lower chemically combined water content compared to MC18 mix. The MCCo30 mix showed the higher chemically combined water content compared to MC18 and MCCo10 mixes. The compressive strength and chemically combined water of all AACWmixes containing GGBFS (MCS10 and MCS30) were higher than those of AACWwith no GGBFS (MC18). As the amount of GGBFS content increases the chemically combined water increases. The x-ray diffraction (XRD) proved that as the amount of CoWcontent increases, the degree of crystallinity increases. Conversely, the replacement of AACW by GGBFS leads to increase the amorphiticity character. The infrared spectroscopy (FTIR) confirms the higher reactivity of GGBFS compared to CoW as a result of successive hydration products formation, enhancing the compaction of microstructure as observed in scanning electron microscopy (SEM).

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.3
• /
• pp.199-206
• /
• 2018

Due to the advantages of less raw materials and fossil fuel consumption, lower carbon footprint, and the capability of pavement performance improvement, the recycling technology of asphalt is developed and applied for road rehabilitation and construction in the western countries over the past two decades. Cold recycled asphalt mixtures are bituminous materials normally made by mixing recycled aggregate from wasted asphalt with an asphalt emulsion and water at room temperature. This paper aims at investigating the properties of cold recycled asphalt mixture with alkali-activated filler according to wasted asphalt aggregate content. As a result, as the content of wasted asphalt aggregate increased, the marshall stability of cold recycled asphalt mixture decreased and void ratio increased. Also, grading curves for cold recycled asphalt mixture as specified in GR criteria were satisfied in all aggregate mixing conditions regardless of the wasted asphalt aggregate content.

• Journal of Korean Ophthalmic Optics Society
• /
• v.1 no.1
• /
• pp.1-14
• /
• 1996

The mixed alkali silicate glasses doped 0.1 mol% $Fe_2O_3$ are fabricated for studying the effect of transition metal oxides, which is related to the $Li^-$ ion movement in Magic-Angle-Spinning NMR. We have investigated the spin-lattice relaxation times in the room temperature and measured the $^7Li$ MAS-NMR spectrum with temperature. When the $Fe_2O_3$ oxides are added in alkali silicate glasses, the width of spectrum is changed a little but the line shape is hardly varied. For this reason, we can think that the mixed alkali effects are shown sufficiently in the spin-spin relaxation processes. However, it is not mixed alkali effects in this case. The activation energy of $Li^-$ ions are diminished in mixed alkali glasses. From the analysis of $Li^-$ diffusion environment, spin-lattice relaxation time and the nuclear magnetization, it is confirmed that the alkali mixed effects are not shown in $^7Li$ spin-lattice relaxation processes.

• Journal of the Korea Institute of Building Construction
• /
• v.17 no.3
• /
• pp.261-268
• /
• 2017

Red mud is an inorganic by-product obtained from the mineral processing of alumina from Bauxite ores. A highly alkali inorganic waste product with a pH level over 11, red mud in its original state negatively impacts the ecosystem, so appropriate treatment is necessary. The development of alkali activated slag-red mud cement can be a representative study aimed at recycling the strong alkali of the red mud as a construction material. However, Alkali-activated binders that use sodium activators have been reported to be more vulnerable to efflorescence. Therefore, in this study, the compressive strength, pore characteristics, water absorption, elution characteristics, and efflorescence properties of alkali-activated slag cement mortar were assessed according to their red mud substitution ratio.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.33 no.3
• /
• pp.75-83
• /
• 2001

The potential of oxygen delignification is a powerful tool to reduce detrimental environmental effects. This study was performed to investigate the effect of steam explosion treatment of chemically treated oak wood on oxygen-alkali pulping. Pulp yield during steam explosion treatment by ${Na_2}{O_3}$-NaOH impregnation was higher than the other impregnation chemicals. Also, NaOH extraction at room temperature after steam explosion treatment improved the kappa number from 140~116 to 90~64. Oxygen-alkali pulping of chemical steam explosion treated woods affected to pulp yields. ${Na_2}{O_3}$-NaOH impregnation was very effective to higher carbohydrate yields at same delignification level. Its carbohydrate yield seemed to be highly related to the effluent pH. Oxygen-alkali pulping after steam explosion treatment of ${Na_2}{O_3}$-NaOH impregnated wood was shown that carbohydrate yield was very high because its effluent pH was increase from natural to mild alkali. Even if oxygen bleaching limit the delignification to 50% in order to avoid unacceptable yield and viscosity losses, oxygen-alkali pulping after steam explosion by ${Na_2}{O_3}$-NaOH impregnation was possible to extend the delignification more than 80%. Considering high pulp yield with lower lignin content from steam explosion treated wood, it might be profitable to end the cook at a high kappa number instead of a low kappa number, and continuously apply the oxygen delignification, in order to better quality pulp.

• Journal of Fisheries and Marine Sciences Education
• /
• v.29 no.1
• /
• pp.108-117
• /
• 2017

Laver, Porphyra, is distinctive for its high content of proteins and polysaccharides such as porphyran and hemicellulose. The chemical properties of the polysaccharides extracted with different extraction methods such as hot water, dilute acid(pH 4.0) or alkali solution(2N NaOH) were examined to investigate the suitable extraction conditions for porphyran and hemicellulose from laver. For porphyran extraction, dilute acid solution was more preferable to hot water and alkali solution because of its higher 3,6-anhydrogalactose content and lower protein content. However, alkali solution was more suitable to extract the hemicellulose because of higher mannose content indicating the extraction of mannan. To decrease contamination of the polysaccharides with protein, the dried lavers were pretreated with enzymes (Protamex, Flavourzyme, Alcalase, Viscozyme) before hot water extraction. All enzyme pretreatments increased the yield of polysaccharides by compared with control (enzyme unpretreated) and Flavourzyme pretreatment was most effective to decrease protein contamination in the polysaccharide. All viscosities of porphyran solutions pretreated by enzymes were lower compared to the control porphyran solution and showed pseudoplastic behavior with yield stress. In case of alkali extraction of residues obtained after enzyme hydrolysis and hot water extraction, protease pretreatment increased the mannose contents in the polysaccharide while the xylose content was increased by Viscozyme pretreatment.