• Journal of Aerospace System Engineering
• /
• v.1 no.2
• /
• pp.27-36
• /
• 2007

The Damage Tolerant Design is developed to help alleviate structural failure and cracking problems in aerospace structures. Recently, the Damage Tolerant Design is required and recommended for most of aircraft design. In this paper, the damage tolerant design is applied to tilt rotor UAV. First of all, the fatigue load spectrum for the tilt rotor UAV is developed and fatigue analysis is performed for the flaperon joint which has FCL (fatigue critical location). Tilt rotor UAV has two modes: helicopter mode when UAV is taking off and landing; fixed wing mode when the tilt rotor UAV is cruising. To make fatigue load spectrum, FELIX is used for helicopter mode. TWIST is used for fixed wing mode. Fatigue analysis of flaperon joint is performed using fatigue load spectrum. E-N curve approach is used for picking crack initiation point. The LEFM(Linear Elastic Fracture Method) is considered for analyzing crack growth or propagation. Finally, including the crack initiation and propagation, the fatigue life is evaluated. Therefore the Damage Tolerant Design can be done.

• Proceeding of EDISON Challenge
• /
• 2016.03a
• /
• pp.203-208
• /
• 2016

In this paper, vibration characteristics in terms of the airfoil cross-sectional shape was examined by using the EDISON co-rotational plane beam-transient analysis. Assuming aircraft wing as a cantilevered beam with a constant cross-sectional shape, natural frequencies of each airfoil shape was compared while varying airfoil maximum thickness and maximum camber length, using Fast Fourier Transformation(FFT). When the airfoil maximum thickness was varied, natural frequency showed peak value at 18% chord, and decreased afterwards. When the airfoil maximum camber length was varied, natural frequency either increased or decreased at 6% chord, while at 8% the natural frequency showed its maximum. Applying such trends to B-737 wing airfoil, an improved B-737_mod airfoil shape was obtained with regard to the vibration characteristics.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.10
• /
• pp.669-676
• /
• 2022

In this paper, the carriage load analyses of stores installed on aircraft are conducted to validate the chimera grid method applied to an unstructured CFD solver, UMSAPv. First, the chimera grid method of UMSAPv is verified for the well-known Eglin Wing/Pylon/Finned store problem. Next, an angle of attack sweep of F/A-18C clean configuration is conducted at a subsonic speed. The computed results are compared with the results of the previous study using MSAPv, a structured CFD solver, to show the validity of Umsapv. Finally, the carriage of F/A-18C JDAM is carried out with a chimera grid as well as a single block grid. The computed results are compared with other computational, experimental and the flight tests.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.14 no.2
• /
• pp.222-231
• /
• 2011

In this paper, we have proposed a method which can make it possible to stably transmit and receive data like the ARC-164 radio frequency hopping environment as a S/W packet modem with PSK modulation. This is a method that the S/W packet modem with PSK digital modulation and the use of PC sound cards change over from data to voice signals and then transmit/receive data. We confirmed not only that it is possible to solve the slow speed communication with the use of sending data through multi-channels and PSK modulation that has the ability to methodically improve transmission rates, but also that it is possible to send the state of frequency hopping stably. In conclusion, we've confirmed both tactical values that though the transmission rate may be a tad slow, a state of frequency hopping of more than 94% confidence plus voice and data can be sent via radio at the same time. In this paper, the proposed S/W packet modem is only an implemented S/W component, so when we apply it to aircraft that we don't consider EMC problems with, then we have the advantage of a wider use of conventional UHF/VHF/HF radio that is possible to voice communication. If we recognize these operational requirements, we can apply for a lot of field equipment efficiently.

• Journal of Aerospace System Engineering
• /
• v.16 no.1
• /
• pp.97-103
• /
• 2022

An aircraft component can only be mounted on an aircraft if it has been certified to have a structural robustness under flight load conditions. Among the major components of the aircraft, a pylon is a structure that connects external equipment such as an engine, and external attachments with the main wing of an aircraft and transmits the loads acting on it to the main structure of the aircraft. In civil aircraft, when there is an incident of fire in the engine area, the pylon prevents the fire from spreading to the wings. This study presents the results of structural static tests performed to verify the structural robustness of a fuel pylon used to mount external fuel tank in an aircraft. In the main text, we present the test set-up diagram consisting of test fixture, hydraulic pressure unit, load control system, and data acquisition equipment used in the structure static test of the fuel pylon. In addition, we introduce the software that controls the load actuator, and provide a test profile for each test load condition. As a result of the structural static test, it was found that the load actuator was properly controlled within the allowable error range in each test, and the reliability of the numerical analysis was verified by comparing the numerical analysis results and the strain obtained from the structural test at the main positions of the test specimen. In conclusion, it was proved that the fuel pylon covered in this study has sufficient structural strength for the required load conditions through structural static tests.

• Journal of Convergence for Information Technology
• /
• v.11 no.4
• /
• pp.26-34
• /
• 2021

In the era of the Fourth Industrial Revolution, the future battlefield will carry out multi-area operations with hyper-connected, high-speed and mobile systems. In order to prepare for changes in the future, the Korean military intends to develop various weapons systems and form a multi-layer tactical network to support On The Move communication. However, current tactical networks are limited in support of On The Move communications. In other words, the operation of multi-beam antennas is necessary to efficiently construct a multi-layer tactical network in future warfare. Therefore, in this paper, we look at the need for multi-beam antennas through the operational scenario of a multi-layer tactical network. In addition, based on development consideration factors, features of rotary-wing and fixed-wing aircraft, we present the location and operation of airborne relay drone installations of multi-beam antennas.

• Aerospace Engineering and Technology
• /
• v.4 no.1
• /
• pp.1-8
• /
• 2005

Civil aviation regulation such as FAR and loads analysis procedure based on this was explained, and loads analysis procedure and results for Smart UAV was presented for application case. For loads analysis, applicable regulations and loads conditions should be prepared in advance, and modeling for aerodynamics, weight, and structure should be performed. Panel method is usually adopted for aircraft loads analysis to obtain aerodynamic loads. In this study, ARGON which is multidisciplinary fixed wing aircraft design software co-developed by KARI and TsAGI was used for loads analysis. ARGON can be utilized for flutter and stress analysis as well as for flight and ground loads analysis. In this paper, flight loads analysis of 4-seater canard airplane was performed with ARGON and that results were presented.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.5 no.1
• /
• pp.65-79
• /
• 1997

In this study, we deviced side warning system that is necessary to the ground operation of aircraft. The system consist of obstacle detection part, transmission part, receive part, and warning part. We used TOF(Time Of Flight) method using 40kHz ultrasonic wave as the obstacle detection part. The 447MHz RF module was applied to the transmission and receive part. The warning part is activated by the computer using received distance data. The detection system attach to the left/right side edge of main wing and horizontal stabilizer. We have decided 10m obstacle detection range. The result of experiment was satisfactory.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.19 no.2
• /
• pp.1-9
• /
• 2011

Several studies on the development for solar powered uninhabited aerial vehicles(UAVs) are under way as the use of the renewable energy becomes more and more important these days. This paper is for the conceptual design by a discrete and iterative method. An initial design point with 1.5 meter wing span is determined in the global design, which deploys the mass and energy balances among each component of UAV including solar cells and airframe. Then, the iteration for subsystems is carried out with the help of Vortex Lattice Method(VLM) to optimize the aircraft configuration and the solar power system. It is demonstrated in simulations that the optimized design increases the flight time from 62 to 120 minutes when the solar power system is installed. Also, the associated dynamic analysis reveals that the designed small aircraft has the acceptable stability and controllability.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.5
• /
• pp.46-55
• /
• 2006

In general, 3-dimensional point-mass equation has been widely used for the trajectory optimization of the fixed-wing aircraft and reentry vehicle. But it should be modified and represent target vehicle's own characteristics. For a lighter-than-air vehicle such as an airship, there exists different and peculiar flight characteristics compared with the aircraft. The first part of this paper is to derive the dynamic equation of motion for the mid-altitude unmanned airship and the second part is to obtain the optimal trajectories under the minimal time flight given constraints. The trajectory optimization problem is converted into the nonlinear programming problem using Sequential Quadratic Programming approach. Finally numerical solutions are presented in the last part of the paper.