• Advances in aircraft and spacecraft science
• /
• v.3 no.3
• /
• pp.243-257
• /
• 2016

The increase of air traffic volume has brought an increasing amount of issues related to carbon and NOx emissions and noise pollution. Aircraft manufacturers are concentrating their efforts to develop technologies to increase aircraft efficiency and consequently to reduce pollutant discharge and noise emission. Ultra High By-Pass Ratio engine concepts provide reduction of fuel consumption and noise emission thanks to a decrease of the jet velocity exhausting from the engine nozzles. In order to keep same thrust, mass flow and therefore section of fan/nacelle diameter should be increased to compensate velocity reduction. Such feature will lead to close-coupled architectures for engine installation under the wing. A strong jet-wing interaction resulting in a change of turbulent mixing in the aeroacoustic field as well as noise enhancement due to reflection phenomena are therefore expected. On the other hand, pressure fluctuations on the wing as well as on the fuselage represent the forcing loads, which stress panels causing vibrations. Some of these vibrations are re-emitted in the aeroacoustic field as vibration noise, some of them are transmitted in the cockpit as interior noise. In the present work, the interaction between a jet and wing or fuselage is reproduced by a flat surface tangential to an incompressible jet at different radial distances from the nozzle axis. The change in the aerodynamic field due to the presence of the rigid plate was studied by hot wire anemometric measurements, which provided a characterization of mean and fluctuating velocity fields in the jet plume. Pressure fluctuations acting on the flat plate were studied by cavity-mounted microphones which provided point-wise measurements in stream-wise and spanwise directions. Statistical description of velocity and wall pressure fields are determined in terms of Fourier-domain quantities. Scaling laws for pressure auto-spectra and coherence functions are also presented.

• Journal of Advanced Navigation Technology
• /
• v.26 no.3
• /
• pp.179-184
• /
• 2022

The accurate wing flexure model is required to improve the transfer alignment performance of guided weapon system mounted on a wing of fighter aircraft or armed helicopter. In order to solve this problem, mechanical or stochastical modeling methods have been studying, but modeling accuracy is too low to be applied to weapon systems. The deep learning techniques that have been studying recently are suitable for nonlinear. However, operating fighter aircraft for deep-learning modeling to secure a large amount of data is practically difficult. In this paper, it was used to generate amount of flexure data samples that are similar to the actual flexure data. And it was confirmed that generated data is similar to the actual data by utilizing "measures of similarity" which measures how much alike the two data objects are.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.2
• /
• pp.165-170
• /
• 2007

During the conceptual design phase of a wing-body-canard type fighter class aircraft, as a method of maneuverability enhancement for an aircraft, effects of canard-leading edge flap scheduling have been studied. In this study, corrected supersonic panel method has been used to predict the drag polar characteristics due to canard-leading edge flap deflections in the high speed regime. Utilizing the predicted drag polar curves, the canard-leading edge flap scheduling laws have been established. These scheduling laws are the relation of canard-leading edge flap deflections and the flight conditions to maximize the lift-drag ratio. Based on the results obtained from the canard-leading edge flap scheduling, the present method has shown to be useful to enhance the maneuverability of wing-body-canard type fighter class aircraft.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.21 no.1
• /
• pp.62-67
• /
• 2013

Human Powered Aircraft (HPA) should be light in weight and have high efficiency because power source of propulsion is human muscles. Airframe structure takes up most of empty weight of aircraft, so weight reduction of structure is very important issue for HPA. In this paper, design/analysis/test procedures for ultra light weight structure of the HPA developed by Korea Aerospace Research Institute (KARI) are explained briefly. Structural design is conducted through case studies on HPA in the USA and Japan. Loads analysis is performed to calculate design loads which is needed for structural design and analysis. Structural analysis is conducted for structure sizing. Static strength test of main wing spar which is primary structure of wing is performed to verify structural integrity.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.9
• /
• pp.665-677
• /
• 2019

The United States has implemented the TLCSM (Total Life Cycle System Management) to minimize the total lifecycle cost of aircraft and to improve operating availability. As a practical strategy, CBM + is required to be applied to new weapons systems. The F-35 aircraft applied PHM under CBM + concept from the development stage. In this study, we analyzed the technology trends, the level of PHM technology in Korea, and the development trends of foreign technology. Then, we analyzed the PHM technical elements and constructed the 5 phases of technical elements acquisition roadmap for military fixed wing aircraft parts PHM.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.6
• /
• pp.107-115
• /
• 2002

A parametric study has been conducted to evaluate the effects of finite element modeling methods on the internal loads, sizing and the weight of the multi-spar aircraft wing structures. The wing is idealized into total 18finite element models and subjected to 4typical external load conditions. An automatic sizing algorithm based on MSC/NASTRAN and MSC/PATRAN is developed. The results show that the critical part affection the internal loads and weight of the structure is wing skin. Effect of modeling of the spar and rib on the structural behavior is not manifest. On the contrast to the general expectation, the models using the bending-resistant elements show the heavier weight than ones by the elements without bending stiffness. From this results, designers of multi-spar wing are recommended to construct the finite element model considering the bending stiffness, or to check the characteristics of the structure before modeling.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.2
• /
• pp.98-106
• /
• 2019

Human-powered aircraft has wings with a shape of high aspect ratio which results in large bending displacement. This paper aims to improve the structural limitation by changing an incidence angle of the wings. The tendency change of bending displacement at the wing tip is observed assuming that airfoil and cross-sectional shape of the wing is fixed, and amount of the total lift generated is satisfied. Quasi-steady lift, drag and the aerodynamic moment are distributed with regard to sections of the wing. Those are analyzed using a numerical nonlinear lifting-line method and 'geometrically exact beam' (GEB) program in EDISON. 'Variational Asymptotic Beam Sectional Analysis' (VABS) program is used to check if the present wing is structurally solid. Furthermore, the predicted tip deflections are verified by comparing with DYMORE.

• Journal of Aerospace System Engineering
• /
• v.12 no.3
• /
• pp.38-44
• /
• 2018

Military aircraft may have fatigue cracks in structurally weak areas due to multiple factors such as the accumulation of flight time while perform various missions and unpredictable air conditions. As a fatigue crack progresses, there is a risk that the structure will be destroyed in extreme cases, which can have a significant impact on flight safety. In this study, a cracking phenomenon was observed during the periodic inspection the inner support of the fairing, which is installed to protect the connection between the wing and the body of the aircraft. Therefore, a study on a series of quality improvement processes for reformation was described. In order to identify the causes of cracks, pre-load generation occurrence during the wing assembly process was investigated and a fracture analysis was performed. Also, the design of the support structure was suggested in terms of preventing recurrence of cracks. The structural integrity was verified using a stress and fatigue life analysis.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.11
• /
• pp.1103-1111
• /
• 2014

The results of control law design for a tilt-rotor unmanned aerial vehicle that has a nacelle mounted wing extension (WE) are presented in this paper. It consists of a control surface mixer, stability and control augmentation system (SCAS), hold mode for altitude / speed / heading, and a guidance mode for preprogram and point navigation which includes automatic take-off and landing. The conversion corridor and the control moments derivatives between the original tilt-rotor and its variant of the nacelle mounted WE were compared to show the effectiveness of the WE. The nacelle conversion of the original tilt-rotor starts when the airspeed is greater than 30 km/h but its WE variant starts at 0 km/h in order to reduce the drag caused by the high incidence angle of the WE. The stability margins of the inner loop are presented with the optimization approach. The outer loops for the hold mode are designed with trial and error methods with linear and nonlinear simulation. The main control parameter for altitude control of the helicopter mode is thrust command and it is transferred to the pitch attitude command in airplane mode. Otherwise, the control parameter for the speed of the helicopter mode is the pitch attitude command and it is transferred to the thrust command in airplane mode. Therefore the speed and altitude hold mode are coupled to each other and are engaged at the same time when an internal pilot engages any of the altitude or speed hold modes. The nonlinear simulation results of the guidance control for the preprogrammed mode and point navigation are also presented including automatic take-off and landing in order to prove the full control law.

• Aerospace Engineering and Technology
• /
• v.1 no.1
• /
• pp.8-27
• /
• 2002

In this study, the load analysis of a composite canard aircraft is performed numerically. Excel visual basic program for PC is used to calculate aerodynamic coefficients, loads and moments etc.. The basic data required for the load analysis such as aircraft configuration and dimension, parts and its weight and coordinate etc. are obtained from Catia modeling, measurement or material density. Aircraft weight, center of gravity, inertia moment, structural design speeds, wing load distribution, forces and moments are evaluated by using these data. V-n diagram is also represented for selecting critical loads applied to the wing and fuselage. The V-n diagram is investigated to decide the flight envelope of canard aircraft for design speed VA, VC, VD and load factor +3.8G, -1.52G at maximum weight of 2,573 lbs and sea level. In the future, the results of the wing and fuselage load analysis is to represented by using selected critical loads.