• Proceedings of the Korea Crystallographic Association Conference
• /
• 2002.11a
• /
• pp.5-6
• /
• 2002

The new spectrometer for X-ray Induced Electron Emission Spectroscopy (XIEES) .has been recently developed in KRISS in collaboration with PTI (Russia). The spectrometer allows to perform research using the XAFS, SXAFS, XANES techniques (D.C.Koningsberger and R.Prins, 1988) as well as the number of techniques from XIEES field(L.A.Bakaleinikov et all, 1992). The experiments may be carried out with registration of transmitted through the sample x-rays (to investigate bulk samples) or/and total electron yield (TEY) from the sample surface that gives the high (down to several atomic mono-layers in soft x-ray region) near surface sensitivity. The combination of these methods together give the possibility to obtain a quantitative information on elemental composition, chemical state, atomic structure for powder samples and solids, including non-crystalline materials (the long range order is not required). The optical design of spectrometer is made according to Johannesson true focusing schematics and presented on the Fig.1. Five stepping motors are used to maintain the focusing condition during the photon energy scan (crystal angle, crystal position along rail, sample goniometer rail angle, sample goniometer position along rail and sample goniometer angle relatively of rail). All movements can be done independently and simultaneously that speeds up the setting of photon energy and allows the using of crystals with different Rowland radil. At present six curved crystals with different d-values and one flat synthetic multilayer are installed on revolver-type monochromator. This arrangement allows the wide range of x-rays from 100 eV up to 25 keV to be obtained. Another 4 stepping motors set exit slit width, sample angle, channeltron position and x-ray detector position. The differential pumping allows to unite vacuum chambers of spectrometer and x-ray generator avoiding the absorption of soft x-rays on Be foil of a window and in atmosphere. Another feature of vacuum system is separation of walls of vacuum chamber (which are deformed by the atmospheric pressure) from optical elements of spectrometer. This warrantees that the optical elements are precisely positioned. The detecting system of the spectrometer consists of two proportional counters, one scintillating detector and one channeltron detector. First proportional counter can be used as I/sub 0/-detector in transmission mode or by measuring the fluorescence from exit slit edge. The last installation can be used to measure the reference data (that is necessary in XANES measurements), in this case the reference sample is installed on slit knife edge. The second proportional counter measures the intensity of x-rays transmitted through the sample. The scintillating detector is used in the same way but on the air for the hard x-rays and for alignment purposes. Total electron yield from the sample is measured by channeltron. The spectrometer is fully controlled by special software that gives the high flexibility and reliability in carrying out of the experiments. Fig.2 and fig.3 present the typical XAFS spectra measured with spectrometer.

• Food Science and Preservation
• /
• v.18 no.3
• /
• pp.288-293
• /
• 2011

This study investigated the changes in the quality of fresh-cut lotus roots that were treated with hot water. Lotus roots were purchased from Daegu, Korea. They were washed, peeled, and cut into lcm-thick slices with a ceramic knife. The peeled and sliced lotus roots were dipped for 45 sec in water at 30, 55, and $80^{\circ}C$. After they were air-dried at room temperature, the slices were packed in polyethylene films and stored at $4^{\circ}C$ for 12 d. Then the changes in the weight loss, color, total viable cell, and sensory characteristics were measured. Generally, the weight loss of the lotus roots that were treated with hot water slightly increased. The application of the heat treatment delayed the browning of the lotus roots, especially the treatment with $55^{\circ}C$ hot water. The L and a values of the lotus roots that were treated with $80^{\circ}C$ hot water significantly increased during their storage, though. The heat treatment effectively inhibited the growth of microorganisms. The organoleptic quality of the lotus roots that were treated with $55^{\circ}C$ hot water was the best.

• Food Science and Preservation
• /
• v.19 no.6
• /
• pp.807-812
• /
• 2012

This study was investigated the changes in quality of heat treated fresh-cut lotus roots using various packaging materials. Lotus roots were purchased from Daegu, Korea. Lotus roots were washed, peeled and sliced with a sharp ceramic knife. The prepared peeled and sliced lotus roots were dipped for 45 sec in water at $55^{\circ}C$. After air-dried at room temperature, the slices were packaged with polyethylene films, polyethylene terephthalate tray+wrapping, vacuum packaging and then stored at $4^{\circ}C$. Changes in weight loss, color, firmness, microorganisms and sensory characteristics were measured. In general, the weight loss rate was increased slightly in vacuum packaged lotus roots. Application of heat treatment delayed browning of lotus roots, and especially vacuum packaged lotus roots were the most lowest ${\Delta}E$ value. However, L and ${\Delta}E$ value of PE film packaged lotus roots were increased highly during storage. The heat treated and vacuum packaging inhibited the growth of microorganisms effectively. The organoleptic quality of vacuum packaged lotus roots showed the best by sensory evaluation.

• Restorative Dentistry and Endodontics
• /
• v.27 no.2
• /
• pp.150-157
• /
• 2002

One of the latest concepts in bonding are "total etch", in which both enamel and dentin are etched with an acid to remove the smear layers, and "wet dentin" in which the dentin is not dry but left moist before application of the bonding primer Ideally the application of a bonding agent to tooth structure should be insensitive to minor contamination from oral fluids. Clinically, contaminations such as saliva, gingival fluid, blood and handpiece lubricant are often encountered by dentists during cavity preparation. The aim of this study was to evaluate the effect of contamination by hemostatic agents on shear bond strength of compomer restorations. One hundred and ten extracted human maxillary and mandibular molar teeth were collected. The teeth were removed soft tissue remnant and debris and stored in physiologic solution until they were used. Small flat area on dentin of the buccal surface were wet ground serially with 400, 800 and 1200 abrasive papers on automatic polishing machine. The teeth were randomly divided into 11 groups. Each group was conditioned as follows : Group 1: Dentin surface was not etched and not contaminated by hemostatic agents. Group 2: Dentin surface was not etched but was contaminated by Astringedent$^{\circledR}$(Ultradent product Inc., Utah, U.S.A.) Group 3: Dentin surface was not etched but was contaminated by Bosmin$^{\circledR}$(Jeil Pharm, Korea.). Group 4: Dentin surface was not etched but was contaminated by Epri-dent$^{\circledR}$(Epr Industries, NJ, U.S.A.). Group 5: Dentin surface was etched and not contaminated by hemostatic agents. Group 6: Dentin sorface was etched and contaminated by Astringedent$^{\circledR}$. Group 7 : Dentin surface was etched and contaminated by Bosmin$^{\circledR}$. Group 8: Dentin surface was etched and contaminated by Epri-dent$^{\circledR}$. Group 9: Dentin surface was contaminated by Astringedent$^{\circledR}$. The contaminated surface was rinsed by water and dried by compressed air. Group 10: Dentin surface was contaminated by Bosmin$^{\circledR}$. The contaminated surface was rinsed by water and dried by compressed air. Group 11 : Dentin surface was contaminated by Epri-dent$^{\circledR}$. The contaminated surface was rinsed by water and dried by compressed air. After surface conditioning, F2000$^{\circledR}$ was applicated on the conditoned dentin surface The teeth were thermocycled in distilled water at 5$^{\circ}C$ and 55$^{\circ}C$ for 1,000 cycles. The samples were placed on the binder with the bonded compomer-dentin interface parallel to the knife-edge shearing rod of the Universal Testing Machine(Zwick Z020, Zwick Co., Germany) running at a cross head speed or 1.0 mm/min. Group 2 showed significant decrease in shear bond strength compared with group 1 and group 6 showed significant decrease in shear bond strength compared with group 5. There were no significant differences in shear bond strength between group 5 and group 9, 10 and 11.