• Particle and aerosol research
• /
• v.12 no.4
• /
• pp.135-143
• /
• 2016

Removal of water contents in a gas is needed in industrial field of gas processing related on energy production/conversion, and environmental treatment. Inertial separators are economic devices for separating droplets from the gas stream. For accurate understanding of removal process in a curved vane mist eliminator, a numerical model including turbulent dispersion, evaporation and condensation of water vapor at surface of droplets is required. A two-stage curved vane mist eliminator has been modeled, and fluid flow of mixture of air and water vapor and droplet trajectories were solved simultaneously with taking into account two-way coupling. Removal efficiency of droplets with various inlet condition of relative humidities (RH, 40%, 90%, and 100%) were compared. As RH increased, the effect of evaporation decreased and inertial separation efficiencies of droplets obtained increased especially for droplets of diameter below 10 micrometers.

• Journal of Korean Society for Atmospheric Environment
• /
• v.31 no.5
• /
• pp.461-471
• /
• 2015

Base on emission factors derived from National Institute of Environmental Research, Particulate matter from combined cycle power plants (CCPPs) has been estimated to be a important source of $PM_{10}$. Generally there is no serious emission of particulate matter in CCPPs. because the fuel of them is natural gas. But emission gas after long shut down season has very high dust content. Therefore $PM_{10}$ emission rate is dependent on its operation mode. In this study, particulate dispersion study for new city near CCPPs complex has performed using CALPUFF model for three case. $PM_{10}$ concentration has big difference between normal operation and 2 case start-up condition after long shutdown. In normal operating conditions, daily $0.32{\sim}0.50{\mu}g/m^3$ influence on of the surrounding area. But when 1~2 aerobic high concentration discharged conditions, average concentration is higher about $9.2{\sim}34.1{\mu}g/m^3$ than normal operating conditions.

• Journal of environmental and Sanitary engineering
• /
• v.21 no.2 s.60
• /
• pp.11-19
• /
• 2006

Ran numerical analysis about simplicity warm current model (simple turbulence model) to examine closely distributed laying stress on NOx of contaminant that happen in downtown that building is massed and result is as following. Downtown building is massed and transfer of vehicles can know that frequent area receives greatly effect of building. Pollution displays class kind phenomenon striking in the building, class kind done pollution that show high density being mixed with pollution that happen in vehicles being flowed in again side know can. Divide velocity vector of pollution and density change to ancient city and did numerical analysis. Because NOx is flowed in diversion of water neighborhood by continuous this kind in Godo 20m point, density showed density of $0.0907mg/m^3s$, and can know that Banryuhyeon that Pollution strikes in the building at ancient city 30m point is decreased and approaches with freedom flowing without cooperation (cavity) phenomenon remarkably. Because pollution strikes in the building at distance shaft 383m point, class kind do phenomenon that know appeared notedly Nopeungeonmulgwanat between building pollution density $0.067mg/m^3$ head of a families high appear.

• Journal of Preventive Medicine and Public Health
• /
• v.16 no.1
• /
• pp.67-77
• /
• 1983

To investigate the an air pollution by particulate matter and its dispersion, a cement plant produceing portland cement 600,000 ton/year and its vicinity were surveyed from Obtober, 1980 to April, 1983. The survey was mainly focused on main stack emmission rate of the cement plant and particle size distribution in the dust, dustfall and total suspended particulate concentration in the area by month and distance from the stack. The results of the study were as follows; 1. The main stack emission rate was surveyed before and after the spray tower was additionally installed to the original E.P bag filter. Before the spray tower installed, the main stack emission rate was higher ($0.64g/Nm^3$) than the emission standard of Korean Environmental Preservation Law's ($0.59g/Nm^3$, amended to $0.4g/Nm^3$ on April 1983), but after the spray tower was installed, its main stack emission rate was markedly decreased to the standard ($0.43g/Nm^3$). 2. $2{\sim}3{\mu}m$ of the particle size was the largest portion (20.8%) of the dust particulate from the main stack and 50% of the frequency distribution was $1.5{\mu}m$ of the size. Most particle size was below $10{\mu}m$. 3. The spray tower reduced the dustfall to $37.81{\sim}9.76\;ton/km^2/month$ while dustfall appeared at $45.29-15.45ton/km^2/month$, in the vicinity of plant before spray tower installed 4. Mean concentrations of total suspended particulate for 24 hours of the various stations were determined in $20.6-200.0{\mu}g/m^3$, 3 stations of tham were higher than the value of Harry and William's arthmetic average standard $130{\mu}g/m^3$. 5. Linear regression between dustfall [X] and total suspended particulate[Y] concentration was an equation, Y=4.024X+11.479.[r=0.91] 6. During the whole seasons in the opposite area 100m apart from the omission source the prevailing wind direction was with estimated more than $30ton/km^2/month$, and the concentration of total suspended particulate for 24 hours averaging time was more than $140{\mu}g/m^3$ in the same area and direction. 7. Assuming the wind direction were constant through the day dustfalls for a day were estimated at $13.40ton/km^2/day,\;10.79ton/km^2/day$ and $4.55ton/km^2/day$ at various distances of 100m, 500m and 1,500m from the emission source respectively. 8. In the simutalion of dustfall and suspended dust by area, Gaussian dispersion model modified by size distribution of particulate matter was not applicated since the emission of dust were from multi sources other them stack. From the above results, it could be applied that the dispersion of dust from the cement plant is estimated and regulated for the purpose of environmental protection.

• Applied Microscopy
• /
• v.47 no.3
• /
• pp.131-147
• /
• 2017

In this work further optical and electrical investigations of pure and Zr doped $Mn_3O_4$ (from 0 up to 20 at.%) thin films as a function of frequency. First, the refractive index, the extinction coefficient and the dielectric constants in terms of Zr content are reached from transmittance and reflectance data. The dispersion of the refractive index is discussed by means of Cauchy model and Wemple and DiDomenico single oscillator models. By exploiting these results, it was possible to estimate the plasma pulse ${\omega}_p$, the relaxation time ${\tau}$ and the dielectric constant ${\varepsilon}_{\infty}$. Second, we have performed original ac and dc conductivity studies inspired from Jonscher model and Arrhenius law. These studies helped establishing significant correlation between temperature, activation energy and Zr content. From the spectroscopy impedance analysis, we investigated the frequency relaxation phenomenon and hopping mechanisms of such thin films. Moreover, a special emphasis has been putted on the effect of the oxidation in air of hausmannite thin films to form $Mn_2O_3$ ones at $350^{\circ}C$. This intrigue phenomenon which occurred at such temperature is discussed along with this electrical study. Finally, all results have been discussed in terms of the thermal activation energies which were determined with two methods for both undoped and Zr doped $Mn_3O_4$ thin films in two temperature ranges.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.43 no.5
• /
• pp.55-64
• /
• 2015

In this study, negative air ions, which can increase comfort and positively influence human health, was set as an evaluative factor for school forests. The characteristics, location and microclimate of school forests were examined to determine an effective school forest model for maximum negative air ion generation. It also aimed to provide basic data for the development of urban green fields. The negative air ion concentrations were different according to the green types. The order from the highest to the lowest was: single-layer structure($934ea/cm^3$) > multi-layer structure($794ea/cm^3$) > grass($553ea/cm^3$) > bare ground($529ea/cm^3$). As for the correlation with microclimate, negative air ion concentration was negatively correlated with temperature. The negative air ion concentration was significantly different according to planting type. The negative air ion concentration was higher at single-layer structure sites than at multi-layer structure sites, which appears to indicate that the temperature is higher when the vegetation structure was single-layer compared to multi-layer. Wind speed was higher at the single-layer planted site than at the multi-layer planted site. The vegetation wind shielding effect was lower at single-layer planted sites than at multi-layer planted sites. The single-layer planted site provided more favorable conditions for the generation and dispersion of negative air ions.

• Journal of Korean Society for Atmospheric Environment
• /
• v.25 no.6
• /
• pp.550-561
• /
• 2009

This study is to investigate the air pollution characteristics of an industrialized midsize west-coastal city by comparing air quality to a neighboring inland city. The hourly averaged data of $O_3$, $SO_2$, $NO_2$, CO, and $PM_{10}$ measured from continuous air quality monitoring sites in Gunsan (coastal) and Jeonju (inland) were analyzed. The data set covers the period from 2004 to 2006. The annual average concentrations of the air pollutants in two cities were compared in their abundances and temporal trends as well. $O_3$ and $SO_2$ in Gunsan were relatively higher than those in Jeonju, while vice versa in case of $NO_2$ and $PM_{10}$. It seems that heavy automobile emissions from Jeonju mainly bring on higher $NO_2$ and $PM_{10}$ than those in Gunsan on annual base. $NO_2$ concentrations in both cities showed bimodal diurnal variations with peaks in the morning and in the late evening. These peaks correspond to the coupled effects of rush hour traffic and meteorological conditions (i.e., variation of mixing height and dispersion conditions). Maximum hourly averages of $NO_2$ ranged from 18 ppb to 28 ppb at Jeonju, and from 12 ppb to 20 ppb at Gunsan. $O_3$ showed typical diurnal variation with a maximum in the afternoon between 14:00 and 16:00 LST. Diurnal variations of CO and $PM_{10}$ were similar to $NO_2$ while $SO_2$ was similar to $O_3$. Seasonal variations of $PM_{10}$ in both cities indicated that their concentrations during spring season were significantly high. Asian dust storms occur frequently during spring and seem to affect increase in $PM_{10}$. High $O_3$ and $PM_{10}$ days were selected from both cities. The analyses based on the HYSPLIT trajectory model during the high $O_3$ and $PM_{10}$ showed these episodes (six cases) were mostly coincident with Asian dust storm originated from northern China and Mongolia. However, these high air pollution episodes in the west coastal cities may not only be caused by the Asian dust but also affected by other air pollutants transported from China accompanying the Asian dust.

• Journal of Korean Society for Atmospheric Environment
• /
• v.25 no.1
• /
• pp.15-25
• /
• 2009

Donghae city is one of the most representative cement industrial city in Korea. The area is faced with the East Sea to the East and with high montane region of Tae-Back mountain range to the West. Many pollutant sources of air pollution are located near the coast, but the largest point sources of the region are located at the bottom of the mountain area in Donghae city. The local wind is highly affected by local topography and plays an important role in transport and dispersion of contaminants from the pollution sources. This study was designed to evaluate enhancement of MM5 predictions by using Four Dimensional Data Assimilation (FDDA), the SONDE data and the national meteorological station, data only. The alternative meteorological fields predicted with and without FDDA were used to simulate spatial and temporal variations of NOx in combined with Atmospheric Dispersion Models (CALPUFF). For the modeling domain, the alternative meteorological fields with 1.1 km spatial resolution were interpolated to the CALMET with 0.5 km resolution. The vertical layers set to have 35 and 12 layers for MM5 and CALPUFF, respectively. MM5 with the FDDA did not resulted in significant improvement of meteorological field prediction in Donghae region, which is primarily because of complex geography and wind scheme. The result of CALPUFF, however, showed reduction of uncertainty errors by using the interpolation scheme of the actual measurement data.

• Journal of Environmental Impact Assessment
• /
• v.31 no.5
• /
• pp.271-285
• /
• 2022

The AERMET, the AERMOD meteorological preprocessing program, mainly used for environmental impact assessment and Integrated Environmental Permit System (IEPS) in Korea, has not considered the land covers characterasitics, and used only the past meteorological data format CD-144. In this study, two results of AERMET application considering CD-144 format and ISHD format, being used internationally, were compared. Also, the atmospheric dispersion characteristics were analyzed with consideration of land cover. In the case of considered the CD-144 format, the actual wind speed was not taken into account in the weak wind (0.6~0.9m/s) and other wind speed due to the unit conversion problem. The predicted concentration considering land cover data was up to 387% larger depending on the topographic and emission conditions than without consideration of land cover. In conclusion, when using meteorological preprocessing program in AERMOD modelling, AERMET, with ISHD format, land cover characterasitics in the area should be considered.

• The Journal of the Acoustical Society of Korea
• /
• v.29 no.7
• /
• pp.448-457
• /
• 2010

Vibrations and wave propagations in waveguide structures can be analysed efficiently by using waveguide finite element (WFE) method. The WFE method only models the 2-dimensional cross-section of the waveguide with finite elements so that the size of the model and computing time are much less than those of the 3-dimensional FE models. For cylindrical shells or pipes which have simple cross-sections, the external coupling with fluids can be treated theoretically. For waveguides of complex cross-sectional geometries, however, numerical methods are required to deal with external fluids. In this numerical approach, the external fluid is modelled by the boundary elements (BEs) and connected to WFEs. In order to validate this WFE/BE method, a pipe submerged in water is considered in this study. The dispersion diagrams and point mobilities of the pipe simulated are compared to those that theoretically obtained. Also the acoustic powers radiated from the pipe are predicted and compared in both cases of air and water as an external medium.