• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.20 no.10
• /
• pp.689-695
• /
• 2008

Experimental study has been performed to investigate the influence of non-condensible gas(NCG) charged mass on the thermal performance of a variable conductance heat pipe(VCHP) with screen mesh wick. The VCHP is furnished by screen mesh number 200 for the pipe outer diameter of 12.7mm and the pipe length of 500 mm. The VCHP is filled with water as working fluid of 4.8g and nitrogen as NCG and has evaporator, condenser and adiabatic section, respectively. For the results from experiment, it is found that, for the same charged mass of working fluid, the overall wall temperatures of heat pipe grows up with increasing NCG charged mass. The variation of operating temperature of VCHP reduces with increasing NCG mass. In addition, the profile of axial wall temperature distribution is presented for heat transport capacity of heat pipe, the temperature of cooling water of condenser, inclination angle, and operating temperature.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.21 no.2
• /
• pp.109-117
• /
• 2009

In this study, thermodynamic performance of R430A is examined both numerically and experimentally in an effort to replace HFC134a used in the refrigeration system of domestic water purifiers. Even though HFC134a is used predominantly in such a system these days, it needs to be phased out in the near future in Europe and most of the developed countries due to its high global warming potential. To solve this problem, cycle simulation and experimental measurements are carried out with a new refrigerant mixture of 76%R152a124% R600a using actual domestic water purifiers. This mixture is numbered and listed as R430A by ASHRAE recently. Test results show that the system performance with R430A is greatly influenced by the amount of charge due to the small internal volume of the refrigeration system of the domestic water purifiers. With the optimum amount of charge of 21 to 22 grams, about 50% of HFC134a, the energy consumption of R430A is 13.4% lower than that of HFC 134a. The compressor dome and discharge temperatures and condenser center temperature of R430A are very similar to those of HFC134a at the optimum charge. Overall, R430A, a new long term environmentally safe refrigerant, is a good alternative for HFC134a requiring little change in the refrigeration system of the domestic water purifiers.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.17 no.2
• /
• pp.173-182
• /
• 2005

The Performance of U-tube ground heat exchanger for geothermal heat Pump systems depends on the thermal properties of the soil, as well as grout or backfill materials in the borehole. In-situ tests provide a means of estimating some of these properties. In this study, in-situ thermal response tests were completed on two vertical boreholes, 130 m deep with 62 mm diameter high density polyethylene U-tubes. The tests were conducted by adding a monitored amount of heat to water over a $17\~18$ hour period for each vertical boreholes. By monitoring the water temperatures entering and exiting the loop and heat load, overall thermal conductivity values of grout/soil formation were determined. Two parameter estimation models for evaluation of thermal response test data were compared when applied on the same temperature response data. One model is based on line-source theory and the other is a numerical one-dimensional finite difference model. The average thermal conductivity deviation between measured data and these models is of the magnitude $1\%$ to $5\%$.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.19 no.8
• /
• pp.585-592
• /
• 2007

Good cold start characteristics are essential for satisfactory operation of fuel cell vehicles. In this study, the melting process has been numerically investigated for a water tank used in fuel cell vehicles. The 2-D model of the tank containing ice and plate heaters was assumed and the unsteady melting process of the ice was calculated. The enthalpy method was used for the description of the melting process, and a FVM code was used to solve the problem. The feasibility study compared with other experiment showed that the developed program was able to describe the melting process well. From the numerical analysis carried out for different wall temperatures of the pate heaters, some important design factors could be found such as local overheating and pressurization in the tank.

• Journal of the Korea Furniture Society
• /
• v.18 no.2
• /
• pp.143-146
• /
• 2007

This study was carried out to assess the dimensional stability of wood material treated by plastic processing for bentwood and compression wood. The evaluation method was different between two wood materials, but the treatments for them were very similar to each other. One of the main methods is heat treatment with sufficient water vapor. In bentwood, the used species were painted maple (Acer mono), bitter wood (Picrasma quassioides) and birch (Betula schmidtii). Steaming was the worst treatment method for dimensional stabilization of bentwood. The best results could be attained with PEG treatment for dimensional stabilization of bentwood. Dimensional stability of bitter wood was found to be conspicuous. However the steaming treatment at lower temperatures, i.e., about $130^{\circ}C$ was not suitable for dimensional stability of bentwood. In compression wood, the used specimen was Italian poplar wood (Populus euramericana). Two heat compressive pressing conditions, an open-press system and an air-tighten closed-press system, were used. The recovery rate was measured after boiling and/or absorbing in water to estimate the dimensional stability of heat compressed wood. The best dimensional stability of compressed wood in the air-tighten closed-press system was found to be better at $200^{\circ}C$ than $180^{\circ}C$. The best compression rate for dimensional stability was 73 percent.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.12 no.6
• /
• pp.533-540
• /
• 2000

Condensation heat transfer characteristics have been investigated experimentally when a water vapor is condensed on the outside of a horizontal copper tube in a condenser. This problem is of particular interest in the design of a LiBr-water absorption system. Hydrophilic surface modification was performed to increase the wettability on the copper tube. The optimum hydrophilic treatment condition using acethylene and nitrogen as reaction gas is also studied in detail. The results obtained indicate that the optimum reaction gas ratio of acethylene to nitrogen for hydrophilic surface modification was found to be 7 : 3 for the best condensation heat transfer. In the wide ranges of coolant inlet temperatures, and coolant mass flow rates, both the condensation heat transfer rate and the condensation heat transfer coefficient of a hydrophilic copper tube are increased substantially, compared with those of a conventional copper tube used in a condenser. It is also found that the condensation heat transfer enhancement by the hydrophilic surface modification still emains even after a hundred cycles of wet/dry processes.

• Textile Coloration and Finishing
• /
• v.35 no.4
• /
• pp.256-273
• /
• 2023

Among the dyeing industries, the tenter process is a process that improves the quality of fibers by drying and ironing (heat treatment) dyed fabrics, and drugs such as water repellents, antistatic agents, and fiber softeners are mainly used in these tenter processes. These drugs are vaporized in the process of treatment by high temperatures (180 ~ 230℃), and are observed in a complex form such as white smoke, oil mist, and fine dust, causing odor. To treat the complex exhaust gas at the rear end of the tenter facility, most companies operate by installing a wet scrubber and an adsorption tower alone or in parallel, but there are many problems. In particular, the insoluble oil mist at the rear end of the tenter has significantly low processing efficiency in the cleaning dust collection facility, and there is a problem in the facility by adsorption due to the occlusion phenomenon caused by the oil mist. In addition, the odor gas at the rear end of the tenter contains a lot of aldehydes, and in order to improve these various problems, a complex exhaust purification device using cyclone and electric support collector was developed. This study examined the applicability of economical and efficient technology by removing complex air pollution at the rear end of the tenter and applying improved technology than the existing technology.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.4 no.4
• /
• pp.263-276
• /
• 1992

The transmission current in a power cable is determined under the condition of separate pipe cooling. To this end, the thermal analysis is conducted with the standard condition of separate pipe cooling system, which constitutes one of the underground power transmission system. The changes of transmission current in a power cable with respect to the variation of temperatures and flow rates of inlet cooling water as well as the cooling spans are also determined. As a consequnce, the corresponding transmission current is shown to vary within allowable limit, resulting in the linear variation of the current for most of the cable routes. The abrupt changes of current, however, for the given flow rate of inlet cooling water in some cooling span lead to the adverse effects on the smooth current transmission within the underground power transmission system. In practice, it is expected that the desinging of the separate pipe cooling system in conjunction with the evaluation of system capacity should take into account the effects of design condition on the inlet cooling flow rate.

• Computers and Concrete
• /
• v.6 no.6
• /
• pp.437-450
• /
• 2009

The effect of six different curing conditions on compressive strength and ultrasonic pulse velocity (UPV) of volcanic pumice concrete (VPC) and normal concrete (NC) has been studied. The curing conditions include water, air, low temperature ($4^{\circ}C$) and different elevated temperatures of up to $110^{\circ}C$. The curing age varies from 3 days to 91 days. The development in the pulse velocity and the compressive strength is found to be higher in full water curing than the other curing conditions. The reduction of pulse velocity and compressive strength is more in high temperature curing conditions and also more in VPC compared to NC. Curing conditions affect the relationship between pulse velocity and compressive strength of both VPC and NC.

• Journal of Powder Materials
• /
• v.9 no.4
• /
• pp.218-226
• /
• 2002

The purpose of the present study is to investigate the influence of thermal debinding and sintering conditions on the sintering behavior and mechanical properties of PIMed 316L stainless steel. The water atomized powders were mixed with multi-component wax-base binder system, injection molded into flat tensile specimens. Binder was removed by solvent immersion method followed by thermal debinding, which was carried out in air and hydrogen atmospheres. Sintering was done in hydrogen for 1 hour at temperatures ranging from 1000℃ to 1350℃ The weight loss, residual carbon and oxygen contents were monitored at each stage of debinding and sintering processes. Tensile properties of the sintered specimen varied depending on the densification and the characteristics of the grain boundaries, which includes the pore morphology and residual oxides at the boundaries. The sinter density, tensile strength (UTS), and elongation to fracture of the optimized specimen were 95%, 540 MPa, and 53%, respectively.