• 한국농림기상학회지
• /
• 제22권3호
• /
• pp.144-151
• /
• 2020

작물을 재배하는 동시에 전력 생산도 가능한 영농형 태양광 발전은 농업·농촌 분야와 재생에너지 산업 모두로부터 주목 받고 있다. 하지만, 그 역사가 짧은 만큼 영농형 태양광 하부에서의 미기상 환경 변화에 대한 이해와 관측 방법론이 정립되지 않은 실정이다. 따라서 본고에서는 보성군에 설치된 영농형 태양광에서 2019년 11월 부터 2020년 5월까지의 보리 생육기간 동안 일사광, 광합성유효복사광, 기온, 습도, 토양습도·온도, 풍향·풍속을 5분 간격으로 측정하여 공개했다. 또한, 노지의 일사량 및 광합성유효복사량에 대한 약 13일 간의 자료 결손에 대해서는 가까운 기상청 관측 자료를 활용하거나 영농형 태양광 하부의 자료를 이용한 두 가지 경험적 메우기 방법을 제안하였다. 본고 자료가 영농형 태양광에 대한 농업적 평가에 다양하게 활용되기를 기대한다.

• 수산해양기술연구
• /
• 제46권4호
• /
• pp.466-475
• /
• 2010

This study intends to present a direction for the better reforming of fishers'onboard living conditions and proposals for preparing for ratification of the Work in Fishing Convention by means of making a comparison between standards on recent national fishing vessel accommodation facilities and standards on the Work in Fishing Convention and Its Recommendation, 2007, ILO. For the most part of standards on national fishing vessel accommodation facilities are somewhat insufficient to satisfy the provisions in Annex III of the Convention. Considering by items on fishing vessel accommodation facilities, the standards on insect protector, noise and vibration, heating and air conditioning, lighting, persons per sleeping room, recreational facility are not provided in national law. Headroom, separation of accommodation, sleeping room floor area, mattress size, mess room, galley and food storage are partially sufficient for the Convention. In case of sanitary facilities, national standards are not sufficient for the Convention. The other side, facilities related safety of ship and crew such as emergency escape etc., are fully sufficient for the Convention. These insufficiencies caused by different types of fishing vessel depend on originality of fishing method and practices. In the comparison between equivalent tonnage about vessel's length on convention and calculated tonnage of national existing fishing vessel, the difference are 226tons about length 24m and 501tons about length 45m. For that reason, headroom, persons per sleeping room, cabin of sicker and injured, sanitary facilities may decide to use gross tonnage in place of length (L) and the alleviating measure basis of convention. But in case of standards on sanitary facilities which are unsufficient for the Convention, specially in coastal fishing vessel length basis should be adopted with alleviating basis for less than length 24m.

• 한국통신학회논문지
• /
• 제29권3A호
• /
• pp.303-310
• /
• 2004

본 논문에서는 5.15-5.35㎓ 대역의 무선 LAN용 L-슬롯 마이크로스트립 안테나를 설계 제작하였다. 정사각 패치에 사이즈 감소를 위해 4개의 L-슬롯을 갖도록 하였으며 접지면과 기판사이에 공기층을 삽입하여 VSWR＜1.5에서 적절한 대역을 얻고자 하였다. 설계시 주요 파라미터는 L-슬롯의 길이, 폭, 위치와 공기층의 두께 및 급전위치였으며 최적화된 파라미터를 가지고 실제 제작 및 측정하였다. 제작된 안테나의 측정결과는 다음과 같다. 공진 주파수는 5.25㎓이고, VSWR＜1.5에서 5%의 대역폭과 8-9㏈i의 이득을 얼었다. H-평면과 E-평면에서 각각 69$^{\circ}$와 62$^{\circ}$로 나타났다.

• KIEAE Journal
• /
• 제11권3호
• /
• pp.57-62
• /
• 2011

Asbestos have been used around the world because of reliable and cost-effective physicochemical characteristics. After incubation period about 15-40 years asbestos can cause various cancers, including malignant mesothelioma when inhaled into the air. These properties turned out, asbestos have been banned from using in developed countries. Also in Korea also, the use of asbestos was banned across the board by revision of Industry Safety and Health Act in February 2009. Therefore, the problem of asbestos is not when using. It is about dismantling, maintenance, and the final processing of asbestos waste. Asbestos Cement slates which is Widely distributed throughout the country as roofing materials has much scattering potential compare with inside materials. Also Ministry of Environment is planning to introduce legislation 'Asbestos Safety Management Act' through Environment Announcement and The same Act. 24 show as follows. Minister of Environment or governor should do survey on the actual condition targeting rural buildings with slates and partly or fully fund to dissolve, remove asbestos slate which was used in each buildings. Therefore, to solve these problems, database-building and necessity of management strategies have been continually arisen. So this study was performed. Its application value is very high in terms of its political, economic. Asbestos Cement Slates database could build to collect national registered building data and then using GIS, asbestos cement Slates distribution map were constructed in each province's cities and counties of the country. And this map by Application, construction was to visualize by application, construction of year. Through these results, information of Asbestos Cement Slates could visually inform to policy makers, asbestos dismantling and management contractor, and civilian and it would alleviate the gap of knowledge information. This is expected to be utilized by medium and long-term and effective plan for demolition and dismantling of asbestos cement Slates.

• 한국전자파학회논문지
• /
• 제11권4호
• /
• pp.505-513
• /
• 2000

본 논문에서는 편파 다이버서티(j:X)larization diversity)용 광대역 안테나에 대한 성능을 개선하기 위한 새로운 구조를 제안하였다. 이중 편파 마이크로스트립 안테나를 구현하기 위하여 십자형 개구변을 두었고, 개구면 위와 아래에 두 j:X)rt가 서로 수직이 되도록 급전부를 셜계하였다. 그리고 방사소자와 급전부에 air gap을 주었으며 후 방 방사를 줄이기 위해 아래 급전부로부터 $\lambda$/4 떨어뜨려서 반사판을 두었다. 더욱 넓은 대역폭을 가지도록 방 사 패치에 톱니 모양의 perturbation을 주었으며, 패치의 perturbation 효과에 의해 안테나 크기가 줄어들게 됨으 로써 배열 안테나의 크기도 상당히 줄어들었다. 제안된 단일 소자 안테나를 이용하여 $1\times4$ 배열 안테나 구조를 가진 PCS 기지국용 편파 다이버시티 안테나 를 제작하였다. 단일 소자 안테나는 각각 port 당 10.3 %, 11.3 %(VSWR<1.3)의 대역폭을 가지고 두 port간의 분리도가 -40 dB 이상이다. 또한 배열 안테나의 대역폭은 각각 13.2 %, 12.7 %(VSWR <1.3)이고 -36 dB의 분 리도와 10 dB의 XPD를 가진다.

• 한국전기전자재료학회논문지
• /
• 제29권8호
• /
• pp.470-475
• /
• 2016

In this study, $Zn_xMn_{3-x}O_4$ (x=0.95~1.20) specimens were prepared by using a conventional mixed oxide method. All specimens were sintered in air at $1,200^{\circ}C$ for 12 h and cooled at a rate of $2^{\circ}C/min$ to $800^{\circ}C$, subsequently quenching to room temperature. We investigated the structural and electrical properties of $Zn_xMn_{3-x}O_4$ specimens with variation of ZnO amount for the application of NTC thermistors. As results of X-ray diffraction patterns, all specimens showed the formation of a complete solid solution with tetragonal spinel phase. And, the second phase was observed by the solubility limit of Zn ions in $x{\geq}1.10$ composition. The average grain size was increased from $2.72{\mu}m$ to $4.18{\mu}m$ with increasing the compositional ratio of Zn ion from x=0.95 to 1.20, respectively. $Zn_{1.10}Mn_{1.90}O_4$ specimen showed the minimum electrical resistance of $57.5k{\Omega}$ at room temperature and activation energy of 0.392 eV.

• 한국유체기계학회 논문집
• /
• 제10권5호
• /
• pp.54-63
• /
• 2007

A barrel is a high length-to-diameter ratio cylinder that is influenced by environmental factors such as sunlight, precipitation, wind and clouds. Cross-barrel temperature differences caused by uneven heating or cooling lead to thermal deformation that degrades accuracy. Therefore, a barrel is covered by thermal shrouds to minimize the type of thermal deformation, "fall-of-shot". In this paper, an analytical and experimental study is presented to design the thermal shrouds for a gun barrel and to evaluate the thermal shroud effect. First, an analytical study on the thermal shroud effect to minimize thermal deformation of a gun barrel by sunlight and wind is performed. The coupled analysis of thermal fluid dynamics of the air flow between a barrel and thermal shrouds and thermal stresses of a barrel Is performed to clarify both the thermal shroud effect and the drift in gun muzzle orientation by thermal deformation. Second, experiments are carried out to test and evaluate the thermal shroud effect on the performance of a gun barrel. The drift in gun muzzle orientation against the solar radiation is confirmed by the experiments, and the results well agree with the analytical estimation. Third, three principal design factors that are presumed to have an effect on the performance of the thermal shrouds are also analyzed; sorts of shroud materials, wall-thickness of thermal shrouds, and distance of the gap between a barrel and thermal shrouds.

• Bulletin of the Korean Chemical Society
• /
• 제35권10호
• /
• pp.3052-3058
• /
• 2014

In this article, we have designed and synthesized a novel donor-${\pi}$-acceptor (D-${\pi}$-A) type porphyrin-based sensitizer (denoted UI-5), in which a carboxyl anchoring group and a 9,9-dimethyl fluorene were introduced at the meso-positions of porphyrin ring via phenylethynyl and ethynyl bridging units, respectively. Long alkoxy chains in ortho-positions of the phenyls were supposed to reduce the degree of dye aggregation, which tends to affect electron injection yield in a photovoltaic cell. The cyclic voltammetry was employed to determine the band gap of UI-5 to be 1.41 eV based on the HOMO and LUMO energy levels, which were estimated by the onset oxidation and reduction potentials. The incident monochromatic photon-to-current conversion efficiency of the UI-5 DSSC assembled with double-layer (20 nm-sized $TiO_2$/400 nm-sized $TiO_2$) film electrodes appeared lower upon overall ranges of the excitation wavelengths, but exhibited a higher value over the NIR ranges (${\lambda}$ = 650-700 nm) compared to the common reference sensitizer N719. The UI-5-sensitized cell yielded a relatively poor device performance with an overall conversion efficiency of 0.74% with a short circuit photocurrent density of $3.05mA/cm^2$, an open circuit voltage of 0.54 mV and a fill factor of 0.44 under the standard global air mass (AM 1.5) solar conditions. However, our report about the synthesis and the photovoltaic characteristics of a porphyrin-based sensitizer in a D-${\pi}$-A structure demonstrated a significant complex relationship between the sensitizer structure and the cell performance.

• 대한기계학회논문집A
• /
• 제25권8호
• /
• pp.1294-1301
• /
• 2001

In order to reduce the time and cost for assembly, automobile speaker grills have been injection molded with door trims or map pockets in one piece recently. However, several defects such as short shots or air traps can easily occur due to the decreased fluidity of the melting polymer according to the excessive heat transfer to the mold. Therefore, it is necessary to optimize the resin feed system and predict possible defects by CAE analysis. However it is not possible to obtain exact analysis results for the speaker grill by using general shell elements since the heat transfer in the thickness direction which is the dominant factor of the filling stage can not be considered. Therefore, there have been several efforts to simulate the injection molding nature of the speaker grill by using shell elements with an effective thickness which is smaller than the actual thickness of the part. Two empirical values have been recommended for the effective thickness in real practice. One is 50∼70% of the thickness of the speaker grill and another is the gap distance between the adjacent holes. In this paper, CAE analyses of a map pocket with a speaker grill were conducted using shell elements with both of these recommended effective thicknesses, and the predicted flow fronts were compared with the findings from injection molding experiments. The commercial code MOLDFLOW was used for injection molding analysis and an 850 ton injection molding machine was used for experiments.

• 문화기술의 융합
• /
• 제6권2호
• /
• pp.529-534
• /
• 2020

인류 문명의 발전은 산업화에 따른 도시의 발전과 운송 기술의 진화와 맥을 같이한다. 지금까지의 도시 발전은 수송비 절감과 한정된 중심업무 지구로서의 토지 이용 요구에 따라 진행되어왔다. 도시 인구 밀집도의 지속적인 증가는 지가상승, 교통 혼잡, 빈부격차, 공해발생 등과 같이 사회·경제적으로 많은 문제를 일으켜 왔고 현재의 도시 생태 시스템으로는 전반적인 해결에 어려움이 있다. 그러나 문제의 해결을 위한 실마리는 바로 도시생태계 내에서 찾을 수 있다. 서울 심야버스 운행 노선의 설계는 바로 심야의 도시 내 이동 인구의 흐름을 정보통신 기술을 이용해 분석하여 얻은 결과이다. 이렇듯 도시 문제의 해결은 도시 생태계의 분석에서 출발하는 것이 타당하다. 문제의 원인을 알았다면 시민의 삶의 질을 높이기 위해 빅데이터 플랫폼 구축이 필요하고 이를 통한 해결이 가능하다. 이 플랫폼의 중심에는 정보통신 기술의 기반 하에 도시의 구성 요소와 연결되어 실시간 수집, 분석 및 적용되는 빅데이터가 자리 잡고 있어야한다. 본 연구를 통해 지속 가능한 스마트 시티를 위한 빅데이터 플랫폼 구축과 적용 방안에 대하여 고찰한다.