• 한국미생물·생명공학회지
• /
• 제17권5호
• /
• pp.468-474
• /
• 1989

Pseudomonas delafieldii이 다당류 생산을 위한 배양조건을 검토하였다. 최적 배지조성은 glucose 25g/$\ell$, peptone 2.06 g/$\ell$, yeast extract 0.5g/$\ell$, KH$_2$PO$_4$2g/$\ell$, MgSO$_4$2g/$\ell$, CaCO$_3$2.5g/$\ell$이며 교반속도는 300rpm, 온도는 30도, pH는 6.5이었다. 이 조건에서는 flask culture를 할 경우 5.91g/$\ell$가 생산되며 이 때 수율은 23.65%, overall productivity는 50.98mg/g/h이었다.

• 한국미생물·생명공학회지
• /
• 제28권6호
• /
• pp.349-354
• /
• 2000

Culture conditions and nitrogen sources were optimized for production of erythritol, a natural sweetener, by Candida magnoliae M26. The optimal culture conditions were found to be culture temperature of $28^{\circ}C$, initial pH of 7, aeration of 1 vvm and agitation speed of 500 rpm in a 2.5 1 jar-fermentor. Glucose was chosen as the best carbon cource bsed on cell growth and erythritol productivity. Kight steep water(LSW) and corn steep liquor (CSL) which are by-products in starch processing from corn were tested as a nitrogen source substitute for yeast extract. The use of either LSW or CSL did not change the fermentation performance. The experimental results using LSW and CSL showed 1.5 times higher in cell growth and almost the same value in erythritol productivity com-pared with the control fermentation using yeast extract as a nitrogen source. These results suggested that either LSW of CSL could be used as a nitrogen source in a large-scale fermentation for erythritol production.

• Journal of Microbiology and Biotechnology
• /
• 제19권12호
• /
• pp.1603-1611
• /
• 2009

High-cell-density cultivation of yeast was investigated using the agricultural waste products corn steep liquor (CSL) and molasses. The Saccharomyces cerevisiae KV-25 cell mass was significantly dependent on the ratio between C and N sources. The concentrations of molasses and CSL in the culture medium were statistically optimized at 10.25% (v/v) and 16.87% (v/v), respectively, by response surface methodology (RSM). Batch culture in a 5-l stirred tank reactor using the optimized medium resulted in a cell mass production of 36.5 g/l. In the fed-batch culture, the feed phase was preceded by a batch phase using the optimized medium, and a very high dried-cell-mass yield of 187.63 g/l was successfully attained by feeding a mixture of 20% (v/v) molasses and 80% (v/v) CSL at a rate of 22 ml/h. In this system, the production of cell mass depended mainly on the agitation speed, the composition of the feed medium, and the glucose level in the medium, but only slightly on the aeration rate.

• 한국미생물·생명공학회지
• /
• 제24권6호
• /
• pp.756-762
• /
• 1996

In order to develop the method for mass production of natural food colorant from Monascus anka, optimum cultivation conditions for producing red and yellow pigments by cultiva- ting the mold in a jar fermenter and their color characteristics were investigated. The mold produced red and yellow pigments both intracellularly and extracellularly. These pigments showed unique light absorption characteristics with maximum absorption of 494, 380, 506, and 388 nm for extracellular red pigment (ERP), extracellular yellow pigment (EYP), intracellular red pigment (IRP), and intracellular yellow pigment (IYP), respectively. Optimum conditions for producing red pigments were found to be temperature 30$\circ$C, initial pH 6.0, rice powder 3-5%, peptone 0.05%, magnesium sulfate 0.25%, aeration rate 0.1 vvm. Optimum temperature for producing yellow pigments was around 35$\circ$C which is higher than that of producing red pigments. The initial pH and rice powder concentration for producing yellow pigments were the same as those of producing red pigments. The higher concentration of nitrogen source and inorganic salt, aeration rate, the more the yellow pigments were produced. The optimum agitation speed was 100 - 300 rpm for pigment production.

• 한국응용과학기술학회지
• /
• 제23권2호
• /
• pp.169-176
• /
• 2006

Acrylic adhesives for automobiles protection were prepared by emulsion polymerization. Monomers used were n-butyl acrylate(BA), acrylonitrile (AN), butyl methacrylate(BMA), glycidyl methacrylate(GMA), and acrylic acid (AA). Emulsifiers used were sodium lauryl sulfate and polyoxyethylene lauryl ether, which are an anionic emulsifier and a nonionic emulsifier respectively. Potassium persulfate was used as an initiator and polyvinyl alcohol was used as a stabilizer. Emulsion polymerization was carried out in a semi-batch reactor at $70^{\circ}C$ and agitation speed was kept at 200 rpm. Water resistance, heat resistance, acid resistance, alkali resistance and smoke resistance were examined. As a result, when each 0.03 mole of GMA and AA was introduced, the adhesion properties and various above mentioned resistances of the prepared adhesives were satisfied the standard for automobiles.

• Korean Chemical Engineering Research
• /
• 제47권4호
• /
• pp.410-417
• /
• 2009

중간세공크기(mesopore)의 MCM41에 Imidazole을 담지시킨 CP-MS41 고체 입자의 촉매를 사용하여 GMA 용액에 $CO_2$를 흡수시켜 $CO_2$의 흡수기구로부터 GMA와 $CO_2$의 반응속도론을 고찰하였다. 대기압에서 회분식 흡수조를 사용하여 임펠러의 교반속도, 50 rpm, 촉매, 2 g, 반응온도, 60, 70, $80^{\circ}C$, GMA의 농도, $0.1{\sim}3.0kmol/m^3$, 용제, DMA, NMP, DMSO에서 측정한 $CO_2$의 흡수속도와 경막설에 의한 물질수지식을 사용하여 반응속도상수를 구하였다.

• Biotechnology and Bioprocess Engineering:BBE
• /
• 제6권5호
• /
• pp.341-346
• /
• 2001

For the purpose of mass producing Monascus red pigments optimum medium composition and environmental conditions were investigated in submerged flask cultures. The optimum carbon and nitrogen sources were determined to be 30g/L of glucose and 1.5 g/L of monosodium glutamate (MSG). Of the three metals examined, Fe$\^$2+/ showed the strongest stimulatory effect on pigment production and some stimulatory effect was also found in Mn$\^$2+/. Optimum pH and agitation speed were determined to be 6.5 and 700 rpm, respectively. Under the optimum culture conditions batch fermentation showed that the maximum biomass yield and specific productivity of red pigments were 0.20 g DCW/g glucose and, 32.5 OD$\sub$500/g DCW$\^$-1/h$\^$-1/, respectively.

• 한국주조공학회지
• /
• 제13권3호
• /
• pp.248-258
• /
• 1993

A semi-solid alloy in which solid and liquid phase are co-existing is obtained by stirring of A17075 molten metal. A semi-solid alloy is dependent on the corresponding temperature within the solid-liquid range, and the process parameters should be controlled accurately to obtain the homogeneous semisolid alloy. The fabrication possibility of fiber-reinforced aluminum alloy containing $Al_2O_3$ short fibers with vigorous agitation of short fibers were obtained by control of stirring time, solid fraction and impeller speed in extrusion billet fabrication processes. The microstructure to extrusion billet fabricated by low pressure casting was investigated for fiber dispersion state. The relationship between the extrustion force and velocity at hot extrustion, the flow strain and extrusion ratio were theoretically described. The surface defects with lubricants and without lubricant after hot extrusion were investigated. The composites materials after hot extrusion were measured by vickers hardness with extrusion ratio. It has become clear that the secondary working such as hot extrusion was very useful to obtained improved the mechanical properties of metal matrix composites.

• 생명과학회지
• /
• 제12권5호
• /
• pp.570-576
• /
• 2002

천일염에서 분리된 고호염성균인 Hainrcular sp. EH-1 으로부터 amylase 생성을 위한 배양조건을 검토하여 최적조건을 설정하였다. 그 결과는 다음과 같다. 아밀라아제 생산을 위한 배양 조건은 4$0^{\circ}C$, pH 7.5이었으며, 최적 생육배지를 soluble starch 1.5%, yeast extract 1.0%, MgSO$_4$7$H_2O$ 2.0%, KCI 0.1%, NaCl 25%로 조성하여 500 $m\ell$ 삼각 플라스크에 100 $m\ell$ 씩 분주하여 110 rpm/min으로 진탕 배양시켰다. 생육과 효소활성은 9일 배양 후 최대치를 나타내어서, 균의 생육정도와 효소생산 사이에서 증식연관형을 나타내었다.

• 공업화학
• /
• 제3권1호
• /
• pp.119-129
• /
• 1992

Ethyl acetate와 n-butyl acetate의 $25^{\circ}C$에서 알카리 가수분해 반응을 개량된 Lewis cell에서 행하여 화학반응을 수반한 물질전달 속도를 측정하였다. 측정한 물질전달 속도는 교반조의 교반속도에 무관하였고 이온강도 증가에 따라 감소하였으나 화학반응촉진 계수는 일정하였다. 측정한 화학반응 촉진계수를 경막설로부터 얻은 용질의 확산방정식의 근사해로부터 해석하여 ester의 알카리 가수분해반응의 2차 비가역 반응속도 정수를 얻을 수 있었으며, 그 값은 ethyl acetate의 경우 $0.041m^3/kgmol{\cdot}s$, n-butyl acetate의 경우 $0.338m^3/kgmol{\cdot}s$이었다.