• Journal of the Korean Society for Railway
• /
• v.8 no.2
• /
• pp.188-194
• /
• 2005

Aging characteristics of glass fabric/phenolic composites for tilting train subjected to combined environmental aging factors were investigated. A 2.5KW accelerated aging tester with a xenon-arc lamp was used to provide environmental aging factors such as temperature, moisture, and ultraviolet. A series of aging tests were conducted up to 3000 hours and several types of specimens were prepared along the warp direction and the fill direction. Mechanical degradations for tensile, flexural, and shear properties were evaluated as a function of exposure times through a material testing system. Thermal analysis properties such as storage shear modulus, loss shear modulus, and tan 3 were measured through a dynamic mechanical analyzer. Finally exposed surfaces of the composites were examined using a scanning electron microscope. According to the experimental results, mechanical properties and thermal analysis properties of glass fabric/phenolic composites were found to be slightly degraded as a function of exposure times due to combined environmental effects.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.5
• /
• pp.285-297
• /
• 2023

The effects of aging treatment sequence, specifically pre-aging and post-aging, on the microstructure and mechanical properties of Al-Zn-Mg-Cu aluminum alloys has been studied in comparison to symmetrically rolled specimens. In symmetrically rolled specimens, a straight-band precipitation distribution was observed, whereas asymmetrically rolled specimens exhibited a curved-band microstructure of fine precipitates. Notably, the asymmetrically rolled specimens displayed higher strengths. In the case of post-aging, the aging process occurred after rolling, and the dislocations generated during rolling acted as nucleation sites for precipitates during aging. This resulted in the formation of fine precipitates, contributing to improved mechanical properties compared to symmetric rolling. To enhance strength of the Al-Zn-Mg-Cu aluminum alloys, asymmetric rolling proves to be more effective than symmetric rolling, with post-aging showing greater efficacy than pre-aging.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.6
• /
• pp.2412-2420
• /
• 2018

The thermal degradation of low density polyethylene (LDPE) will accelerate the production of carbonyl groups (C=O), which can act as the induced dipoles under high voltage. In this paper, we researched the dielectric properties and space charge behavior of LDPE after thermal aging, which can help us to understand the correlation between carbonyl groups (C=O) and electrical properties of LDPE. The spectra results show that LDPE exhibit obvious thermooxidative reactions when the aging time is 35 days and the productions mainly contain carboxylic acid, carboxylic eater and carboxylic anhydride, whose amount increase with the increasing of aging time. The dielectric properties show that the real permittivity of LDPE is inversely proportional to temperature before aging and subsequently become proportional to temperature after thermal aging. Furthermore, both the real and imaginary permittivity increase sharply with the increasing of aging time. The fitting results of imaginary permittivity show that DC conductivity become more sensitive about temperature after thermal aging. On this basis, the active energies of materials calculated from DC conductivity increase first and then decrease with the increasing of aging time. In addition, the space charge results show that the heterocharges accumulated near electrodes in LDPE change to the homocharges after thermal aging and the mean volume charge density increase with the increasing of aging time. It is considered that the overlaps caused by electrical potential area is the main reason for the increase of DC conductivity.

• Journal of the Korean Society for Heat Treatment
• /
• v.20 no.1
• /
• pp.11-16
• /
• 2007

The fatigue properties of Ti-Ni shape memory alloy wires were investigated. In Ni-rich Ti-Ni shape memory alloys, $Ti_3Ni_4$ precipitates formed by aging treatments are believed to vary the shape memory and mechanical properties. In this study, the effect of aging temperature and aging time on shape memory properties and fatigue life were investigated using Ti-50.9 at% Ni alloy wires. The specimens were solution-treated at 1073 K for 3.6 ks followed by aging at 573 K, 673 K and 773 K for periods between 3.6 ks and 3600 ks. It was found that the fatigue life under a constant stress decreased with increasing aging temperature. When the specimens were aged at 573 K for periods between 36 ks and 360 ks, superior shape memory and fatigue properties were obtained. The fatigue life also decreased when the test temperature and strain amplitude increased. It was concluded that the fatigue life exhibited a linear relationship with the critical stress for slip.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.3
• /
• pp.588-594
• /
• 2013

Under the condition of Baader aging, the chemical composition variation and the influence of transformer oil aging on electrical properties such as dielectric loss factor and physic-chemical properties such as interfacial tension were studied in the aging precess. Moreover, the correlation between hydrogenated transformer oil electrical and physic-chemical properties and its chemical composition variation were also investigated. The results show that these parameters of physic-chemical and electrical properties of hydrogenated transformer oil relate to each other and have closed correlation with chemical composition.

• Journal of Powder Materials
• /
• v.13 no.3 s.56
• /
• pp.172-177
• /
• 2006

Aging characteristics and mechanical properties of commercial 7xxx series Al composites were investigated from viewpoint of ceramic contents. After sintering process, sintered densities of blended and composite powder were 95 and 97%, respectively. Each part was solution-treated at $475^{\circ}C$ for 60 min and aged $175^{\circ}C$. And two-step aging was also performed form $120^{\circ}C$ to $175^{\circ}C$. The aging behavior of the sintered composite pow-der was different from that of sintered blended powder. The peak aging time of the composite was rapid as well due to strain. Before aging, mechanical properties of sintered composite powder was significantly higher than that of sintered blended powder. These increments of properties were directly affected by ceramic particles. However, after aging, incremental rate of mechanical properties was slowed in the composite.

• Food Science of Animal Resources
• /
• v.40 no.2
• /
• pp.286-296
• /
• 2020

This study investigates the utilization of an electric-field-induced super cooling system in long-term dry aging of beef loin. Analyzed quality properties of dry-aged beef loin applied with electric field refrigeration (EFR) versus commercial refrigeration (CR). Quality properties was including aging loss, pH, water holding capacity (WHC), cooking loss, color, warner-bractzler shear force (WBSF), total plate count (TPC), and thiobarbituric acid reactive substances (TBARS). Aging loss of wk 1 EFR was significantly lower than CR (p<0.05). pH of EFR was slow change tendency compared CR. WHC of both aging methods were higher with increase in aging duration. Cooking loss of wk 1, 2, 4, and 10 EFR were significantly lower than CR (p<0.05). Lightness and redness of EFR was slow change tendency compared CR. However, yellowness of EFR was increased until wk 2, 3, and significantly decreased at wk 10 (p<0.05), but yellowness of CR was decreased until wk 3 and significantly increased with an increasing aging weeks (p<0.05). Both aging methods of WBSF was decreased with increase in aging weeks; however, wk 10 of CR was significantly lower than EFR (p<0.05). TPC after wk 3 EFR groups were significantly lower than CR groups (p<0.05), and TBARS of EFR groups were significantly lower than CR (p<0.05). The present results show that application of the EFR system for dry aging beef loin can extends its shelf life and induce changes of several aging properties in similar to commercial aging.

• Journal of the Korean Society for Heat Treatment
• /
• v.32 no.2
• /
• pp.57-60
• /
• 2019

The impact of two-step treatment on the mechanical properties of the 6061 Al alloy was investigated by testing the hardness and electrical conductance values. After two-step aging treatment, the hardness and electrical conductivity of the alloy was increased, and if the first aging treatment temperature was lower than the secondary aging treatment temperature, both the hardness and the electrical conductivity were not increased. The higher the temperature of the first aging treatment, the higher the hardness. The temperature of the first aging treatment is $175^{\circ}C$, $150^{\circ}C$, $120^{\circ}C$, and the second is $175^{\circ}C$ and $120^{\circ}C$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.255-257
• /
• 2001

In this paper, the silicon rubber insulator for transmission line was experimented for 1,000 hours aging test in salt-fog condition. To evaluate and examine the aging properties of silicon rubber insulator for test, the leakage current of surface was measured. Also hydrophobicity and scanning electron microscopy were compared with initial and aged sample respectively Above results, we can confirm that the surface properties of silicon rubber insulator easily aged by salt-fog condition.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.11
• /
• pp.1178-1182
• /
• 2012

The organic linings at flue gas desulfurization systems (FGD system) in power plant have the excellent chemical properties but, lose the anticorrosive properties according to the aging with environment conditions. The properties of the organic linings depend on the manufacturing company. Therefore, the basic properties of organic linings for the preestimate of life time should be examined by conducting the aging and the bond strength test according to temperature. The pre-aging samples were compared with the post-aging samples. The temperature conditions of the aging process were 70, 150 and $200^{\circ}C$. The bond strength was calculated and the cross sections of fracture surface were examined by optical microscope and SEM. The $T_g$ was examined by DSC, DTA and TGA.