• Journal of the Korean Society for Heat Treatment
• /
• v.10 no.4
• /
• pp.255-265
• /
• 1997

Precipitation and strengthening mechanisms in squeeze cast Mg-8.5wt%Li-4.5wt%Al have been investigated by differential scanning calorimetry(DSC), scanning electron microscopy(SEM), in-situ and ex-situ X-ray diffraction analysis and hardness measurement. Special emphasis was placed on the investigation of the precipitation behavior by the DSC technique. Microstructural and calorimetric analysis showed that ${\theta}$ and ${\delta}$ precipitates in the b.c.c. ${\beta}$ phase matrix, forming two exothermic peaks at the temperature ranges of $130^{\circ}C{\sim}180^{\circ}C$ and $236^{\circ}C{\sim}280^{\circ}C$. ${\theta}$ and ${\delta}$ dissolve into the matrix forming an endothermic peak at the temperature range of $280^{\circ}C{\sim}352^{\circ}C$. The as-cast microstructure consists of ${\alpha}$, ${\beta}$ and ${\delta}$. Peak strength was obtained after aging for 1 hour at $50^{\circ}C$. The aging time required for the peak strength decreased as the aging temperature increases. The hardness decrease during overaging was due to the coarsening of ${\theta}$ precipitates. Microhardness measurement showed that variation of the hardness of ${\beta}$ matrix was more pronounced than that of the ${\alpha}$ phase, indicating that the ${\beta}$ phase is more responsible for the strengthening of the Mg-8.5wt%Li-4.5wt%Al alloy.

• Korean Journal of Materials Research
• /
• v.18 no.1
• /
• pp.38-44
• /
• 2008

The micro-structural changes, strength characteristics, and micro-fractural behaviors at the joint interface between a Sn-4.0wt%Ag-0.5wt%Cu solder ball and UBM treated by isothermal aging are reported. From the reflow process for the joint interface, a small amount of intermetallic compound was formed. With an increase in the isothermal aging time, the type and amount of the intermetallic compound changed. The interface without an isothermal treatment showed a ductile fracture. However, with an increase in the aging time, a brittle fracture occurred on the interface due mainly to the increase in the size of the intermetallic compounds and voids. As a result, a drastic degradation in the shear strength was observed. From a microshear test by a scanning electron microscope, the generation of micro-cracks was initiated from the voids at the joint interface. They propagated along the same interface, resulting in coalescence with neighboring cracks into larger cracks. With an increase in the aging time, the generation of the micro-structural cracks was enhanced and the degree of propagation also accelerated.

• KIEAE Journal
• /
• v.7 no.5
• /
• pp.35-40
• /
• 2007

The purpose of this study is to execute evaluation experiment to know the evaluation property of lighting environment of residential space for senior people, considering visual characteristics along aging, and finally provide basic data for the lighting plan to ensure the visual amenity. Processes of this study are as follows;1) Analyzed the variation property of visual sensibility and visual ability of senior people along aging. 2) Selected 3 types of life behavior(rest, conversation and reading) after checking life behavior in residential space for senior people based on advanced study. 3) Made the Mock-up Model that Dimming is possible, actual furnace to model. 4) Executed sensitivity evaluation experiment about lighting environment. 5) Analyzed evaluation property of lighting environment of residential space for senior people. Results of this study are as follows, 1) With lens-filter, we got comfort and amenity in bulb-color lamp which has similar color temperature with red of lens filter. 2) Lighting environment tests during conversation : With lens filters, they felt comfort on bulb color in case of higher illuminance than 850lux and daylight color in 500lux. 3) Lighting environment tests at reading : With lens filter, bulb color got better score in brightness and appropriateness than daylight color.

• Journal of the Korean Electrochemical Society
• /
• v.3 no.3
• /
• pp.162-168
• /
• 2000

The influence of phenolsulfunate concentrations on electroplating characteristics and electrochemical behaviors was investigated with a viewpoint of electrolyte aging using the circulation cell and potentiostate And comparison of tinplate coating appearance such as glossiness and Image clarify has been also studied with varying of phenolsulfonic acid (PSA) solutions. As the aging of electrolyte proceeded, the limiting current density was moved to a lower current density region by the limitation of mass transfer, and higher phenolsulfunate concentrations resulted in the narrower optimum current density range and deterioration of coating surface of tinplates. The difference of the limiting current density was not remarkable with increasing electrolyte temperature. Thus the electrolyte aging was attributed to the limitation of thermally-activated process such as mass transfer of reducible ions. It has also been considered that the accumulation of phenolsulfonate suppressed normal electrotinning reaction by reducing the mobility of stannous ions, taking into account of the smaller effect of electrolyte aging. Experiments showed similar polarization behavior between the electrolyte of high phenolsufonate solution and the aged one, which comes to conclude that the accumulation of phenolsulfonate is one of the major causes of electrolyte aging.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.4
• /
• pp.123-129
• /
• 1999

Although type 316 stainless steel is widely used such as in reactors of petrochemical plants and pipes of steam power plants and s attracting attention as potential basic material for the fast breeder reactor structure alloys in nuclear power plants and is attracting attention as potential basic material for the fast breeder reactor structure alloys in nuclear power plants the effect of precipitates which form during the long term exposure at service temperature on creep properties is not known sufficiently. In this study to investigate the creep properties and the influence of prior aging on the microstructure to form precipitates specimens were first solutionized at 113$0^{\circ}C$ for 20 minutes and then aged for different times of 0 hr, 100 hrs, 1000 hrs and 2200 hrs at 75$0^{\circ}C$ After heat treatments tensile tests both at room temperature and $650^{\circ}C$ and constant load creep ruptuere tests were carried out.

• Journal of Mechanical Science and Technology
• /
• v.18 no.10
• /
• pp.1730-1737
• /
• 2004

The BI (Ball Indentation) method has the potential to assess the mechanical properties and to replace conventional fracture tests. In this study, the effect of aging on mechanical behavior of 1Cr-1Mo-0.25V steels procured by isothermal aging heat-treatment at four different aging times in the range of 0～1820 hours at 630$^{\circ}C$, were investigated using BI system.

• Asia Marketing Journal
• /
• v.18 no.4
• /
• pp.139-160
• /
• 2017

Despite widespread awareness of the importance of a middle-aging and older consumer market, it is surprising that very little research has been conducted on their in-home shopping behavior. Therefore, this study focused on middle-aging and older female television home shoppers and examined the effects of persuasive mentions of the show host and parasocial interaction on social involvement, perceived loneliness, mood, perceived risk and unplanned buying tendency. A total of 109 middleaged and older female television shoppers responded. Results of path analysis revealed that persuasive mentions did not influence parasocial interaction. However, as middle-aging and older consumers more para-socially interacted with the host, they were likely to use television shopping for alleviating loneliness. Practical and theoretical implications were discussed.

• Elastomers and Composites
• /
• v.53 no.4
• /
• pp.213-219
• /
• 2018

The degradation mechanism and physical properties of an FKM O-ring were observed with thermal aging in this experiment. From X-ray photoelectron spectroscopy (XPS) analysis, we could observe carbon (285 eV), fluoro (688 eV), and oxygen (531 eV) peaks. Before thermal aging, the concentration of fluoro atoms was 51.23%, which decreased to 8.29% after thermal aging. The concentration of oxygen atoms increased from 3.16% to 20.39%. Under thermal aging, the FKM O-ring exhibited debonding of the fluoro-bond by oxidation. Analysis of the C1s, O1s, and F1s peaks revealed that the degradation reaction usually occurred at the C-F, C-F2, and C-F3 bonds, and generated a carboxyl group (-COOH) by oxidation. Due to the debonding reaction and decreasing mobility, the glass transition temperature of the FKM O-ring increased from $-15.91^{\circ}C$ to $-13.79^{\circ}C$. From the intermittent CSR test, the initial sealing force was 2,149.6 N, which decreased to 1,156.2 N after thermal aging. Thus, under thermal aging, the sealing force decreased to 46.2%, compared with its initial state. This phenomenon was caused by the debonding reaction and decreasing mobility of the FKM O-ring. The S-S curve exhibited a 50% increase in modulus, with break at a low strain and stress state. This was also attributed to the decreasing mobility due to thermal aging degradation.

• Macromolecular Research
• /
• v.12 no.6
• /
• pp.608-614
• /
• 2004

Isotactic polypropylene (PP) surfaces were modified with argon and oxygen plasmas using a radio­frequency (RF) glow discharge at 240 mTorr and 40 W. The changes in topography and surface structure were investigated by atomic force microscopy (AFM) in conjunction with specular reflectance of infrared (IR) microspectroscopy. Under our operating conditions, the AFM image analysis revealed that longer plasma treatment resulted in significant ablation on the PP surface, regardless of the kind of plasma employed, but the topography was dependent on the nature of the gases. Specular reflectance IR spectroscopic analysis indicated that the constant removal of surface material was an important ablative aspect when using either plasma, but the nature of the ablative behavior and the resultant aging effects were clearly dependent on the choice of plasma. The use of argon plasma resulted in a negligible aging effect; in contrast, the use of oxygen plasma caused a noticeable aging effect, which was due to reactions of trapped or isolated radicals with oxygen in air, and was partly responsible for the increased surface area caused by ablation. The use of oxygen plasma is believed to be an advantageous approach to modifying polymeric materials with functionalized surfaces, e.g., for surface grafting of unsaturated monomers and incorporating oxygen-containing groups onto PP.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.1
• /
• pp.37-43
• /
• 2009

In this study, the physical properties of base paper for the manufacture of mulching mat for afforestation seedling were investigated. The base paper for mulching mat was prepared by stock conditions of PAE and AKD addition into the screened slurry of KOCC for the strengthening effects of wet tensile and burst strength. The optimum additions of PAE and AKD were considered at 2% and 0.5%, respectively. The accelerated aging by ISO 5630-1 and wet heat aging method under hot water for 2 kinds of commercial mulching and wet strength paper were compared with the base paper prepared for mulching mat manufacture. The accelerated aging test for the base paper prepared for mulching mat manufacture resulted in the same tendency of physical properties as two kinds of commercial products. However, the results of wet heat aging test under hot water indicated that the physical strength for base paper prepared was much higher than others. In addition, the opacity behavior for base paper prepared was enough effects to obstruct weeds growth by isolating transmission of sunlight.