• Journal of the Korean Recycled Construction Resources Institute
• /
• v.5 no.3
• /
• pp.275-281
• /
• 2017

This study is to investigate experimentally the effect of refining of fly ash (FA) on the engineering properties of the cement mortar. Five different FAs are used including raw fly ash, refined fly ash, reject ash and their two different combinations. The cement mortars are fabricated with 1:1(binder to fine aggregate), 1 : 3 and 1 : 5 respectively, which are replaced 30% of FA by cement. Test results, indicated that, the flow of Ra showed lower flowability than Rf at all mixing ratios. Also in the case of Rj, it was expected to show low fluidity, but it showed flowability equal to or higher than Rf. Air contents are all formulations except Rf and Rj did not satisfy the target range. Using Ra, the refining process shows an air amount about 41% lower than Rf, in the case of Rj, it showed about 19% higher air content than Rf due to porous foreign matters inside the mortar. Compressive strength was in the early days 3 and 7, the strength was lower than that of Plain's OPC, after 28 days Rf exerts higher strength than other FAs, it was confirmed that higher strength than OPC can be secured at a mixing ratio of 1: 1 and 1: 3. For frost resistance, the use of unrefined FA resulted in decrease of frost resistance sharply due to loss of air content by the use of unrefined FA. Therefore, it is considered that the use of high quality FA through refining process will contribute positively to the economical formulation of concrete and the stability of the structure.

• Journal of Bio-Environment Control
• /
• v.16 no.3
• /
• pp.228-232
• /
• 2007

We have also clarified the effects of the different substrates; (perlite, peatmoss and granular rock-wool) on the plant growth and the mineral contents of Campanula takesimana until 70 days after transplanting. Overall plant growth in terms of plant height, stem diameter, number of leaves, root length, fresh and dry weight of shoot and root were increased in the order of that mixed perlite and peat moss (50 : 50, v/v)>peat moss (100%)>perlite (100%)>granular rock wool (100%). Mineral contents in plants were much more in the order of potassium $(15.38-43.91cmol^+/kg)$, calcium $(5.48-7.78cmol^+/kg)$, magnesium $(4.38-6.55cmol^+/kg)$ and sodium $(1.25-1.69cmol^+/kg)$. The higher mineral contents of plants were also most made in the mixed substrates of perlite and peat moss (50 : 50, v/v).

• Journal of Korean Society of Forest Science
• /
• v.105 no.2
• /
• pp.223-230
• /
• 2016

This study was carried out to investigate the quarrying and restoration characteristics on quarry in Korea. We researched quarrying and restoration status, analyzed the relationship between restoration area and permitted period, permitted area, quarrying volume, pit slope width, height, and berm width from 55 quarry sites. Most of the quarries were located in the following conditions : mixed forest, average altitude of less than 300 m, average mountain slope of $61^{\circ}$<, hillside, granite and landslide hazard class. Major quarrying characteristics were permitted period of 6~10 years, permitted area of less than 10 ha, quarrying volume of less than $1,000,000m^3$, a stone type of aggregate, a quarrying type of terrace, pit slope of $61^{\circ}$< Most quarries were restored by themselves, and the main restoration type was slope greening. Also, area ratio of flatland, pit slope, and berm was 54.9:39.6:5.5. Ccorrelation analysis showed that quarrying area was positively correlate with quarrying volume (${\alpha}=0.01$), permitted area, pit width, and pit height (a=0.05).

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.4
• /
• pp.91-98
• /
• 2009

Recently, production cost of ready mixed concrete has been increased due to the rising cost of raw materials such as cement and aggregate etc. cause by the upturn of oil price and increase of shipping charge. The delivery cost of ready mixed concrete companies, however, has been decreased owing to their excessive competition in sale. Consequently, ready mixed concrete companies began to manufacture the concrete by mixing ground granulated blast furnace slag(GGBF) and fly-ash in order to lower the production cost. Therefore, the objective of this study was to predict 28 days strength of GGBF slag concrete by early strength(warm and hot water curing method) for the sake of managing with ease the quality of ready mixed concrete. In experimental results, the prediction equation for 28 days compressive strength of GGBF slag concrete could be produced through the linear regression analysis of early strength and 28 days strength. In order to acquire the reliability, all mixture were repeated as 3 times and each mixture order was carried out by random sampling. The prediction equation for 28 days strength of GGBF slag concrete by 1 day compressive strength(accelerated testing) according to warm and hot water curing method won the good reliability.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.1
• /
• pp.101-109
• /
• 2009

This CW(Construction wastes) are increasing as construction industry is growing, so many countries make efforts to recycle CW. Korea also made a stipulation for recycling CW. But the main content of this stipulation is for using recycled aggregates. Advanced countries try to increase reuse rate of not only recycled aggregate but also other kinds of wastes. So they are adopting SDM(separating dismantlement) method and we are also planning to make the system for SDM. This study is about SDM analysis through construction field investigation and difference analysis between SDM and UDM comparing predictive amount by UDM with real generated amount by SDM. First, the generated amount of construction wastes by SDM is more than estimated amount by UDM, and mixed waste was specially reduced more than UDM. The warehouse is easier than the office building to applicate SDM. But still there is no manual for SDM in the site, so establishment of SDM is demanded.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.1
• /
• pp.103-110
• /
• 2011

This study is to comparatively analyze the characteristics of pH decrease in recycled fine aggregates for embankment and landfill produced from waste concrete by using natural process and artificial process. The result was as follows In case of recycled fine aggregates left outdoor, it was found that pH level was decreased if the thickness of embankment becomes thinner, or the materials left outdoors owing to high concentration of $CO_2$ in atmosphere caused by respirations of people. When the air was permeated, pH level was decreased more effectively. It was analyzed that this phenomenon was caused by efficient supply of $CO_2$ in the recycled fine aggregates owing to high-pressure ventilators. In case of water spraying treatment, sprayed water facilitated hydration of unhydrated cement to dissolve calcium hydroxides which neutralized $CO_2$ in the atmosphere during desiccation process and decrease pH level by a considerable margin. In case of Immersed treatment, decrease of pH was not sufficient. When facilitating the supply of $CO_2$, pH level of the recycled fine aggregates was decreased by the largest margin. It was analyzed that this phenomenon was caused by efficient supply of $CO_2$. From the above results, it was analyzed that the most effective method of reducing pH level of the recycled fine aggregates from the aspects of pH reduction performance, economic efficiency and workability was repeated wet-dry cycles of spraying water to the aggregates in the proportion of 1:0.5 by weight and then treating by forcefully blowing $CO_2$ gas into the aggregates.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.1
• /
• pp.128-135
• /
• 2011

In this study, in order to develop ultra rapid hardening mortar(URHM) for tunnel repairs using bottom ash of low recycle ratio and Admixture as Eco concept, fundamental properties of URHM on temperature condition of construction field were performed. Test result, URHM of three types for fluidity and setting time were as in the following : B > C > A. Those for low temperatures were later than the standard condition. Compressive, bending and bond strength were similar with three types as follow. In compressive strength, initial strength of the low were smaller than the standard but the low in the long-term were similar with the standard. On the contrary to this, bending strength were similar in initial strength but the low in the long-term were smaller than the standard. The low in bond strength was average 35% less than the standard. Length changes was as in the following : A > C > B. the low is two times much as the standard but the case using blast furnace slag particles noticeably reduced length changes. Water absorption coefficient and water vapor resistance were as in the following : C > A > B. In case of URHM added bottom ash, water absorption coefficient and water vapor resistance were increased because bottom ash is porous material.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.4
• /
• pp.404-417
• /
• 2016

The purpose of this study is to examine the extent to which the deterioration in strength of high strength concrete of 60MPa replaced by a large amount of recycled coarse aggregates (more than 60% to 100% of replacement ratio) could be recovered with steel fiber reinforcement through material compressive strength test and shear failure test on short and middle beams and then to offer useful data for aggregate supply system of a sustainable resource circulation type. This study first examined the results of previous related tests. The results of the material compressive strength tests confirmed that when using a combination of steel fiber reinforcements of volumn ratio 0.75% and high quality recycled coarse aggregates with an water absorption rate within 2.0%, the strength characteristics of high strength concrete of 60MPa level were not only restored to the strength level of concrete made with natural aggregates, but also showed superior ductility. And the shear failure tests on short and middle beams using recycled coarse aggregates more than 60% with shear span to depth ratio (a/d) of 2 and 4 controlled by shear forces mainly confirmed that effects of superior shear strength increase and ductile behavior characteristics were showed by steel fiber reinforcements.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.3 no.2
• /
• pp.152-158
• /
• 2015

In order to investigate the feasibility of stone dust sludge as fine aggregate, an experimental study was performed on cement mortar with stone dust sludge. fresh mortar properties and strength with various stone dust sludge replacement ratios were estimated. the replacement ratio adopted in this study was 0, 10, 20, 30%. Flow, air content, and rheological properties were considered as properties of fresh mortar. Compressive strength and flexural tensile strength were measured for strength. The results are as follows. Higher amount of stone dust sludge caused reduction in slump and air content. In the rheological properties, both yield stress and plastic viscosity increased as stone dust sludge content increased up to 20% replacement ratio, but there were no remarkable difference between 20 and 30%. Yield stress increased drastically between 10 and 20%. Compressive and flexural tensile strength results indicated that the strength variation was not significant according to stone dust sludge content, but the strength gain in the early age by adding stone dust sludge was evident. the strength at the age of 28 days however did not show noticeable effect of adding stone dust sludge.

• Resources Recycling
• /
• v.26 no.2
• /
• pp.66-70
• /
• 2017

The purpose of this research was to estimate density changes of sea sand by washing. To examine water content test, field density test, particle density test and measuring of dump regarding extracted sea sand and selling one. Measured result of mean particle density of barge and dump were $2.666g/cm^3$, $2.651g/cm^3$, respectively. Also, measured result of field density for each sea sand was $1.716g/cm^3$, $1.331g/cm^3$ on average. Converted to the volume of 1ton of each sea sand, $0.583m^3$, $0.751m^3$, respectively. Occurring to volume change approximately 28.8% on average. The mean field densities of measuring of sea sand that dump and barge were $1.398g/cm^3$ and $1.716g/cm^3$ respectively. This values indicated $0.715m^3$ and $0.583m^3$ each, when converted to the volume of sea sand 1ton. It was found that the average of 22.6% volume change occurred between the amount of sea sand and the sales volume.