• Journal of the Korean Ceramic Society
• /
• v.45 no.10
• /
• pp.610-617
• /
• 2008

Multi-walled carbon nanotube(CNT) reinforced hydroxyapatite composite coating with a thickness of $5{\mu}m$ has been successfully deposited on Ti substrate using aerosol deposition(AD). The coating had a dense microstructure with no cracks or pores, showing good adhesion with the Ti substrate. Microstructural observation using field-emission scanning electron microscopy(FE-SEM) and transmission electron microscopy(TEM) showed that CNTs with original tubular morphology were found in the hydroxyapatite-CNT(HA-CNT) composite coating. Measurements of hardness and elastic modulus for the coating were performed by nanoindentation tests, indicating that the mechanical properties of the coating were remarkably improved by the addition of CNT to HA coating. Therefore, HA-CNT composite coating produced by AD is expected to be potentially applied to the coating for high load bearing implants.

• Journal of the Korean Ceramic Society
• /
• v.48 no.5
• /
• pp.439-446
• /
• 2011

Yttria stabilized zirconia (YSZ) coating was formed on AA1050 Al alloys by aerosol deposition (AD), and its electrochemical corrosion properties were investigated in 3.5 wt% NaCl and 0.5M $H_2SO_4$ solutions. The crack-free, dense, and ~5 ${\mu}m$ thick YSZ coating was successfully obtained by AD. The as-deposited coating was composed of cubic-YSZ nanocrystallites of ~10 nm size. The potentiodynamic test indicated that the YSZ coated Al alloy had much lower corrosion current densities (2 nA/$cm^2$) by comparison to uncoated sample and exhibited a passive behavior in anodic branch. Particularly, a pitting breakdown potential could not be identified in $H_2SO_4$. EIS tests revealed that the impedance of YSZ coated sample was ${\sim}10^6{\Omega}cm^2$ in NaCl and ${\sim}10^7{\Omega}cm^2$ in $H_2SO_4$, which was about 3 or 4 orders of magnitude higher than that of uncoated sample. Consequently, the corrosion resistance of Al alloy had been significantly enhanced by the YSZ coating.

• Transactions of the Korean hydrogen and new energy society
• /
• v.21 no.4
• /
• pp.271-277
• /
• 2010

$(Ba(Zr_{0.85}Y_{0.15})O_{3-\delta})$ oxide, showing high protonic conductivity at high temperatures and good chemical stability with $CO_2$ are referred to as hydrogen separation membrane. For high efficiency of hydrogen separation ($H_2$ flux and selectivity) and low fabrication cost, ultimate thin and dense BZY-Ni layer has to be coated on a porous substrate such as $ZrO_2$. Aerosol depostion (AD) process is a novel technique to grow ceramic film with high density and nano-crystal structure at room-temperature, and may be applicable to the fabrication process of AD integration ceramic layer effectively. XRD, SEM, X-ray mapping measurements were conducted in order to analyze the characteristics of BZY-Ni membrane fabricated by AD process. it is observed that it is homogeneous distribution for BZY-Ni. The result of $H_2$ permeation rate suggests that BZY-Ni composite is higher than BZY.

• Particle and aerosol research
• /
• v.5 no.2
• /
• pp.83-90
• /
• 2009

This paper describes a condensation-evaporation method (CEM) to produce size-controlled spherical silver nanoparticles by perturbing coagulation and coalescence processes in the gas phase. Polydisperse silver nanoparticles generated by the CEM were first introduced into a differential mobility analyzer (DMA) to select a group of silver nanoparticles with same electrical mobility, which also enables to make a group of nanoparticles with elongated structures and same projected area. These silver nanoparticles selected by the DMA were then in-situ sintered at ${\sim}600^{\circ}C$, and then they were observed to turn into spherical shaped nanoparticles by the rapid coalescence process. With the assistance of modified converging-typed quartz reactor, we can also produce the 10 times higher number concentration of silver nanoparticles compared with a general quartz reactor with uniform diameter. Finally, the spherical silver nanoparticles with 30 nm were electrostatically deposited on the surface of silicon substrate with the coverage rate of ~4%/hr. This useful preparation method of size-controlled monodisperse silver nanoparticles developed in this work can be applied to the various studies for characterizing the physical, chemical, optical, and biological properties of nanoparticles as a function of their size.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.224-224
• /
• 2008

고주파용 집적회로 기판소재로의 응용을 위해 세라믹 특유의 취성을 개선한 $Al_2O_3$-polyimide 복합체 후막을 에어로졸데포지션법을 이용해 제조하고 그 특성을 평가하였다. 그 결과 기공이 거의 없이 치밀한 구조를 갖는 $Al_2O_3$-polyimide 복합체 후막이 구리 및 유리 기판 상에 성막 되었음이 SEM 및 EDS을 통해 확인되었다. 상용 $Al_2O_3$ 출발 파우더를 사용한 복합체 제조시 1 MHz에서 유전율은 6.7, 유전 손실률은 0.026 이었다. 유전특성의 향상을 위하여 에어로졸데포지션법으로 성막된 $Al_2O_3$-polyimide 복합체 후막의 후속 열처리 결과 유전손실율이 0.026에서 0.007로 감소하였다. 또한 집적회로 기판소재로의 응용을 위한 저온화 제조공정 확립을 위하여 $Al_2O_3$ 출발 파우더의 공정 전 열처리 후 상온에서 성막한 경우에도 어떠한 후속 열처리 없이 유전손실률이 0.007로 감소하였다.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.319-322
• /
• 1989

Using pyrosol method, based on the pyrolysis of an aerosol produced by ultrasonic spraying, the deposition of transparent conducting oxides (TCO) such as $In_2O_3$ : Sn, $SnO_2$ : Sb and $SnO_2$ : F on glass substrates was studied. The electrical, optical and structural properties as functions of substrate temperature, dopant concentration, substrate type and carrier gas type were investigated.

• Korean Journal of Materials Research
• /
• v.21 no.5
• /
• pp.277-282
• /
• 2011

Negative temperature coefficient (NTC) materials have been widely studied for industrial applications, such as sensors and temperature compensation devices. NTC thermistor thick films of $Ni_{1+x}Mn_{2-x}O_{4+{\delta}}$ (x = 0.05, 0, -0.05) were fabricated on a glass substrate using the aerosol deposition method at room temperature. Resistance verse temperature (R-T) characteristics of the as-deposited films showed that the B constant ranged from 3900 to 4200 K between $25^{\circ}C$ and $85^{\circ}C$ without heat treatment. When the film was annealed at $600^{\circ}C$ 1h, the resistivity of the film gradually decreased due to crystallization and grain growth. The resistivity and the activation energy of films annealed at $600^{\circ}C$ for 1 h were 5.203, 5.95, and 4.772 $K{\Omega}{\cdot}cm$ and 351, 326, and 299 meV for $Ni_{0.95}Mn_{2.05}O_{4+{\delta}}$, $NiMn_2O_4$, and $Ni_{1.05}Mn_{1.95}O_{4+{\delta}}$, respectively. The annealing process induced insulating $Mn_2O_3$ in the Ni deficient $Ni_{0.95}Mn_{2.05}O_{4+{\delta}}$ composition resulting in large resistivity and activation energy. Meanwhile, excess Ni in $Ni_{1.05}Mn_{1.95}O_{4+{\delta}}$ suppressed the abnormal grain growth and changed $Mn^{3+}$ to $Mn^{4+}$, giving lower resistivity and activation energy.

• Korean Journal of Materials Research
• /
• v.9 no.5
• /
• pp.478-483
• /
• 1999

The effects of the composition on the consolidation temperature and refractive index of the glass thin film fabricated by aerosol flame deposition method in SiO$_2$-B$_2$O$_3$-CaO-P$_2$O\ulcorner system were investigated. When the amount of CaO was constant in SiO$_2$-B$_2$O$_3$-CaO system the consolidation temperature of glass thin film decreased with increasing the amount of B$_2$O$_3$. Also, when the amount of SiO$_2$ and B$_2$O$_3$ was constant the consolidation temperature of glass thin film increased with increasing the amount of CaO. P$_2$O\ulcorner was added to 72.5SiO$_2$-25B$_2$O$_3$-2.5CaO in order to decrease its consolidation temperature. As the amount of P$_2$O\ulcorner increased its consolidation temperature decreased and the refractive index linearly increased from 1.4649 to 1.4684. When the amount of CaO and P$_2$O\ulcorner was constant in SiO$_2$-B$_2$O$_3$-CaO-P$_2$O\ulcorner system the consolidation temperature of glass thin film decreased with increasing the ratio of SiO$_2$/B$_2$O$_3$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.210-210
• /
• 2008

에어로졸 증착법은 상온에서 다양한 기판 상에 고밀도의 세라믹 후막을 코팅할 수 있는 최신 기술로써 다양한 방면으로의 응용이 개대되고 있다. 본 실험에서는 ADM을 이용하여 고주파수 영역에서 사용가능한 기판소재 제조에 관한 연구를 진행하였다. ADM을 통해 형성된 $Al_2O_3$ 막의 유전율은 9-10으로 bulk 시료와 비슷한 특성을 보였으나 후막의 손실률의 경우는 bulk 시료에 비해 상당히 컸으며 주파수 증가에 따라 그 값이 크게 감소하는 경향을 보였다. 본 실험에서는 ADM으로 형성된 $Al_2O_3$의 높은 손실률의 원인에 대해 고찰하고 ADM 을 통해 기판소재로 사용가능한 저손실의 $Al_2O_3$막의 제조를 위한 방법을 제시하고자 하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.117-117
• /
• 2010

나노입자 제조 기술이 점차 발전하면서 금속산화물, 반도체용 및 태양전지용, 신소재 등 다양한 응용분야에 사용하고 있다. 따라서 이와 같은 나노입자 제조방법으로는 펄스 레이저 용사법(pulsed laser ablation), 플라즈마 아크 합성법(plasma arc synthesis), 열분해법(pyrolysis), plasma-enhanced chemical vapor deposition (PECVD)법 등과 같은 기상공정이 많이 사용되고 있다. 기상공정은 기존의 공정에 비해 고순도 입자의 대량 생산, 다성분 입자의 화학적 균질성 유지, 비교적 간단하고 깨끗한 공정 등의 장점을 가지고 있다. 기상공정에서 일반적인 입자 형성 메커니즘은 기체 상태의 화학 물질이 물리적 공정 혹은 화학 반응에 의해 과포화상태에 도달하게 되며, 이 때 동질 핵생성(homogeneous nucleation)이 일어나고 생성된 핵(nuclei)에 기체가 응축되고 충돌, 응집하면서 입자는 성장하게 된다. 열분해법은 실리콘 나노입자를 생산하는 기상공정 중 하나이다. 일반적으로 열분해 공정은 지속적으로 열이 가해지는 반응기 내에 반응기체인 $SiH_4$을 주입하고, 운반기체는 He, $H_2$, Ar, $N_2$ 등을 사용하였을 때, 높은 열로 인해 $SiH_4$가 분해되며, 이 때 가스-입자 전환 현상(gas to particle conversion)이 일어나 실리콘 입자가 형성된다. 그러나 입자 형성과정은 $SiH_4$ 농도, 유량, 작동 압력, 온도 등 매우 다양한 요소에 영향을 받는다. 고, 복잡한 화학반응 메커니즘에 의해 명확히 규명되지는 못하고 있다. 이에 본 연구에서는 복잡한 화학반응을 해석하는 상용코드 CHEMKIN 4.1.1을 이용하여 열분해 반응기 내에서의 실리콘 입자 형성, 성장, 응집, 전송 모델을 만들고 이를 수치해석하였다. 표면 반응, 응집, 전송에 의한 입자 성장 메커니즘을 포함하고 있는 aerosol dynamics model을 method of moment법으로 해를 구하였으며, 이를 실험 결과와 비교하여 모델링을 검증하였다. 또한 반응기의 온도, 압력, 가스 농도, 유량 등의 요소를 고려하여 실리콘 나노입자를 형성하는 최적의 조건을 연구하였다.