• Elastomers and Composites
• /
• 제8권2호
• /
• pp.140-147
• /
• 1973

The influence of the adhesive force test conditions on the resultant adhesive force was measured using a chloroprene rubber as an adhesive and a plywood as an adherent. It was clarified from the experiments which adhesive force test conditions could influence strongly the adhesive force. After this, the constant values neccessary as the test conditions of the adhesive force in making generally a test of the adhesive force determined.

• Journal of Pharmaceutical Investigation
• /
• 제23권1호
• /
• pp.51-53
• /
• 1993

Mucoadhesive tablets containing hydroxypropylcellulose-H (HPC) and carbopol 934 (CP) were prepared from direct compression. Their adhesive forces and water absorptions were investigated by using mouse peritoneal membrane and 1.5% agar plate, respectively. Adhesive force was significantly improved with increasing CP concentration, but was not affected by compression force and addition of disintegrants. And adhesive force to mouse peritioneal membrane was increased as fixing time increased. In conclusion, adequate adhesive force can be obtained by control of CP/HPC ratio and fixing time.

• The Journal of Advanced Prosthodontics
• /
• 제4권2호
• /
• pp.97-102
• /
• 2012

Study was conducted to determine and assess the effect of different type of denture adhesives on the incisal bite force of complete denture wearers until the dislodgement of upper denture, using pressure transducer. MATERIALS AND METHODS. 30 patients out of 100 were included in the study. Based on the Kapur's method of scoring denture retention and stability, these patients were divided into 3 groups-Group A - Clinically good dentures; Group B - Clinically fair dentures; and Group C - Clinically poor dentures. A custom made occlusal force meter was constructed based on the load cell type of pressure transducers. Different adhesives (powder, paste and adhesive strips) were used in the study. Complete denture wearers were asked to bite on the load cell and the readings of incisal bite force were recorded. The readings of incisal bite force were subjected to statistical analysis using Repeated measures ANOVA followed by post-hoc bonferroni test. RESULTS. The result suggests that denture adhesives improved the incisal bite force of complete denture wearers significantly The incisal bite force (in kg) in Group A without using adhesives, with powder adhesive, with paste adhesive and with adhesive strips was found to be 2.48 (${\pm}0.16$), 3.43 (${\pm}0.11$), 6.01 (${\pm}0.11$), 3.22 (${\pm}0.09$) respectively. The incisal bite force (in kg) in Group B without using adhesives, with powder adhesive, with paste adhesive and with adhesive strips was found to be 1.87 (${\pm}0.18$), 3.35 (${\pm}0.14$), 5.34 (${\pm}0.18$), 3.21 (${\pm}0.12$) respectively. The incisal bite force (in kg) in Group C without using adhesives, with powder adhesive, with paste adhesive and with adhesive strips was found to be 1.00 (${\pm}0.17$), 3.07 (${\pm}0.14$), 4.37 (${\pm}0.26$), 2.99 (${\pm}0.14$) respectively. CONCLUSION. Within the limitations of the study, it was concluded that the use of denture adhesive was found to be significantly effective in improving the incisal bite force of complete dentures until the dislodgement of upper denture. Fittydent paste adhesive was found to be more effective than the powder and strips adhesives. The improvement in incisal bite force was found to be higher in Group C in comparison to that of Group A and Group B.

• Tribology and Lubricants
• /
• 제18권4호
• /
• pp.249-254
• /
• 2002

Adhesive contact characteristics of torus-shaped bumps were analyzed using the finite element technique considering the adhesive force. Analyses focused on the effect of rim and bump radii on the adhesive contact behavior such as the jump-to-contact behavior, adhesion hysteresis, pull-off forces, contact region and pressure, and surface and subsurface stresses. Analysis results in the absence of adhesive force were also included to examine the effect of adhesive force. The applicability of torus-shaped bumps to the MEMS structure for reduction of friction is discussed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.641-644
• /
• 2005

The study on the interaction forces of some biological materials is important to understanding biological phenomena and their application to practical purpose. This paper introduces a measuring technique for biological adhesive forces using the AFM(Atomic Force Microscope). Since no standardized thesis on adhesive forces exist, the adhesive forces is defined as adhesive forces against a hardened surface of biological materials. To grant the results are meaningful, which is based on the understanding the surface characteristics of biological materials using the AFM, a nominal value of average adhesive force per unit area should be measured. Therefore the modified AFM probe with small micro glass bead was proposed so that it can guarantee the required contact area for measuring the average adhesive forces. A pyrex glass substrate with circular patterns, which was fabricated by micromachining technique, is introduced in order to controll the contact area. The two types of mussel adhesive proteins, Celltak and recombinant-MGFP5, were tested by the proposed measuring method. The test results show that the adhesive force of the mussel adhesive proteins can be reliably measured by use of this method.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 제35회 춘계학술대회
• /
• pp.179-184
• /
• 2002

Adhesive contact characteristics of torus-shaped bumps, which are commonly used to reduce friction and stiction in hard disks, are analyzed to examine the applicability to the MEMS structure. The analysis is conducted with the finite element technique considering the adhesive force. Torus-shaped bumps of various rim and bump radii are analyzed. The jump-to-contact behavior, adhesion hysterisis, pull-off forces, contact region and pressure, and surface and subsurface stresses are presented and discussed. Analysis results in the absence of adhesive force are also presented to identify the effect of adhesive force.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.1215-1220
• /
• 2004

Cell adhesion to any material surface is considered to be fundamental and important phenomenon in the fields of tissue engineering. Cell adhesion molecules, mechanism, and attachment force have been studied and described a lot. However, the effects of mechanical stimuli on the adhesive forces still have been left much to be investigated. In this study, to investigate the changes in cell adhesive force due to resting time period during the intermittent hydrostatic pressurizing (IHP), cells were cultured under the IHP with various resting times. Then the cell adhesive forces were measured quantitatively utilizing a cell detachment test system and immunofluorescent staining was performed using fluorescent microscopy. In the results, immediately after mechanical stimuli (150 minutes after seeding) and one hour later (210 minutes after seeding), the average adhesive force of experimental group 5 (resting time: 15min) compared with that of control group at same culture time was increased significantly (p<0.05). The results indicated that IHP can contribute in improving cell adhesive force and some of time intervals were required for the expression of cell response.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.69-72
• /
• 2005

In this study, effects of IHPs with various resting times to cell adhesion were investigated through the measurements of cell adhesive force, number and area of focal contacts (stained vinculin spots), and projected cell area, perimeter and circularity. In addition correlation tests and curve estimations using the experimental results were performed fur the finding an essential factor for increment of cell adhesive force. Tn the results, immediately after mechanical stimuli (150 minutes after seeding) and one hour later (210 minutes after seeding), the average adhesive force of experimental group 5 (resting time: 15min) compared with that of control group at same culture time was increased significantly (p<0.05). Average projected area and perimeter of cells at Group 5 were increased significantly (p<0.05), while average circularity of cells at Group 5 incubated fur 210 minutes was decreased significantly (p<0.05). In the digital image analysis of focal contacts containing vinculins, area and numbers of focal contacts per cell at Group 5 were higher than those of the other groups. This study indicated that IHP with appropriate resting time could contribute in improving cell adhesive force, cell spreading, development of cytoskeleton and formation of focal contacts. And cell adhesive force was correlated to the morphological aspects of cell and development of focal contacts. Particularly, area of focal contacts was closely related to cell adhesive force.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.421-425
• /
• 2007

In the fabrication of dry adhesive structure, increasing contact-points or contact-area is the primary goal because the adhesive force grows in proportion to the contact-area. The simplest way to extend the contact surface is the fabrication by using soft materials. However, the column-array structure could confront the matting phenomenon which columns are stuck together. Therefore, we need a novel design to reduce the effective stiffness with adequate stiff materials like a gecko's setae. In this study, we propose a novel design for the dry adhesive structure. Moreover, we analyzed whether the adhesive structure conforms the rough surface sufficiently through finite element method adopted the non-bonding interaction as the body force. Also, we fabricated the novel structures via UV lithography and some techniques. In addition, we examined the adhesive force of the novel structures.

• 한국정밀공학회지
• /
• 제24권5호
• /
• pp.56-61
• /
• 2007

In the braking of railway rolling stock, the slip that is the relative velocity between train body and its wheel affects the adhesive force which is connected to the braking force. The coefficient of the adhesive force changes in accordance with the slip and the condition of a rail road. Namely, its value increases upon the maximum on a rail condition, and there it declines conversely while the magnitude of slip keeps rising on. First, this paper introduced a reference slip generator so that can utilize maximum adhesive forces with a disturbance observer for estimating unmeasurable current adhesive forces which is as an input of the generator. And, an adaptive sliding-mode control system has been synthesized for minimizing the error between reference and current slip. Finally the effectiveness of the proposed control system is evaluated by computer simulation.