• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.301.1-301.1
• /
• 2016

We report an ultraclean, cost-effective, and easily scalable method of transferring and patterning large-area graphene using pressure sensitive adhesive films (PSAFs) at room temperature. This simple transfer is enabled by the difference in wettability and adhesion energy of graphene with respect to PSAF and a target substrate. The PSAF transferred graphene is found to be free from residues, and shows excellent charge carrier mobility as high as ${\sim}17,700cm^2/V{\cdot}s$ with less doping compared to the graphene transferred by thermal release tape (TRT) or poly(methyl methacrylate) (PMMA) as well as good uniformity over large areas. In addition, the sheet resistance of graphene transferred by recycled PSAF does not change considerably up to 4 times, which would be advantageous for more cost-effective and environmentally friendly production of large-area graphene films for practical applications.

• Journal of the Microelectronics and Packaging Society
• /
• v.7 no.1
• /
• pp.35-40
• /
• 2000

Teflon-like fluorocarbon thin film was deposited on various substrates by vapor deposition using PFDA (perfluorodecanoic acid). The fluorocarbon films were characterized by static/dynamic contact angle analysis, VASE (Variable-angle Spectroscopic Ellipsometry) and AFM/LFM (Atomic/Lateral Force Microscopy). Based on Lewis Acid/Base theory, the surface energy ($S_{E}$) of the films was calculated by the static contact angle measurement. The work of adhesion (WA) between de-ionized water and substrates was calculated by using the static contact data. The fluorocarbon films showed very similar values of the surface energy and work of adhesion to Teflon. All films showed larger hysteresis than that of Teflon. The roughness and relative friction force of films were measured by AFM and LFM. Even though the small reduction of surface roughness was found on film on $SiO_2$surface, the large reduction of relative friction farce was observed on all films. Especially the relative friction force on TEOS was decreased a quarter after film deposition. LFM images showed the formation of "strand-like"spheres on films that might be the reason far the large contact angle hysteresis.

• Journal of the Korean Society for Heat Treatment
• /
• v.13 no.2
• /
• pp.91-97
• /
• 2000

The structure and mechanical properties of TiN and TiCN thin films deposited on STD61 steel substrates by the RF-sputtering methods has been studied by using XPS, XRD, micro-hardness tester, scratch tester, and wear-resistance tester. XPS results showed that the TiCN thin film formed with chemical bonding state. The TiN thin films grew with (111) orientation having the lowest strain energy by compressive stress, whereas the TiCN thin films grew with both (111) and (200) orientation, but (200) orientation having the lowest surface energy becomes dominant as carbon contents increase. The pre-etching treatment of substrate did not affect on the preferred orientation of thin films, but it played an important role in improving mechanical properties of thin films such as the hardness, adhesion and wear- resistance. Especially, the TiCN thin films showed the superior wear resistances due to high hardness and low friction coefficient compared with TiN thin films.

• Polymer(Korea)
• /
• v.26 no.6
• /
• pp.718-727
• /
• 2002

In this work, an Ar+ beam was irradiated on carbon fiber surfaces to improve the interfacial shear strength (IFSS) of the resulting composites using an ion assisted reaction (IAR) method h single fiber pull-out test was executed to investigate the basic characteristics of the single Carbon fiber/matrix interface. Based on Greszczuk's geometrical model, the debonding force for pull-out of the fiber from the resins was discussed with the applied ion beam energy as a result, it was known that an ion beam treatment produced the functional groups on fiber surface and etching lines along the fiber axis direction, resulting in increasing the adhesion forces between fibers and matrix, which caused the improvement of the IFSS in a composite system. And, it was also found that the maximum IFSS was shown at 0.8 keV ion beam energy in this system.

• Journal of Adhesion and Interface
• /
• v.22 no.3
• /
• pp.79-84
• /
• 2021

Graphene has been received a lot of attention as essential parts of future electronic and energy devices. Because of its extraordinary properties contributed from the atomic layer, the interface and surface engineering of graphene are promising approaches for realizing 2D materials-based high-performance devices. Herein, we summarize and introduce recent research trends of the synthesis of graphene through interface engineering for high-performance electronic and energy device applications, and then discuss the challenges and opportunities for achieving high-performance devices in next-generation electronics.

• Journal of Wind Energy
• /
• v.15 no.1
• /
• pp.82-90
• /
• 2024

Bio-fouling has positive aspects that are used as a fish resource, but there are also negative aspects such as corrosion of the surface of the support structure, aesthetics and work safety problems. A specimen was produced using a polyurea material with excellent anti-fouling and methodology, and contact angle, high water pressure, adhesion, and real sea area tests were performed. As a result of measuring the contact angle of the specimen with a 10 cm x 10 cm area of polyurea, There was found to be an average of 124.4 ° at nine points. No surface damage was found even above 5 Mpa when high water pressure was sprayed, and adhesive strength of 300LSE adhesives was confirmed between 22.84 and 23.04 Mpa with an adhesion test. During the 6-month real sea area test, it was confirmed that about 17.24 % of the polyurea film was less generated than the comparison group.

• Journal of Adhesion and Interface
• /
• v.25 no.2
• /
• pp.50-55
• /
• 2024

Hydrogen is attracting much attention as a renewable energy source with high energy density and environmental friendliness. Among various hydrogen production methods, water electrolysis stands out as a clean hydrogen production technique that could lead the future of hydrogen production, as it does not emit carbon, and many studies are currently underway to realize this technology. However, the high overpotential, which increases the cost of hydrogen production, acts as a stumbling block, making the development of electrocatalysts extremely important. This paper aims to summarize and introduce recent research trends in the development of electrocatalysts for hydrogen evolution reaction and oxygen evolution reaction through interfacial engineering, and to deeply discuss the challenges in implementing next-generation water electrolysis devices.

• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.38-43
• /
• 2001

The interfacial adhesive joining characteristics of the foams are very important for the structural integrity of sandwich structures. Peel strength is one of the best criteria for the interfacial characteristics of the sandwich structures and peel energy is most commonly used for the interfacial characteristics. The peel strength is the first peak force per unit width of bond line required to produce progressive separation by the wedge or other crack opening type action of two adherends where one or both undergo significant bending and the peel energy is the surface active energy per unit width of bond line. In this work, to investigate the strengthening effect of resin treatment on the interfacial surface of foam material, peel strength and peel energy of epoxy resin treated polyurethane foam core sandwich structures were obtained by the cleavage peel tests and compared with those of non surface treated polyurethane foam core sandwich structures.

• Journal of Electrochemical Science and Technology
• /
• v.6 no.2
• /
• pp.35-49
• /
• 2015

Advanced polymeric binders with unique functions such as improvements in the electronic conduction network, mechanical adhesion, and mechanical durability during cycling have recently gained an increasing amount of attention as a promising means of creating high-performance silicon (Si) anodes in lithium-ion batteries with high energy density levels. In this review, we describe the key challenges of Si anodes, particularly highlighting the recent progress in the area of polymeric binders for Si anodes in cells.

• Journal of Adhesion and Interface
• /
• v.9 no.2
• /
• pp.24-31
• /
• 2008

In this work, calcium hydroxide and magnesium carbonate as metal ionic crosslinking agents were used to introduce ionic crosslinking points to the ethylene vinylacetate (EVA) emulsions for the enhancement of water resistance and mechanical properties of emulsion films. The properties of EVA emulsion film were investigated in crosslinking density, thermal features, surface energy, and mechanical properties, such as tensile strength, elongation at break and tear strength. With the increasing content of metal ionic crosslinking agent, the crosslinking density of the EVA emulsion film increases, resulting into the improvement of water resistance. The surface energy and mechanical properties of the EVA emulsion film, however, showed somewhat different behaviors. The highest surface energy, tensile strength, and tear strength were observed when 0.4% for calcium hydroxide and 0.5% for magnesium carbonate was added respectively, because the EVA emulsion containing carboxylic acid forms strong carboxylate-metal bond of ionically-crosslinked system. Therefore, it can be concluded that metal ionic crosslinking agents, such as magnesium carbonate and calcium hydroxide are considered to improve water resistance and mechanical properties of the EVA emulsion.