• Korean Journal of Materials Research
• /
• v.18 no.8
• /
• pp.417-421
• /
• 2008

$Al_2O_3$ sol with long-term stability was prepared by mechanical milling. Thin films were evaluated and created for use as coating materials. The particle size of the manufactured sol was 98 nm when 2 wt% of nitric acid was added. This indicates that the viscosity of the sol is 12 cps and that it has long-term stability. The thickness of the thin films, which varied from 100 nm to 500 nm, could be managed by adjusting the draw rate and the amount of an organic additive. A thin film heated to $500^{\circ}C$ indicated a hydrophilic property against water and excellent permeability against a visible ray.

• Journal of the Korean Ceramic Society
• /
• v.55 no.1
• /
• pp.36-43
• /
• 2018

The physical and chemical analyses of mineral waste such as moisture content, water absorption, freezing-thawing resisting sexual, chemical composition and crystal structure were investigated. In the technological process of crushing, screening, molding, drying, preheating, sintering and cooling, many parameters were changed to eliminate the influence of freeze thaw stability and the ball billets were processed into slate ceramsites eventually. Adopting orthogonal experiment and range analysis, the optimal technology parameters were confirmed as preheating temperature of $300^{\circ}C$ for 25 minutes and sintering temperature of $1230^{\circ}C$ for 20 minutes. Slate wastes in Shangri-la could foam and expand without any additive. The ultra-light ceramsite could be directly used as building aggregate, since the analysis results of its leaching toxicity were eligible. Besides, effects of sintering temperature on physical property and crystal phase were also explored in this study.

• Corrosion Science and Technology
• /
• v.19 no.1
• /
• pp.23-30
• /
• 2020

Heat sinks are most widely used in thermal management systems; however, the heat dissipation efficiency is usually limited. Therefore, in order to increase heat dissipation efficiency of the heat sink, the heat-dissipating paint using 2D materials (hexagonal boron nitride (h-BN) and graphene) as thermally conductive additive was designed and evaluated in the present study. The heat dissipation performance of the paint was calculated from temperature difference between the paint-coated and -uncoated specimens mounted on the heat source. The highest heat dissipation performance was obtained when the ratio of h-BN to resin was 1/10 in the paint. In addition, further reduction in the temperature of the test specimen by 6.5 ℃ was achieved. The highest heat dissipation performance of the paint prepared using graphene was achieved at a 1/50 ratio of graphene to the resin, and a 6.5 ℃ reduction was attained. In addition, graphene exhibited enhanced corrosion resistance property of heat-dissipating paint by inhibiting the growth of the paint blisters.

• Clean Technology
• /
• v.22 no.4
• /
• pp.299-307
• /
• 2016

These days, coal is one of the most important energy resources used for transportation, industry, and electricity. There are two types of coal: high-rank and low-rank. Low-rank coal has a low calorific value and contains large amounts of useless moisture. The quality of low-rank coal can be increased by simple drying technology and it needs to be stabilized by hydrocarbons (e.g. palm acid oil, PAO) to prevent spontaneous combustion and moisture re-adsorption. Spontaneous combustion becomes a major problem during coal mining, storage, and transportation. It can involve the loss of life, property, and economic value; reduce the quality of the coal; and increase greenhouse gas emissions. Besides spontaneous combustion, moisture re-adsorption also leads to a decrease in quality of the coal due to its lower heating value. In this work, PAO was used for additive to stabilize the upgraded coal. The objectives of the experiments were to determine the stabilization characteristic of coal by analyzing the behavior of upgraded coal by drying and PAO addition regarding crossing-point temperature of coal, the moisture behavior of briquette coal, and thermal decomposition behavior of coal.

• Polymer(Korea)
• /
• v.38 no.6
• /
• pp.726-734
• /
• 2014

Three different types of additives, thiokol, epoxidized natural rubber (ENR) and epoxidized linseed oil (ELO), were dispersed in an epoxy matrix before being used in glass fiber (GF) composites, and their effects on the mechanical and dielectric properties of epoxy resin and glass fiber reinforced epoxy composites (GF/EP) were examined. The addition of each of 7 phr ENR, 9 phr ELO and 5 phr thiokol into the epoxy resin increased the fracture toughness significantly by 56.9, 43.1, and 80.0%, respectively, compared to the unmodified resin. The mode I interlaminar fracture toughness of the GF/EP at propagation was also improved by 26.9, 18.3 and 32.7% when each of 7 phr ENR, 9 phr ELO, and 5 phr thiokol, respectively, was dispersed in the epoxy matrix. Scanning electron microscopy showed that the additives reduced crack growth in the GF/EP, whereas their dielectric measurements showed that all these additives had no additional effect on the real permittivity and loss factor of the GF/EP.

• Korean Journal of Materials Research
• /
• v.13 no.8
• /
• pp.531-536
• /
• 2003

The electromagnetic properties and microstructures of the ferrites based on ($Ni_{0.2}$ $Cu_{0.2}$ $Zn_{0.6}$)$_{1.085}$($Fe_2$$O_3$)$_{0.915}$ were investigated by changing the amount of additive SnO$_2$and CaO and the sintering temperatures. Addition of $SnO_2$caused pores in the specimen. There was no variation of grain size by changing the amount of additives. Total loss was reduced when ($Ni_{0.2} $Cu_{0.2}$ $Zn_{ 0.6}$)$_{1.085}$ ($Fe_2$$O_3$)$_{0.915}$ composition was sintered at $1150^{\circ}C$ rather than $1300^{\circ}C$. Addition of CaO was useful to reduce the total loss because it increased the sintering density. The lowest total loss was obtained when 0.06 wt% $SnO_2$and 0.4 wt% CaO were added at the same time.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.4
• /
• pp.356-360
• /
• 2002

The piezoelectric properties of $0.05Pb(Al_{0.5}Nb_{0.5})O_3-0.95Pb(Zr_{0.52}Ti_{0.48})O_3+0.7wt%Nb_2O_5+o.5wt%MnO_2$ ceramics with the additive of BaCO$_3$were investigated. As the addition of BaCO$_3$increased from 0 to 0.4 wt%, the dielectric constant ($\epsilon^T _{33}$), piezoelectric constant ($d_33$), electromechanical coupling factor ($k_p$), and mechanical quality factor ($Q_m$) increased, while the dielectric loss ($tan\delta$) decreased. The highest piezoelectric and dielectric properties were observed at $1200^{\circ}C$ of the sintered temperature with 0.4 wt% of $BaCO_3$, and the properties of $d_33$, $k_p$, and $Q_m$ were 339 pC/N, 60% and 1754, respectively.

• Journal of the Korean Ceramic Society
• /
• v.40 no.3
• /
• pp.229-233
• /
• 2003

By using an oxynitride glass as a sintering additive, the effects of BN content on microstructure and mechanical properties of the hot-pressed and subsequently annealed SiC-BN composites were investigated. The microstructures developed were analyzed by image analysis. The morphology of SiC grains was strongly dependent on BN content in the starting composition. The aspect ratio of SiC decreases with increasing BN content and the average diameter of SiC shows a maximum at 5 wt% BN and decreases with increasing BN content in the starting powder. The fracture toughness increased with increasing BN content while the strength decreased with increasing BN content. The strength and fracture toughness of SiC or SiC-TiC composites were strongly dependent on the morphology of SiC grains, but the strength and fracture toughness of SiC-BN composites were strongly dependent on BN content rather than morphology of SiC grains. These results suggest that fracture toughness of SiC ceramics can be tailored by manipulating BN content in the starting composition. Typical fracture toughness and strength of SiC-10 wt% BN composites were 8 MPa$.$m$\^$1/2/ and 445 MPa, respectively.

• Journal of the Korean Ceramic Society
• /
• v.21 no.2
• /
• pp.105-112
• /
• 1984

The Effect of Dditives $ZrO_2$ and $TiO_2$ on the enstatite body the composition of which was MgO.$SiO_2$ has been closely investigated on the physical properties and microstructure. $ZrO_2$ and $TiO_2$ as additives were added by weight 5, 10, 15, 20, 25% and 1, 2, 2.5, 5, 10, 20% respectively to the mixture (MgO : SiO2=1:1) and fired at the temperature ranging from 130$0^{\circ}C$ to 145$0^{\circ}C$ and 1275$^{\circ}C$ to 1375$^{\circ}C$. Increasing the add ition or $ZrO_2$ to 20% the physical property became better. In case of $TiO_2$ the sample containing 20% $TiO_2$ had a best effect on the enstastite body. The optimum firing range proved to 14$25^{\circ}C$ for $ZrO_2$ and 1325~135$0^{\circ}C$ for $TiO_2$. The effect of $ZrO_2$ and $TiO_2$ addition on the thermal expansion was observed not ot be remarkable.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.4
• /
• pp.288-292
• /
• 1998

In this paper, we fabricated $SnO_2$ composite ceramics doped with 0~20mol% $SnO_2$ of bulk type to investigate the CO and $H_2$ gas sensitivity in various composition, temperature, and concentration of CO and $H_2$ gas. At the temperature range from $100^{\circ}C\sim425^{\circ}C$, the measured 1000ppm and 250ppm CO gas sensitivities of $SiO_2-SnO_2$composite ceramics were about 1.0~7.6 and 1.0~5.6, respectively. These values were about 1.0~1.5 times larger than pure $SnO_2$. The maximum 1000ppm CO gas sensitivity of $SiO_2-SnO_2$composites were measured around $325^{\circ}C$. At the temperature range from $270^{\circ}C\sim380^{\circ}C$, the 1000ppm and 500ppm $H_2$gas sensitivities of $SiO_2-SnO_2$ composites were about 2.9~21.2 and 2.1~11.3, respectively. Also the maximum 1000, 500 ppm $H_2$ gas sensitivities of samples were measured around.