• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2003년도 학술.기술논문발표회
• /
• pp.81-87
• /
• 2003

The purpose of this study is the development of a recycling process to recover the hydrated ability of cement hydrate which accounts for a large proportion of cementitious powder by concrete waste in order to recycle cementitious powder by concrete waste as recycle cement. Therefore, after having theoretical consideration based on the properties of high-heated concrete, we consider the properties of hydration of cementitious powder in hardened mortar under various temperature conditions. As a result of experiment, it is revealed that an effective development of recycling cement is possible since the cementitious powder by concrete waste recovers a hydraulic property during burning at $600^{\circ}C$ or $700^{\circ}C$. And it is shown that the fluidity of mortar decreases rapidly as the burning temperature of recycle cement increases. however, the improved effect of fluidity is predominant if adding the additive such as fly-ash or blast furnace slag.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2016년도 추계학술대회 논문집
• /
• pp.166.1-166.1
• /
• 2016

철(Fe)을 주체로 하는 경질피막의 하나로 전극에 의한 W를 함유한 피막의 제조가 알려져 있다. W는 단독으로 수용액으로부터 석출시킬 수 없고 Fe, Ni 등의 철(Fe)족 금속이온을 함유한 수용액에서 유도 공석한 합금피막을 얻을 수 있다. 합금도금 피막은 비정질 구조를 형성하기 쉽고 내산성, 내마모성이 뛰어나고 고융점 금속(W)을 함유한 피막이기 때문에 내열재료로 이용할 수 있다. 본고에서는 Fe-Ni-W 합금도금의 피막 특성에 미치는 아스코르빈산염 농도의 영향에 주목하여 얻은 피막의 조성, 결정구조, 경도, 내마모성과 열처리 영향을 기술하였다.

• ETRI Journal
• /
• 제32권3호
• /
• pp.490-492
• /
• 2010

This letter proposes a robust feature extraction method using a spatially normalized mean for temporal ordinal measurement. Before computing a rank matrix from the mean values of non-overlapped blocks, each block mean is normalized so that it obeys the invariance property against linear additive and subtractive noise effects and is insensitive against multiplied and divided noise effects. Then, the temporal ordinal measures of spatially normalized mean values are computed for the feature matching. The performance of the proposed method showed about 95% accuracy in both precision and recall rates on various distortion environments, which represents the 2.7% higher performance on average compared to the temporal ordinal measurement.

• 한국세라믹학회지
• /
• 제28권12호
• /
• pp.943-952
• /
• 1991

Lead zirconate titanate(PZT) powders and thin films were prepared from an alkoxide-based solution by sol-gel method. Gelation of synthesized complex solutions, pyrolysis and crystallization behaviors of the dried powder were studied in accordance with a water content and a catalyst. PZT thin films were formed by spin-casting method on silicon and platinum substrates, and characterized. Ester produced from the reactions was completely removed when drying of the gel was finished. Pyrolysis property of the dried PZT gels were changed in order water content, class of catalyst, and quantity of catalyst. Crystalline Pb phase was transiently formed near 250$^{\circ}C$. Basic catalyst is good additive for a formation of perovskite phase in the films, and acidic catalyst for a densified film structure. By the analysis of RBS, Pb element in the PZT films were diffused into silicon substrate, and the pores, may be produced due to local densification around some grains in the films, make an origin of fault in microstructure when holding time goes to be longer at 700$^{\circ}C$.

• Elastomers and Composites
• /
• 제50권4호
• /
• pp.304-313
• /
• 2015

In this study, the anionic emulsified asphalt was prepared by dispersing asphalt particles evenly into water with combination of anionic and nonionic surfactants. Effects of NaOH and $CaCl_2$ on the phase stability of the emulsified asphalt were also investigated through zeta potential value and rheology behavior; the emulsified asphalt added with NaOH and $CaCl_2$ showed higher zeta potential value than that the asphalt with addition of only anionic and nonionic surfactants. In addition, with regard to shear thinning behaviors, it was found that pH of the emulsified anionic asphalt and $Ca^{2+}$, counter ion, affected the phase stability. SBR (styrene-butadiene-rubber) latex, EPD (water dispersed Epoxy), PU (polyurethane) and RI-10S, SBS (styrene-butadiene-styrene)-based property improvement additive, were used and studied to enhance the adhesion properties with the aggregates. RI-10S, however, was found to be only compatible with the anionic emulsified asphalt; the coating rate, adhesion and compression strength were increased with the RI-10S content.

• 대한화학회지
• /
• 제57권5호
• /
• pp.591-598
• /
• 2013

A series of chiral prolinamide compounds with pyridine-2, 6-dicarboxylic acid moieties derived from L-proline have been designed and synthesized, their catalytic properties for direct asymmetric aldol reactions were also studied in this article. These catalysts gave the aldol product in high yield (87%) and high enantioselectivity, up to 85%, of the anti-structure at room temperature but gave disappointing results at a lower temperature or when additive was added. Conditions, including solvents, temperature and additives were screened for the reactions. Moreover, the influence of presence of water on yield and stereoselectivity was also discussed.

• KIEAE Journal
• /
• 제7권5호
• /
• pp.121-126
• /
• 2007

This is the experimental study on the functional property of the light-weight concrete according to the mineral composite. According to the increase of the functional mineral, Autoclaved light-weight concrete (ALC) have a effect of high far infrared ray, deodorization, anion and change of chromaticity on D65 of light source. Compressive strength and change of specific gravity by foaming of Mixed Slurry in accordance with additive rates and Water. It chracterizes surface by SEM, chemical component and crystallization by XRD, XRF. the results of this experiment studied influences of ALC by functional minerals.

• 한국통신학회논문지
• /
• 제22권12호
• /
• pp.2772-2782
• /
• 1997

본 논문에서는 백색 잡음으로 훼손된 영상을 복원하기 위하여 웨이브렛 변환 영역에서의 Wiener 필터링 기법을 제안하였다. 제안된 방법에서는 웨이브렛 변환 신호의 특성과 각 부대역 내에서의 국부 통계를 이용한다. 각부대역에서 국부 통계를 구할때는 스케일에 따라 필터 창의 크기를 달리하였다. 이때 웨이브렛 부대역에서는 필터 창내의 통계적 특성이 유사한 화소들만으로 국부 통계를 구하였다. 실험결과, 제안된 방법은 고정된 필터 창의 크기를 갖는 Lee 필터에 비하여 성능이 우수함을 알 수 있었다.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.195-196
• /
• 2006

In recent years, demands for sintered ferrous material with higher strength are increasing. To satisfy these demands, studies and commercial use of the die wall lubrication method, the warm compaction method and the combination of both methods are widely carried out to achieve high density. The die wall lubrication warm compaction method makes it possible to achieve high density by reducing internal lubricant through die wall lubrication, although the method involves several issues such as prolonged cycle time due to lubricant spraying and difficulty in spraying lubricant in the case of compacting with complicated geometry. Meanwhile, the conventional warm compaction method requiring no die wall lubricant application cannot achieve such a high density as in the case of die wall lubrication warm compaction due to higher volume of internal lubricant. However, this report discloses our study result in which the possibility of improving density is exhibited by using a lubricant type with superior dynamic ejection property that can reduce volume of lubricant additive.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.521-522
• /
• 2006

Laser additive direct deposition of metals is a new rapid manufacturing technology, which combines with computer aided design, laser cladding and rapid prototyping. The advanced technology can build fully-dense metal components directly from CAD files with neither mould nor tool. Based on the theory of this technology, a promising rapid manufacturing system called "Laser Metal Deposition Shaping (LMDS)" is being developed significantly. The microstructure and mechanical properties of the LMDS-formed samples are tested and analyzed synthetically. As a result, significant processing flexibility with the LMDS system over conventional processing capabilities is recognized, with potentially lower production cost, higher quality components, and shorter lead time.