• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 추계학술대회 논문집
• /
• pp.546-552
• /
• 2012

This paper is a study on squeal noise simulation under the consideration of temperature and pressure dependent material properties of friction material. For this, data of pressure and temperature dependent material properties of lining is achieved by using lining data base and exponential curve fit. Complex eigenvalue analysis is performed for predicting squeal noise frequency and instability and chassis dynamo test is performed for achieving squeal noise frequency, sound pressure level, occurrence temperature & pressure. Initial multi models are composed for considering complex interface conditions such as pad ear-clip, piston-housing and guide pin-torque member. The simulation result of base models is compared with the test result. Squeal noise simulation under the consideration of temperature and pressure dependent material properties of friction material is performed and analyzed using multi models. And additional condition is disc material property variation. Entire simulation conditions are combined and analyzed. Finally, this paper proposes direction of the warm squeal noise model.

• 한국자동차공학회논문집
• /
• 제6권6호
• /
• pp.210-217
• /
• 1998

This paper describes the method for detection of the misfired cylinder using the pressure fluctuations occurred in the exhaust system on an MPI gasoline engine. If misfire is occurred in the cylinder of the gasoline engine, the power of engine gets lost, the fuel consumption and the exhaust emission are increased and the vibration is caused by unsteady torque. Therefore early detection and correction of misfire play a very important role in the proper performance and the exhaust emission. This paper suggests method of misfire detection which affect engine performance. The method is a comparison of average pressure index during the displacement period. Experimental results showed that the method using the pressure fluctuations in the exhaust system is proven to be effective in the detection of misfire on gasoline engine regardless loads and revolutions of the engine. In addition, this method, using the pressure fluctuations in exhaust system is easier than other methods and is not a need of additional reconstruction of engine.

• 천문학회보
• /
• 제44권1호
• /
• pp.77.1-77.1
• /
• 2019

It has been proposed by Gunn & Gott (1972) that galaxies may lose their interstellar gas by ram pressure due to the dense intra-cluster medium while falling to the cluster potential. The observational evidence for this process, which is known as ram pressure stripping, is increasing, and it is believed to be one of the key environmental effects that can dramatically change the star formation activity of galaxies and hence their evolution. Intriguingly however, some cases with clear signs of ram pressure stripping are found in the environment which betrays our expectations (e.g. large clustercentric distances), and our understandings to the detailed working principle behind ram pressure stripping seem to be still lacking. As one of the ways to gain more theoretical insights into the conditions for ram pressure stripping process, we have been comparing the gas truncation radius which is predicted based on the simple Gunn & Gott's prescription with what is actually observed in a sample of carefully selected Virgo galaxies. In this work, we present the results of our comparisons between the theoretically predicted truncation radius and the observationally measured truncation radius for individual galaxies in the sample and discuss which additional conditions are needed in order to fully understand the observations.

• Journal of Korean Neurosurgical Society
• /
• 제30권3호
• /
• pp.295-306
• /
• 2001

Objectives : The management of massive brain swelling remains an unsolved problem in neurosurgical field. Despite newly developed medical and pharmacological therapy, the mortality and morbidity due to massive brain swelling remains high. According to many recent reports, surgical decompression with dura expansion is superior to medical management in patients with massive brain swelling. We performed surgical treatment on the first line of treatment, and followed medical management in case with refractory increased intracranial pressure(ICP). To show the quantitative effect of decompressive surgery on the intracranial pressure, we performed ventricular puncture and checked the ventricular ICP continuously during the decompressive surgery and postoperative period. Materials and Methods : Fifty-one patients with massive brain swelling, undergoing bilateral decompressive craniectomy with dura expansion, were studied in this study. In all patients, ventricular puncture was performed at Kocher's point on the opposite side of massive brain swelling. The ventricular pressure was monitored continuously, during the bilateral decompression procedures and postoperative period. Results : The initial ventricular ICP were varied from 13mmHg to 112mmHg. Immediately after the bilateral craniectomy, mean ventricular ICP decreased to $53.1{\pm}15.8%$ of the initial ICP(ranges from 5mmHg to 87mmHg). Dura opening decreased mean ICP by additional 36.7% and made the ventricular pressure $16.4{\pm}10.5%$ of the initial pressure (ranges from 0mmHg to 28mmHg). Postoperatively, ventricular pressure was lowered to $20.2{\pm}22.6%$(ranged from 0mmHg to 62.3mmHg) of the initial ICP. The ventricular ICP value during the first 24 hours after decompressive surgery was found to be an important prognostic factor. If ICP was over 35mmHg, the mortality was 100% instead of additional medical(barbiturate coma therapy and hypothermia) treatments. Conclusion : Bilateral decompression with dura expansion is considered an effective therapeutic modality in ICP control. To obtain favorable clinical outcome in patients with massive brain swelling, early decision making on surgical management and proper patient selection are mandatory.

• 한국지반공학회논문집
• /
• 제22권6호
• /
• pp.27-40
• /
• 2006

개착식 터널라이닝의 파괴 원인은 물리적 요인과 공학적 요인으로 나눌 수 있다. 물리적 요인으로서는 재료특성, 보강재 부식 등이 있으며, 공학적 요인은 수압과 교통진동 등이 있다. 본 연구에서는 공학적 요인 중 부가하중 즉, 공사를 완료한 뒤에 라이닝의 변형 및 파괴를 유발하는 증가 토압에 초점이 맞추어져 있다. 증가 토압은 되메움토의 다짐 불량, 자중 및 강우에 의한 침하, 교통하중에 의한 진동 등이 원인이 되어 발생한다. 본 연구는 모래 지반에 $1.0D{\sim}1.50D$ 깊이에 개착식으로 시공하는 원형의 강성 터널에 작용하는 토압에 관한 것으로 진동다짐의 영향을 모형 실험에서 충분히 반영하기 위하여 100Hz의 진동주파수를 사용하였다. 본 연구에서는 개착식 터널 라이닝에 작용하는 토압과 주변 지반의 변형 양상을 파악하고 기존 토압 계산공식을 검토하기 위해 실내 터널모형실험을 실시하였으며, 개착식 터널 라이닝에 작용하는 측정 토압과 토압공식에 의해 산출한 토압을 비교 분석하여 기존 공식에 대한 안전율을 제시하였다.

• 대한조선학회논문집
• /
• 제43권5호
• /
• pp.586-596
• /
• 2006

A 3-dimensional FDLB model with additional internal degree of freedom is applied for diatomic gases such as air, in which an additional distribution function is introduced. Direct simulations of aero-acoustic by using the applied model and scheme are presented. Speed of sound is correctly recovered. As typical examples, the Aeolian tone emitted by a circular column is successfully simulated even very low Mach number flow. Acoustic pressure fluctuations with the same frequency of the Karman vortex street compared with the pressure fluctuation around a circular column is captured. Full three-dimensional acoustic wave past a compact block like pentagon, furthermore, is also emitted in y direction as dipole like sound.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2001년도 춘계학술발표대회 논문집
• /
• pp.172-175
• /
• 2001

The co-cured Joining method, which is regarded as an adhesively bonded Joining method, is an efficient joining technique because both curing and bonding processes for the composite structures can be achieved simultaneously. It requires neither surface treatment onto the composite adherend nor an additional adhesive joining process because the excess resin, which is extracted from composite materials during consolidation, accomplishes the co-cured Joining process. Since the adhesive of the co-cured joint is the same material as the resin of the composite adherend, the analysis and design of the co-cured joint for composite structures are simpler than those of an adhesively bonded joint, which uses an additional adhesive. In this paper, effects of the manufacturing parameters, namely surface roughness, stacking sequence of the composite adherend, and manufacturing pressure in the autoclave during curing process, on the tensile load bearing capacity of the co-cured single lap joint will be experimentally investigated.

• 한국수소및신에너지학회논문집
• /
• 제27권5호
• /
• pp.485-493
• /
• 2016

Recently submarine and unmanned underwater vehicle (UUV) are equipped with a fuel cell system as an air independent propulsion system. Methanol fuel processor can efficiently supply the hydrogen to the fuel cell system to improve the ability to dive. This study investigated the optimal conditions of the methanol fuel processor that may be used in the closed environment. For this purpose, the numerical model based on Gibbs minimization equation was established for steam reformer and three exhaust gas burners. After simulating the characteristics of steam reformer according to the steam-to-carbon ratio (SCR) and the pressure change, the SCR condition was able to narrow down to 1.1 to 1.5. Considering water consumption and the amount of heat recovered from three burners, the optimum condition of the SCR can be determined to be 1.5. Nevertheless, the additional heat supply is required to satisfy the heat balance of the methanol fuel processor in the SCR=1.5. In other to obtain additional amount of heat, the combustion of methanol is better than the increased of SCR in terms of system design.

• 한국자동차공학회논문집
• /
• 제5권2호
• /
• pp.50-59
• /
• 1997

When a front head of train enters a tunnel at a high speed, compression wave is generated at tunnel entrance due to the confinement effect and propagated along the tunnel with sound of speed. The propagated compression wave is reflected at tunnel exit due to abrupt pressure change at passage. The reflected wave is expansion pressure wave. And when the rear head of train goes through the tunnel entrance, another expansion pressure wave is generated and propagated along the tunnel. The pressure drop occurs seriously around train when the two expansion pressure waves come cross on train in the tunnel. In order to reduce the pressure drop, the compression wave front must be controlled because the intensity and magnitude of pressure drop is nearly proportional to that of compression wave at tunnel entrance. This study relates to reduction of the pressure wave gradient with respect to tunnel entrance shape change with various kind of angle and rounding. The results show characteristics of wave propagation in tunnel, usefulness of characteristic curve to estimate proper time domain size in numerical study and measuring time in actual experiment. Also rounding is contributed to improve pressure wave front even if its radius is very small at tunnel entrance. In order to improve of pressure wave front at tunnel entrance, proper angle is prefered to rounding with big radius and an angle of around 14$^{\circ}$ is recommended according to this simulations, And it is expected to reduce additional pressure drop in tunnel when the location and the size of the internal space for attendant equipment are considered in advance.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2004년도 학술대회지
• /
• pp.201-208
• /
• 2004

In this study a general Galerkin FE lubrication analysis method was utilized to analyze the complex lubrication performance of a spiral groove seal having an additional inner circular groove, which was designed for a chemical process mixer operating at a low speed of the maximum 500 rpm. Equilibrium seal clearance analyses under varying outer pressure revealed that the seal maintains a certain levitation seal clearance under the outer pressure of more than about 1.5 bar, regardless of a rotating speed. Also, under the normal outer pressure of 11 bar, the axial stiffness of the seal was predicted to have a high value of more than 7.0e+07 N/m, regardless of a rotating speed and thereby, the seal is expected to maintain a stable thickness of lubrication film under a certain external excitation acting.