• Progress in Superconductivity and Cryogenics
• /
• v.12 no.1
• /
• pp.1-5
• /
• 2010

Silver stabilizing layer of coated conductor has been prepared by dip coating method using organic silver complexes containing 10 wt% silver as a starting material. Coated silver complex layer was dried in situ with hot air and converted to crystalline silver by post heat treatment in flowing oxygen atmosphere. A dense continuous silver layer with good surface coverage and proper thickness of 230 nm is obtained by multiple dip coatings and heat treatments. The film heat treated at $500^{\circ}C$ showed good mechanical adhesion and crystallographic property. The interface resistivity between superconducting YBCO layer and silver layer prepared by dip coating was measured as $0.67\;{\times}\;10^{-13}\;{\Omega}m^2$. Additional protecting copper layer with the thickness of $20\;{\mu}m$ was successfully deposited by electroplating. The critical current measured with the specimen prepared by dip coating and sputtering on same quality YBCO layer showed similar value of ~140 A and proved its ability to replace sputtering method for industrial production of coated conductor.

• Journal of the Korean Society for Heat Treatment
• /
• v.32 no.5
• /
• pp.201-211
• /
• 2019

Low carbon steel (S20C steel) and SPCC steel sheet have been austenitic nitrided at $700^{\circ}C$ in a closed pit type furnace by changing the flow rate of ammonia gas and heat treating time. When the flow rate of ammonia gas was low, the concentration of residual ammonia appeared low and the hardness value of transformed surface layer was high. The depth of the surface layer, however, was shallow. With increasing the concentration of residual ammonia by raising up the ammonia gas flow, both the depth of the surface layer and the pore depth increased, while the maximum hardness of the surface layer decreased. By introducing a large amount of ammonia gas in a short time, a deep surface layer with minimal pores on the outermost surface was obtained. In this experiment, while maintaining 10~12% of residual ammonia, the flow rate of inlet ammonia gas, 7 liter/min, was introduced at $700^{\circ}C$ for 1 hour. In this condition, the thickness of the surface layer without pores appeared about $60{\mu}m$ in S20C steel and $30{\mu}m$ in SPCC steel plate. Injecting additional methane gas (carburizing gas) to this condition played a deteriorating effect due to promoting the formation of vertical pores in the surface layer. For $1^{st}$ transformed surface layer for S20C steel, maintaining 10~12% residual ammonia condition via austenitic nitriding process resulted in ${\varepsilon}$ phase with relatively high nitrogen concentration (just below 4.23 wt.%N) among the mixed phases of ${\varepsilon}+{\gamma}$. The ${\varepsilon}$ phase was formed a specific orientation perpendicular to the surface. For $2^{nd}$ transformed layer for S20C steel, ${\gamma}$ phase was rather dominant (just above 2.63 wt.%N). For SPCC steel sheet, there appeared three phases, ${\gamma}$, ${\alpha}(M)$ and weak ${\varepsilon}$ phase. The nitrogen concentration would be approximately 2.6 wt.% in these phases condition.

• Journal of the Korean Wood Science and Technology
• /
• v.46 no.5
• /
• pp.497-510
• /
• 2018

In this study, the decay resistance of larch wood, which was heat treated by superheated steam, was evaluated by the field decay test. During the field decay test of 12 months, non-treated wood has been severely damaged by termite, however, no visible damage has occurred in the preservative-treated wood and superheated steam heat-treated wood. Results of field decay test showed approximately 5% mass loss of the non-treated wood and the preservative-treated wood, and approximately 1% mass loss of the superheated steam heat-treated wood. After the field decay test for 12 months, the residual amount of preservatives remaining in the preservative-treated wood was lower than that before the field decay test. It was considered that the preservative was partially eluted during the field decay test, and the mass loss of the preservative-treated wood was thought to be similar to that of the non-treated wood. Through this study and additional long-term monitoring test, superheated steam heat treatment can be considered to be an environmental-friendly method to enhance the decay resistance of wood against rot fungi and/or insect without chemical treatment such as preservative injection.

• Transactions of Materials Processing
• /
• v.23 no.7
• /
• pp.439-445
• /
• 2014

Changes in the accuracy of the geometrical shape after a surface treatment are often very large due to the variation of the deformation mechanisms such as edge draw-in and the variation in springback caused by the reduction in the coefficient of friction between the tool and the blank. In the present study, the resulting shape accuracy due to the changes in deformation is quantitatively examined in order to predict the variation and to remove any undesirable additional tool compensation for the center pillar member made from steel with a UTS of 980MPa. The study examines important process parameters that are closely related with the edge draw-in such as the blank holding force, the contact status between the tool and the blank and the friction coefficient. The proposed method is applied within the finite element analysis of the stamping process for tools after a surface treatment and the amount of edge draw-in and flush values are compared between the analysis and experiments. The results demonstrate that the proposed quantification and finite element scheme are applicable to complicated tool compensation procedures and compensation can be designed effectively.

• Journal of Physiology & Pathology in Korean Medicine
• /
• v.27 no.5
• /
• pp.553-562
• /
• 2013

This study was performed to develop cold-heat and deficiency-excess pattern identification for dementia, as well as for standard Korean medicine diagnosis and treatment. Five experts comprised of 4 neuropsychiatrists of Korean medicine and 1 statistician to develop cold-heat and deficiency-excess pattern identification for dementia. We searched studies about pattern identification and selected 507 articles using Oasis search terms provided by the KIOM. As a result, 10 pattern identification research study were recruited. Moreover, we analyzed neuropsychological assessments for dementia that evaluate Behavioral and Psychological Symptoms of Dementia (BPSD) and cognitive function using experts conferences and we selected neuropsychological instruments using pattern identification. Six cold patterns, six heat patterns, ten deficiency patterns, and four excess patterns were identified according to the cold-heat and deficiency-excess pattern identification of dementia. We selected the Caregiver-Administered Neuropsychiatric Inventory and the Korean Mini-Mental State Examination as neuropsychological assessments of dementia, which examine behavioral symptoms and cognitive function, suspectively. We formed positive and negative correlation between Korean medicine pattern identification and neuropsychological assessments for dementia. We developed and suggested a forecast module of pattern identification for dementia. But, it is necessary to perform additional clinical trials to verify its validity and accuracy.

• Journal of the Mineralogical Society of Korea
• /
• v.22 no.4
• /
• pp.395-405
• /
• 2009

The maturity of amber matrix and inclusion was studied to explore the effect of heat treatment on the formation of the sun spangle in the transparent Baltic amber from Gdansk, Poland. Optical microscope revealed two types of inclusions in the original amber samples. The inclusions in the amber which had sun spangle were dramatically expanded by the heat treatment, comparing to those without sun spangle which contains fissure and shows different refractive index. The amber sample which didn't show sun spangle after the heat treatment showed a strong carbon related peak in TOF-SIMS spectra and weak oxygen related peak. it means that the maturity of this amber sample is comparatively higher than the one with spangle. The two amber samples show similar IR spectra before the heat treatment. However, the amber which had sun spangle exhibited an additional 1019 $cm^{-1}$ absorption peak and a more intense 887 $cm^{-1}$ peak. The different chemical compositions between the two types of amber is believed to be due to the different absorption spectra between 1000~600 $cm^{-1}$. According to the study of DSC analysis, the two samples show different DSC profiles. Although they have the same geological origin, their geological ages are different and have different chemical compositions. Thus, they exhibited different behavior after the heat treatment. The formation of sun spangle seemed to depend on the difference in the heat expansion rate of amber matrix with different maturity and chemical compositions.

• Asian-Australasian Journal of Animal Sciences
• /
• v.18 no.4
• /
• pp.545-551
• /
• 2005

A feeding trial was conducted to determine whether dietary vitamin C (200 mg/kg) and vitamin E (250 mg/kg) prevent any drops in egg shell quality under heat stress in broiler breeder hens. One hundred and sixty molted Ross broiler breeders were housed randomly in an individual cage at 83 weeks of age. Four dietary treatments with forty hens and four replications per treatment were control (no additional vitamins), vitamin C-, or vitamin E-supplemented and combined supplementation of the two vitamins. After a tenday-adaptation period at 25$^{\circ}C$, the ambient temperature was kept at 32$^{\circ}C$ for a three-week-testing period. Egg production dropped dramatically over week but it did not show a significant change among treatments (p<0.05). However, egg quality parameters such as egg weight, specific gravity, shell thickness, SWUSA, puncture force and shell breaking strength from the birds fed the diet with the combined vitamins C and E were significantly improved over those of the control group during the heat stress period (p<0.05). The hens fed the vitamin C diet improved tibia breaking strength (37.16 kg), statistically higher than the birds fed the control and the vitamin E diets (p<0.05). The hens fed the control diet showed higher serum corticosterone levels, a mean of 5.97 ng/ml, than those of the other treatments (p<0.05). The heat stress resulted in elevated heterophils and decreased lymphocytes in serum, increasing the H/L ratios for all the treatments. However, the increases in H/L ratios were alleviated by feeding the diets containing vitamin C alone or together with vitamin E, although there were no significant differences in the ratio between the two groups (p<0.05). In conclusion, vitamins C (200 mg/kg) and/or E (250 mg/kg) supplemented to the diets for broiler breeder hens could prevent drops in egg shell quality and tibia bone strength under highly stressful environmental temperatures.

• Journal of the Korean Society for Heat Treatment
• /
• v.6 no.3
• /
• pp.166-177
• /
• 1993

Bending fatigue strength tests were made for VC coated die steels which were coated by immersing in a molten borax bath and for hardened die steels which were quenched and tempered, in order to clarify the effect of VC coating at $1000^{\circ}C$ and $1025^{\circ}C$. The material used in this investigation was a representative cold and hot die steels STD11, STD61. The results obtained are as follows. 1) The endurance limit of VC coated die steels was a little lower than that of hardened die steels. It is considered to be mainly due to the decfl.lase of hardness in the substrates. Accordingly, the endurance limit reo covered almost to the level of hardened die steels by an additional diffusion treatment. 2) The initiation point of fatigue fracture of VC coated die steels in reversed bening was on the substrate just under the VC layer. Hence, the endurance limit is corrected to the hardness of this part. 3) But, there is a considerable scatter in this relationship and the endurance limit of VC coated die steels was a little lower than that of hardened die steels with equal hardness. These results suggest that the fatigue strength of VC coated die steels is determined not only by the hardness but also by other factors. For example. the residual stress in the substrate just under VC coating layer is one of the factors besides hardness which is mainly related to the retained austenite(${\gamma}_R$).

• Journal of Welding and Joining
• /
• v.33 no.5
• /
• pp.1-8
• /
• 2015

Aluminium and its alloys are widely used in brazing various components in automotive industries due to their properties like lightweight, excellent ductility, malleability and formability, high oxidation and corrosion resistance, and high electrical and thermal conductivity. However, high machinability and strength of aluminium alloys are a serious concern during casting operations. The generation of porosity caused by dissolved gases and modifiers affects seriously the strength and quality of cast product. Brazing of Al and its alloys requires careful monitoring of temperature since theses alloys are brazed at around the melting temperature in most of the aluminium alloys. Therefore, the development of low temperature brazing filler alloys as well as superior strength Al alloys for various engineering applications is always in demand. In various heat exchangers and automotive applications, poor strength of Al alloys is due to the inherent porosities and casting defects. The unstable mechanical properties is therefore needed to be controlled by adding various additive elements in the aluminium and its alloys, by a change in the heat treatment procedure or by modifying the microstructure. In this regard, this article reports the effect of various elements added in aluminium alloys to improve microstructure, brazeability, machinability, castability as well as to stabilize the mechanical properties.

• Korean Journal of Crystallography
• /
• v.12 no.3
• /
• pp.177-181
• /
• 2001

We have studied superhydrophilic properties of TiO₂thin films in relation with those crystal structures due to the heat treatments. Thin films were fabricated on Si (100) wafers using a conventional Sol-Gel method. Following drying and sintering processes, TiO₂film had an anatase phase with additional heat treatment at 500℃, an rutile phase at 1000℃, and a mixture of anatase and rutile phase at 750℃. All these films got hydrophilic even without any UV illumination. Especially the sample treated at 750℃ had a superhydrophilic contact angle of 5°. We suggested that the superhydrophilic films should have a mixture of anatase and rutile phase for the best performance. The hydrophilic TiO₂films were slowly degraded into the hydrophobic state in the dark room but quickly recovered back with les than 1 hour of UV illumination.