• Physical Therapy Rehabilitation Science
• /
• v.10 no.1
• /
• pp.1-9
• /
• 2021

Objective: Joint mobilization for arthrokinematics altered by the positional fault of chronic ankle instability (CAI) is an effective intervention for stabilization. In this study, we compared the effects of ankle dorsi flexion range of motion (DFROM) and dynamic balance ability (DBA) in CAI patients via passive joint mobilization (PJM), a method traditionally performed in previous studies, and active joint mobilization (AJM), a method that can have a greater effect on cortical excitability with spontaneous movements. Design: Single-blind two-arm randomized controlled trial Methods: A total of 30 participants were registered: 15 each to the PJM and AJM groups. Each participant received a total of 10 intervention sessions, 10 minutes per session, 5 times a week for 2 weeks. PJM used Maitland's mobilization method to apply joint mobilization with talus in the posterior direction and AJM used an angular joint motion to induce patient's voluntary motion of medial malleolus anterior gliding and lateral malleolus posterior gliding, respectively. DFROM of the ankle was measured by using tape and DBA was evaluated by using the balance system. Results: Significant improvement was observed after intervention in both the PJM and AJM groups except for the DBA-anterior and DBA-right variables of the PJM group. There were statistically significant differences between the AJM and PJM groups in the DFROM, DBA-anterior, DBA-posterior, and DBA-right variables. Conclusions: The overall improvement of DFROM and DBA was found to be more effective in joint mobilization including voluntary movement. When it is accompanied by voluntary movement, it further affects the neuromuscular system of the ankle.

• Journal of Internet of Things and Convergence
• /
• v.8 no.5
• /
• pp.41-46
• /
• 2022

This study analyzed the results and implications of the industry-university cooperation human resource nurturing process based on the I-O model for the Motion Graphics major and the Global Hotelier major in Baek seok University. In this study, based on the analysis of the human resources training performance through industry-university cooperation in the motion graphics and hotelier fields for 5 years, what kind of efforts were made for successful human resource training, and the level of performance was analyzed and improvement points were suggested. In this study, four strategies were set for successful industry-university-tailored human resource nurturing: student-industry matching through industry participation in education, industry-university integrated education, education quality advancement, and customized education infrastructure construction. As a result of the analysis, customized human resource training should first be developed through industry demand survey and a mirror-type practice room should be built to fit the corporate environment. Second, it was found that it is possible to be individual only if there is an active participation of industry experts throughout the curriculum such as subjects and non-subjects.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.21 no.5
• /
• pp.465-474
• /
• 2008

The real-time hybrid testing method(RT-HYTEM) is a structural testing technique in which the numerical integration of the equation of motion for a numerical substructure and the physical testing for an experimental substructure are performed simultaneously in real-time. This study presents the quantitative evaluation of the seismic performance of a building structure installed with an passive and semi-active MR damper by using RT-HYTEM. The building model that was identified from the force-vibration testing results of a real-scaled 5-story building is used as the numerical substructure, and an MR damper corresponding to an experimental substructure is physically tested by using the universal testing machine(UTM). The RT-HYTEM implemented in this study is validated because the real-time hybrid testing results obtained by application of sinusoidal and earthquake excitations and the corresponding analytical results obtained by using the Bouc-Wen model as the control force of the MR damper respect to input currents were in good agreement. Also for preliminary study, some semi-active control algorithms were applied to the MR damper in order to control the structural responses optimally. Comparing between the test results of semi-active control using RT-HYTEM and numerical analysis results show that the RT-HYTEM is more resonable than numerical analysis to evaluate the performance of semi-active control algorithms.

• Cartoon and Animation Studies
• /
• s.25
• /
• pp.41-63
• /
• 2011

Many educational facilities have been formed due to the nation's revival policy in the animation industry since about 1995. Owed to the active financial support of the nation, the production industry rapidly vitalized, production technology rapidly advanced, and a large workforce is being passed on into society through educational institutions. The reality of many developing countries appearing to be putting emphasis on the industrialization of animation, similar to our country, is becoming a great pressure on us industrially. It is never easy to develop a certain field into a globally competitive industry in a short period of time. Our countermeasure, pursuant to these international circumstances, lies in innovation and creativity that has broken away from the existing methods of production, and mass production of high quality animation specialists. This paper is a new educational proposition for the consolidation of national competitiveness. Animating, the core of producing an animation, completely depends on the animator's artistic and technical ability. In order to supplement the existing methods of studying by theory and make up for the biggest weak point, which is the lack of "on the scene" learning contents, I propose incorporating movements based on frequently appearing characters in popular animations and acting them out slowly and including the "Slow Motion" kinetic effect, a way of enabling someone to learn and sense astrodynamic fundamental principles by oneself. It is a new method of learning movement, a plan made to achieve sensual performance gestures, and an improvement in direction for students who wish to become animators in the future.

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.7 no.2
• /
• pp.41-46
• /
• 2013

IIn this paper, active trasfemoral prosthesis leg is designed for the handicapped who lost their legs upon knee. It is important to design proper knee joint to mimic walking motion of hyman. 1 degree-of-freedom active trasfemoral prosthesis leg is designed with knee joint. Operating angle and torque have been calculated using kinematics of three linkages in prosthesis leg. Finite element analysis of major components is performed to evaluate the safety under operating condition and to reduce weights. Minimum volumes of components are obtained by optimization as satisfying safety requirements. The results show that about 35% of weight of components is reduced.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.4
• /
• pp.383-392
• /
• 2012

This paper reports the active vibration control of plates using a positive position feedback(PPF) controller with moment pair actuators. The equations of motion of the plates under a force and moment pairs are derived and the equations of PPF controllers are formulated. The numerical active control system is then achieved. The effect of the parameters - gain and damping ratio - of the PPF controllers on the open loop transfer function was investigated mainly in terms of the system stability. Increasing the gain of the PPF controller tuned at a mode, the magnitude of the open loop transfer function is increased at all frequencies without changing the phase behavior. The increase of the damping ratio of the PPF controller leads to decrease the magnitude of the open loop transfer function and to modify its phase characteristics, ie, system stability. Based on the behavior of the gain and the damping ratio of the controller, PPF controller for reduction of the plate vibration can be achieved. Two PPF controllers are designed with their connection in parallel to control the two modes simultaneously. Each PPF controller is tuned at the $1^{st}$ and $2^{nd}$ modes, respectively. Their parameters were determined to remain the system to be stable based on the results of the parametric study. A significant reduction in vibration at the tuned modes can be obtained.

• International Journal of Aeronautical and Space Sciences
• /
• v.8 no.2
• /
• pp.11-16
• /
• 2007

This paper describes the cycloidal wind turbine, which is a straight blade vertical axis wind turbine using the cycloidal blade system. Cycloidal blade system consists of several blades rotating about an axis in parallel direction. Each blade changes its pitch angle periodically. Cycloidal wind turbine is different from the previous turbines. The wind turbine operates with optimum rotating forces through active control of the blade to change pitch angle and phase angle according to the changes of wind direction and wind speed. Various numerical experiments were conducted to develop a small vertical axis wind turbine of 1 kW class. For this numerical analysis, the rotor system equips four blades consisting of a symmetric airfoil NACA0018 of 1.0m in span, 0.22m in chord and 1.0m in radius. A general purpose commercial CFD program, STAR-CD, was used for numerical analysis. PCL of MSC/PATRAN was used for efficient parametric auto mesh generation. Variables of wind speed, pitch angle, phase angle and rotating speed were set in the numerical experiments. The generated power was obtained according to the various combinations of these variables. Optimal pitch angle and phase angle of cycloidal blade system were obtained according to the change of the wind direction and the wind speed. Based on data obtained from the above analysis, control device was designed. The wind direction and the wind speed were sensed by a wind indicator and an anemometer. Each blades were actuated to optimal performance values by servo motors.

• Fashion & Textile Research Journal
• /
• v.17 no.6
• /
• pp.881-894
• /
• 2015

The silver generation have clothing style of optimal daily life comparing than young generation because they do not participate a specific sport event but daily- life exercise. As the human body ages, the figure of the silver generation shows different body shape because upper body changes to curved figure including the belly and waist part. Therefore, clothing characteristics for the silver generation should be considered with proper function, design and textiles to optimize body movement. This study investigated various exercise types according to motion analysis of the silver generation in order to develop the design of the active T-shirts reflecting the structural properties and providing the optimum exercise circumstance. The results to consider design needs are as followed; As the T-shirts design for the flexible exercise which required frequent movement of upper body such as bending and waist twisting during body stretching, a stretch fabric applied to the waist part considering T-shirts allowance and length to make extreme elongation and support for well-fitting appearance of the T-shirts. As the T-shirts design for the instantaneous reactionary exercise, high elastic four-way stretch fabric is applied to the part of arm hole to optimize skeletal and muscle movement for entire body and arm work. As the T-shirts design for the endurance exercise such as climbing, cycling, and walking, the shoulder line of the back part has cutting line allowance to make optimum movement of the upper body but no change of the waist part.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.9 no.1 s.41
• /
• pp.61-70
• /
• 2005

Shaking table tests are carried out on a single-degree-of-freedom mass that is equipped with a hybrid base isolation system. The isolator consists of a set of four specially-designed friction pendulum systems (FPS) and a magnetorheological (MR) damper. The structure and its hybrid isolation system are subjected to various intensities of near- and far-fault earthquakes on a large shake table. The proposed fuzzy controller uses feedback from displacement or acceleration transducers attached to the structure to modulate resistance of the semi-active damper to motion. Results from several types of passive and semi-active control strategies are summarized and compared. The study shows that a combination of FPS isolators and an adjustable MR damper can effectively provide robust control of vibration for a large full-scale structure undergoing a wide variety of seismic loads.

• The Journal of Korean Academy of Orthopedic Manual Physical Therapy
• /
• v.5 no.1
• /
• pp.39-51
• /
• 1999

Background and Purpose. Objective measurements of hamstring muscle length are needed to quantify baseline limitations and to document the effectiveness of therapeutic interventions. Several indirect clinical tests for measuring hamstring muscle length are available, but influence of their test procedure is not well documented. The purpose of this study were 1) to describe hamstring muscle length as reflected by use of six tests(active straight leg raising(ASLR), passive straight leg raising(PSLR), passive straight leg raising with the lower back flat(PSLRB), active knee extension(AKE), passive knee extension(PKE), hip joint angle(HJA). 2) to examine the correlation among the tests. Subjects, Sixty subjects(30 men. 30 women) ranging in age from 18 to 25 years(mean 20.2 years) and with no limitation hamstring flexibility and no neurological and orthopedical problems. Methods. All subjects performed six tests. A inclinometer was used to determine the end point of range of motion. HJA was measured using an inclinometer placed over the sacrum. PSLRB were tested PSLR with the low back flat and the opposite thigh slightly flexed and support on pillows. Results, A mean ASLR value of 85.9 degrees, PSLR value of 99.9 degrees, PSLRB value of 109.8 degrees, AKE value of 77.2 degrees PKE value of 83.1 degrees and HJA value of 73.0 degrees were obtained for all subjects. A dependent t-test showed significant difference between the angles of ASLR and PSLR(p<0.001). There was a significant difference between the angles of PSLR and PSLRB(p<0.001). There was a significant difference between the angles of AKE and PKE(p<0.001). The highest correlation was between PSLR and PSLRB(r=0.915, p<0.001). All SLR tests were significants related(p<0.001), as well as AKE and PKE(p<0.001). The lowest correlation was between PKE and HJA(r=0.171. p>0.05). Conclusion and Discussion. The results indicated that the hip flexion angles for ASLR, PSLR and PSLRB were a difference, and the knee extension angles for AKE and PKE were a difference.