• Transactions on Electrical and Electronic Materials
• /
• 제15권2호
• /
• pp.81-86
• /
• 2014

The process parameter in optimized KOH alkali activation of soft carbon series coke material in high purity was set with DOE experiments design. The activated carbon was produced by performing the activation process based on the set process parameters. The specific surface area was measured and pore size was analyzed by $N_2$ absorption method for the produced activated carbon. The surface functional group was analyzed by Boehm method and metal impurities were analyzed by XRF method. The specific surface area was increased over 2,000 $m^2/g$ as the mixing ratio of activation agent increased. The micro pores in $5{\sim}15{\AA}$ and surface functional group under 0.4 meq/g were obtained. The contents of the metal impurity in activated carbon which is the factor for reducing the electrochemical characteristics was reduced less than 100 ppm through the cleansing process optimization. The electrochemical characteristics of activated carbon in 38.5 F/g and 26.6 F/cc were checked through the impedance measuring with cyclic voltammetry scan rate in 50~300 mV/s and frequency in 10 mHz ~100 kHz. The activated carbon was made in the optimized activation process conditions of activation time in 40 minutes, mixing ratio of activation agent in 4.5 : 1.0 and heat treatment temperature over $650^{\circ}C$.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2003년도 추계학술대회 논문집
• /
• pp.146-151
• /
• 2003

Reduced Activation Ferritic/Martenstic (RAFs) are leading candidates for structural materials of D-T fusion reactor. One of The RAFs, JLF-1 (9Cr-2W-V, Ta) has been developed and proved to have good resistance against high-fluency neutrino irradiation and good phase stability. Recently, in order to clarify the strengthening mechanical at high temperature, a new scheme to improve high temperature mechanical properties is desired. Therefore, the creep properties and creep life prediction by Larson-Miller Parameter method for JLF-1 to be used for fusion reactor materials or other high temperature components were presented at the elevated temperatures of $500^{\circ}C$, $550^{\circ}C$, $600^{\circ}C$, $650^{\circ}C$ and $704^{\circ}C$. It was confirmed experimentally and quantitatively that a creep life predictive e벼ation at such various high temperatures was well derived by LMP.

• 한국압력기기공학회 논문집
• /
• 제16권1호
• /
• pp.49-55
• /
• 2020

Creep rupture data for Alloy 690 steam generator tubes in a pressurized water reactor are essentially needed to demonstrate a severe accident scenario on thermally-induced tube failures caused by hot gases in a damaged reactor core. The rupture data were obtained using the tube specimens under different applied-stress levels at 650℃, 700℃, 750℃, 800℃, and 850℃. Important creep constants were proposed using various creep laws in terms of Norton power law, Monkman-Grant (M-G) relation, damage tolerance factor (λ), and Zener-Hollomon parameter (Z). In addition, a creep activation energy (Q) value for Alloy 690 tube was reasonably determined using experimental data. Creep behaviors such as creep strength, creep rates, rupture elongation showed the results of temperature dependence well. Modified M-G plot improved a correlation of the creep rate and rupture life. Damage tolerance factor for Alloy 690 tubes was found to be λ =2.20 in an average value. Creep activation energy for Alloy 690 tube was optimized for Q=350 (kJ/mol). A plot of Z parameter obeyed a good linearity, and the same creep mechanism was inferred to be operative in the present test conditions.

• 한국해양공학회지
• /
• 제18권2호
• /
• pp.58-63
• /
• 2004

Reduced Activation Ferritic/Martensitic Steels (RAFs) are leading candidntes for structural materials of a D-T fusion reactor. One of the RAFs, JLF-l (9Cr-2W-V, Ta) has been developed and has shown to have good resistance against high-fluency neutrino irradiation and good phase stability. Recently, in order to clarify the strengthening mechanisms at high temperatures, a new scheme to improve high temperature mechanical properties is desired. Therefore, the test technique development of high temperature creep behaviors for this material is very important. In this paper, the creep properties and creep life prediction, using the Larson-Miler parameter method for JLF-l to be used for fusion reactor materials or other high temperature components, are presented at the elevated temperatures of 50$0^{\circ}C$, 55$0^{\circ}C$, $600^{\circ}C$, $650^{\circ}C$ and 704$^{\circ}C$. It was confirmed, experimentally and quantitatively, that a creep life predictive equation, at such various high temperatures, is well derived mr the LMP method.

• 한국해양공학회지
• /
• 제25권4호
• /
• pp.12-17
• /
• 2011

Little design data is available for the creep life prediction of 9% Ni alloy in elevated temperatures. Therefore, in this study, a series of creep tests under 16 combined conditions with 4 kinds of stresses and 4 temperatures was performed to obtain creep design and life prediction data for 9% Ni alloy, with the following results. The stress exponents decreased as the test temperature increased. The creep activation energy gradually decreased as the stresses became larger. The Larson-Miller parameter (LMP) constant for this alloy was estimated to be about 2.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 A
• /
• pp.480-483
• /
• 1992

Although the back-propagation(BP) algorithm is widely used for its simple structure and easy learning method, it has a drawback of slow convergence rate. In this paper, we propose an algorithm to improve this problem by manipulating the slope parameter of the activation function. The steepest descent method is used in learning the slope parameter, as in the case of weight. The simulation shows that the learning rates of the proposed algorithm is faster than the conventional BP algorithm.

• 대한화학회지
• /
• 제9권1호
• /
• pp.23-28
• /
• 1965

90% ethanol solution에서 benzyl chloride와 radioactive chloride($^{36}Cl^-$)와의 exchange를 反應速度論的으로 硏究하였으며 그 結果로 交換反應은 typical bimolecular reaction임을 알았고 그 activation parameter들은 각기 다음과 같았다. ${\Delta}H^{\neq}$= 18.50 Kcal ${\Delta}S^{\neq}$= -22.09 e.u. 특히 本實驗 缺課와 다른 實驗結果를 綜合討論함으로써 反應速度는 attacking anion의 nuclephilic ability에 크게 관계 됨을 입증할 수 있었으며 또한 exchange reaction에 있어서 halide들의 reactivity의 순서는 bond dissociation energy의 差로써 보다는 오히려 Swain의 nucleophilic parameter(n)로써 설명함이 더욱 타당함을 알았다.

• Smart Structures and Systems
• /
• 제28권6호
• /
• pp.791-798
• /
• 2021

Current investigation aims to analyze the characteristics of magnetohydrodynamic boundary layer flow of bioconvection Casson fluid in the presence of nano-size particles over a permeable and non-linear stretchable surface. Fluid passes through the Darcy-Forchheimer permeable medium. Effect of different parameter such as Darcy-Forchheimer, porosity parameter, magnetic parameter and Brownian factor are investigated. Increasing Brownian factor leads to the rapid random movement of nanosize particles in fluid flows which shows an expansion in thermal boundary layer and enhances the nanofluid temperature more rapidly. For large values of Darcy-Forchheimer, magnetic parameter and porosity factor the velocity profile decreases. Higher values of velocity slip parameter cause decreasing trend in momentum layer with velocity profile.

• Advances in Energy Research
• /
• 제8권4호
• /
• pp.253-264
• /
• 2022

This paper deals with the effects of design (active area, current density, membrane conductivity) and operating parameters (temperature, relative humidity) on the performance of hydrogen-fuelled proton exchange membrane (PEM) fuel cell. The design parameter of a PEM fuel cell with the active area of the single cell considered in this study is 25 cm² (5 × 5). The operating voltage and current density of the fuel cell were 0.7 V and 0.5 A/cm² respectively. The variations of activation voltage, ohmic voltage, and concentration voltage with respect to current density are analyzed in detail. The membrane conductivity with variable relative humidity is also analyzed. The results show that the maximum activation overpotential of the fuel cell was 0.4358 V at 0.21 A/cm² due to slow reaction kinetics. The calculated ohmic and concentrated overpotential in the fuel cell was 0.01395 V at 0.76 A/cm² and 0.027 V at 1.46 A/cm² respectively.

• 공업화학
• /
• 제9권4호
• /
• pp.509-515
• /
• 1998

커피폐기물을 원료로 하여 염화아연으로 화학적 활성화시켜 커피활성탄 (activated coffee char)을 제조하였다. 이 연구는 roasting과정, 탄화과정, 활성화, 그리고 수세 및 건조의 공정으로 수행되었다. Roasting 과정은 $300{\sim}400^{\circ}C$에서 10분간 수행되었다. 탄화과정의 적절한 조건은 $650^{\circ}C$에서 1시간인 것으로 나타났다. 화학적 활성화에 있어서 가장 중요한 parameter는 활성화제와 coffee char의 화학비인 것을 알 수 있었다. $N_2$ gas를 이용하여 77K에서 제조된 커피활성탄의 BET 비표면적과 BJH 세공용적을 측정하였다. 염화아연에 의해 활성화되어 제조된 coffee char의 비표면적이 $1110{\sim}1580m^2/g$로 분석되었으며 세공용적은 $0.51{\sim}0.81cm^3/g$로 각각 분석되었다. SEM은 세공과 coffee char의 표면관찰에 이용되었다. 분석결과, 활성화 표면과 많은 세공이 형성되어 있는 것을 보였다. 커피폐기물을 이용한 activated coffee char의 제조가 성공적으로 수행되었으며, 이는 폐기물을 이용한 자원 개발의 가능성을 보여주었다.