• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.140-140
• /
• 2010

Non-mass analyzed ion shower doping (ISD) technique with a bucket-type ion source or mass-analyzed ion implantation with a ribbon beam-type has been used for source/drain doping, for LDD (lightly-doped-drain) formation, and for channel doping in fabrication of low-temperature poly-Si thin-film transistors (LTPS-TFT's). We reported an abnormal activation behavior in boron doped poly-Si where reverse annealing, the loss of electrically active boron concentration, was found in the temperature ranges between $400^{\circ}C$ and $650^{\circ}C$ using isochronal furnace annealing. We also reported reverse annealing behavior of sequential lateral solidification (SLS) poly-Si using isothermal rapid thermal annealing (RTA). We report here the importance of implantation conditions on the dopant activation. Through-doping conditions with higher energies and doses were intentionally chosen to understand reverse annealing behavior. We observed that the implantation condition plays a critical role on dopant activation. We found a certain implantation condition with which the sheet resistance is not changed at all upon activation annealing.

• Korean Journal of Materials Research
• /
• v.18 no.10
• /
• pp.552-556
• /
• 2008

Modified thermal annealing was applied to the activation of the polycrystalline silicon films doped as p-type through implantation of $B_2H_6$. The statistical design of experiments was successfully employed to investigate the effect of rapid thermal annealing on activation of polycrystalline Si doped as p-type. In this design, the input variables are furnace temperature, power of halogen lamps, and alternating magnetic field. The degree of ion activation was evaluated as a function of processing variables, using Hall effect measurements and Raman spectroscopy. The main effects were estimated to be furnace temperature and RTA power in increasing conductivity, explained by recrystallization of doped ions and change of an amorphous Si into a crystalline Si lattice. The ion activation using rapid thermal annealing is proven to be a highly efficient process in low temperature polycrystalline Si technology.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.346-349
• /
• 2002

High Power and high dose ion implantation is essentially needed to make power MOSFET devices based on SiC wafers, because the diffusivities of the impurities such as Al, N, p, B in SiC crystal are very low. In addition, it is needed high temperature annealing for electrical activation of the implanted species. Due to the very high annealing temperature, the surface morphology after electrical activation annealing becomes very rough. We have found the different surface morphologies between implanted and unimplanted region. The unimplanted region showed smoother surface morphology It implies that the damage induced by high energy ion implantation affects the roughening mechanism. Some parts of Si-C bonding are broken in the damaged layer, s\ulcorner the surface migration and sublimation become easy. Therefore the macrostep formation will be promoted. N-type 4H-SiC wafers, which were Al ion implanted at acceleration energy ranged from 30kev to 360kev, were activated at 1600$^{\circ}C$ for 30min. The pre-activation annealing for damage relaxation was performed at 1100-1500$^{\circ}C$ for 30min. The surface morphologies of pre-activation annealed and activation annealed were characterized by atomic force microscopy(AFM).

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08b
• /
• pp.1277-1280
• /
• 2007

Isothermal activation annealing was carried out using boron doped SLS poly-using an RTA system. We observed different behavior of reverse annealing depending on the implantation conditions.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.752-755
• /
• 2006

Reverse annealing was observed in $P^+/B^+$ ion shower doped poly-Si upon activation annealing. Phosphorous or boron was implanted by ion shower doping using a source gas mixture of $PH_3/H_2$ or $B_2H_6/H_2$. Activation annealing was conducted using a tube furnace in the temperature ranges from $350^{\circ}C$ to $650^{\circ}C$. Hall measurement revealed that reverse annealing begins at different annealing temperatures for poly-Si implanted with P and B, respectively. It was observed that reverse annealing starts at $550^{\circ}C$$ in $P^+$ ion shower doped poly-Si, while at $350^{\circ}C$ in the case of B-doping.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.264-267
• /
• 2008

Through-doping conditions with higher energies and doses were intentionally chosen to understand reverse annealing behavior. We observed that the implantation condition plays a critical role on dopant activation. We found a certain implantation condition with which the sheet resistance is not changed at all upon activation annealing.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.376-376
• /
• 2012

본 연구는 Poly-Si에 이온 주입된 Boron의 Activation 거동을 연구하고자 SLS (Sequential Lateral Solidification) Poly-Si과 ELA (Excimer Laser Annealing) Poly-Si의 활성화 거동을 비교 분석하였다. SLS 및 ELA 결정화 방법으로 제조된 Poly-Si을 모재로 비 질량 분리 방식의 ISD (Ion Shower Doping) System을 사용하여 2.5~7.0 kV까지 이온주입 하였다. 이온주입 후 두 가지의 열처리 방법, 즉, FA 열처리(Furnace Annealing)와 RTA 열처리(Rapid Thermal Annealing)를 사용하여 도펀트 활성화 열처리를 수행하고 이온주입 조건 및 활성화 열처리 방법에 따른 결함 회복 및 도펀트 활성화 거동의 변화를 관찰하였다. TRIM-code Simulation 결과 가속 이온 에너지와 조사량이 증가 할수록 이온주입 시 발생하는 결함의 양이 증가하는 것을 정량적으로 계산하였다. 실험 결과 결함의 양이 증가 할수록 Activation이 잘되는 것을 관찰할 수 있었다. SLS Poly-Si에 비하여 ELA Poly-Si의 경우 도펀트 활성화 열처리 후 활성화 효율이 높게 나타났다. 본 결과는 Grain Boundary의 역할과 밀접한 관계가 있으며 간단한 정성적인 Model을 제시하였다. 활성화 효율의 경우 RTA 열처리 시편이 FA 시편에 비하여 높은 것이 관찰되었다. 본 결과는 열처리 온도 및 시간에 따라 변화하는 Boron의 특이한 활성화 거동인 Reverse Annealing 효과에 기인하는 것으로 규명되었다.

• Korean Journal of Materials Research
• /
• v.13 no.11
• /
• pp.721-724
• /
• 2003

A Fe-Si-B-Ni amorphous alloy manufactured by one roll melt-spinning method showed the crystallization temperature difference of a maximum $10^{\circ}C$ according to each lot. This temperature difference had a considerable influence on the annealing process to be conducted for obtaining the proper inductance of the alloy. The proper annealing temperature of the alloy was $480^{\circ}C$ and the annealing time increased as the crystallization temperature increased. The activation energy measured by Kissinger method increased as the crystallization temperature increased. Therefore, the annealing process must be adjusted by the crystallization temperature difference of the amorphous alloy.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.907-909
• /
• 2003

We report a novel method of activation-annealing, named as induction annealing (IA). IA is realized by applying alternating electric field induced by alternatingmagnetic filed applied to the sample. We observed the enhanced kinetics of dopant activation by using IA.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1630-1632
• /
• 1997

We have investigated activation phenomena of implanted ions on silicon wafers using microwave(2.45GHz). It is found that the higher concentration of impurities makes the better activation effects by microwave annealing. We have exposed poly-Si TFTs by microwave in order to anneal and improved the device performance. Microwave activates source/drain ions and lowers the contact resistance so that the current of the poly-Si TFTs increases. In addition, the leakage current of hydrogen passivated poly-Si TFTs is decreased after microwave annealing, due to the diffusion of hydrogen ions and curing the defects in the poly-Si active channel.