• Macromolecular Research
• /
• 제16권2호
• /
• pp.128-133
• /
• 2008

Several dual-curable acrylic pressure-sensitive adhesives (PSA) were synthesized by the radical polymerization of acrylic monomers containing benzophenone, hydroxyl, and alkyl groups. The optimum extent of UV-induced cure was determined by varying the content of the benzophenone groups (the photoinitiator) from 0.5 to 1.5 wt%. The weight average molecular weight of the polymers obtained ranged from 300,000 to 700,000 amu. The coated pressure-sensitive adhesives were cured either by short UV exposure to induce the grafting of acrylic polymers, or by heating for 6 hat $60^{\circ}C$ to promote the reactions between the polyisocyanates and hydroxyl groups. The dual-curing behavior was determined by monitoring both processes quantitatively by infrared spectroscopy. The developed dual-curable acrylic pressure-sensitive adhesives were found to compensate for the limitations in UV-induced curing of thick coatings.

• Elastomers and Composites
• /
• 제51권3호
• /
• pp.181-187
• /
• 2016

Transparent acrylic pressure sensitive adhesives (PSAs) were successfully prepared by photopolymerization with 2-ethylhexyl acrylate (2-EHA) and 2-hydroxyethyl acrylate (2-HEA) as a default constituent and with isobornyl acrylate (IBOA) and N-(isobutoxymethyl)acrylamide (IBMA) as a variable constituent. The IBMA mole fraction effect in the acrylic PSAs was investigated on adhesion performances and the optical properties including 85/85 test as well as the characteristics (solid content, and molecular weight) of the PSA syrups were also investigated. Regardless increasing the IBMA mole fraction in the acrylic PSAs, the acrylic PSAs exhibited almost the same adhesion performance such as $180^{\circ}$ peel strength (~4.0 kg/25 mm) and probe tack (~0.27 kg). All the acrylic PSA samples also showed high transmittance (more than 91%), low haze (less than 1.0%) and low color-difference (less than 1.0) before and after 85/85 test.

• Journal of Pharmaceutical Investigation
• /
• 제35권3호
• /
• pp.173-177
• /
• 2005

Addition of 30% propylene glycol was required to maintain sink condition in the evaluation of percutaneous absorption of estradiol and norethindrone acetate. The permeability of estradiol was higher in silicone and SIS adhesives. However, estradiol was crystallized in silicone, SIS, and SBS adhesive matrix. The permeability ratio of estradiol or norethindrone acetate from acrylic pressure sensitive adhesives varied widely depending on the functional group of the acrylic adhesives. PEO grafting to acrylic adhesive seemed to change physicochemical property of acrylic adhesive and increased the permeability of estradiol and norethindrone acetate significantly. On the contrary, highly cross-linked enhancer compatible acrylic adhesive decreased the permeability of both estradiol and norethindrone acetate. $Span^{\circledR}$ 20 provided the highest enhancing effect on the permeability of both estradiol and norethindrone acetate followed by oleic acid and $Crovol^{\circledR}$ EP40. The permeability of the drugs from the developed system was comparable to that from commercial $Combitran^{\circledR}$, although significantly lower amount of estradiol and norethindrone acetate were loaded in the developed system.

• 한국응용과학기술학회지
• /
• 제22권2호
• /
• pp.191-199
• /
• 2005

Removable protective adhesives for automobiles were synthesized by an emulsion polymerization of monomers such as n-butyl acrylate (BA), n-butyl methacrylate (BMA), acrylonitrile (AN), acrylic acid (AA) and 2-hydroxyethyl methacrylate (2-HEMA), in which AA and 2-HEMA were functional monomers. Potassium persulfate (KPS) was used as an initiator and sodium lauryl sulfate (SLS) was used as an emulsifier, and polyvinyl alcohol (PVA) was used as a stabilizer. Emulsion polymerization was carried out in a semi-batch type reactor. Tensile strength, extension, peel strength, viscosity and solid content of the synthesized adhesives were tested. The optimum physical properties of the removable protective adhesives for automobiles were obtained with the composition of 0.43 mole BA, 0.57 mole AN, 0.21 mole BMA, 0.03 mole AA, and 0.03 mole 2-HEMA.

• 한국응용과학기술학회지
• /
• 제37권6호
• /
• pp.1627-1634
• /
• 2020

본 연구에서는 수성 아크릴계 점착제의 물성에 대한 주 단량체의 측쇄 사슬의 영향을 비교하기 위해 주 단량체로 각각 ethyl acrylate, 2-ethylhexyl acrylate, lauryl methacrylate를 사용하여 acrylic acid, 2-hydroxyethyl acrylate와 공중합체를 합성하여 수성 아크릴 점착제를 제조하였다. 제조한 수성 아크릴 점착제의 고형분, 평균입도분포, 초기점착력, 최대점착력, 박리강도, 내열점착력 등의 물리적 특성을 비교하였다.

• 한국응용과학기술학회지
• /
• 제23권2호
• /
• pp.169-176
• /
• 2006

Acrylic adhesives for automobiles protection were prepared by emulsion polymerization. Monomers used were n-butyl acrylate(BA), acrylonitrile (AN), butyl methacrylate(BMA), glycidyl methacrylate(GMA), and acrylic acid (AA). Emulsifiers used were sodium lauryl sulfate and polyoxyethylene lauryl ether, which are an anionic emulsifier and a nonionic emulsifier respectively. Potassium persulfate was used as an initiator and polyvinyl alcohol was used as a stabilizer. Emulsion polymerization was carried out in a semi-batch reactor at $70^{\circ}C$ and agitation speed was kept at 200 rpm. Water resistance, heat resistance, acid resistance, alkali resistance and smoke resistance were examined. As a result, when each 0.03 mole of GMA and AA was introduced, the adhesion properties and various above mentioned resistances of the prepared adhesives were satisfied the standard for automobiles.

• 한국응용과학기술학회지
• /
• 제25권4호
• /
• pp.525-532
• /
• 2008

To prepare a solution type acrylic pressure-sensitive adhesive, quarter polymers were synthesized from butyl acrylate(BA), 2-ethylhexylacrylate(2-EHA) as a base monomer, methyl methacrylate(MMA) as a comonomer, each of methacrylic acid(MAA), acrylic acid(AA) as a functional monomer. Acrylic solution type pressure-sensitive adhesives(PSA's) of isocyanate derivative crosslinking PSA's were prepared by crosslinking of BEMM, BEMA with toluene-2,4-diisocyanate. The structure of adhesive was identified by FT-IR. The viscosity was measured by using Brookfield DV-III and molecular weight was measured by using gel permeation chromatography. The physical properties of polyethylene film coated with BEMMT, BEMAT were measured as a function of the concentration. As the result, BEMMT(0.6, 0.8), BEMAT(0.6) showed peel adhesion of $160{\sim}180\;g_f$/25 mm width and shear adhesion of more than 24 hours, and tackiness of $4/32{\sim}6/32$ which was relevant to commercial usage.

• 접착 및 계면
• /
• 제14권1호
• /
• pp.43-48
• /
• 2013

압력감응성 아크릴 점착제의 물성은 가교를 위한 관능성그룹을 가진 단량체를 이용하여 쉽게 물성을 조절할 수 있다. 본 연구에서는 두개의 다른 가교제, isocyanate 및 epoxy형 가교제에 따른 아크릴 점착제의 가교특성과 물성을 연구하였다. 2-Ethylhexyl acrylate, acrylic acid (AA)와 2-hydroxyethyl methacrylate를 주 단량체로 하여 이소시아네이트 또는 에폭시형 가교제로 가교한 점착제의 박리점착 특성, 볼텍, 유지력 및 수축성을 고찰하였다. 점착특성은 AA함량 증가와 더불어 증가하였고 가교점이 많고 ether와 같은 유연한 결합을 생성하는 에폭시형 가교제에서 우수한 물성을 나타내었다.

• Journal of Pharmaceutical Investigation
• /
• 제38권4호
• /
• pp.223-228
• /
• 2008

The purpose of this study was to investigate the feasibility of developing transdermal drug delivery system (TDDS) for fentanyl used for the management of chronic cancer pain. The effect of type of pressure sensitive adhesive on the permeation of fentanyl from polyisobutylene (PIB), silicone and acrylic adhesive was evaluated. Due to the good adhesive force and relatively steady flux for 3 days, both acrylic and PIB adhesives were chosen for further study. The permeation rate of fentanyl was the highest from acrylic adhesive with hydroxyl functional group. Permeation rate increased linearly as the concentration of fentanyl in acrylic adhesive was increased from 2.5% to 10%. In case of PIB adhesive, crystals of fentanyl were developed above 5% drug load. $Crovol^{(R)}$ A40, $Crovol^{(R)}$ PK40 and Plurol $oleique^{(R)}$ provided higher flux of fentanyl.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.651-652
• /
• 2010