• The Journal of the Acoustical Society of Korea
• /
• v.34 no.3
• /
• pp.219-226
• /
• 2015

In this paper, derivation of the STL (Sound Transmission Loss) of a square plate installed in an impedance tube is discussed using an analytic method. Coupled motion of the plate vibration and acoustic field is considered. Vibration of the plate and pressure field inside the tube are expressed in terms of the infinite series of modal functions. Under the plane wave assumption, it is shown that consideration of the first few modes yields sufficiently accurate results. When the boundary of the plate is clamped, vibration mode is assumed as a multiplication of the beam modes corresponding to the crosswise directions. The natural frequencies of the clamped plate are calculated using the Rayleigh-Ritz method. It is found that the STL shows a dip at the lowest natural frequency of the plate, and increases as the frequency decreases below the natural frequency. Comparison of the result in this paper with the STL obtained by measurements and FE computations in the reference shows an excellent agreement.

• The Journal of the Acoustical Society of Korea
• /
• v.8 no.4
• /
• pp.29-38
• /
• 1989

Detection of an underwater target by acoustic wave raises various difficulties due to unpredictable noise interference which originates from clutter, reverberation, and variations of medium characteristics with time and location. The SNR and the range resolution of conventional SONAR systems using a matched filter are generally poor, since the latter is optimum only in the additive white noise case. Furthermore, it cannot compensate for variations of the detection level which are responsible for the resultant detection errors. In this paper, the unpredictable interferences are compensated for by using an adaptive filter. It recursively estimates the channel impulse response based on the received echo signal. In the low noise environments, the estimated impulse response is close to the true one, providing a good range resolution, and a matched filter is used subsequently for the purpose of detection. It is shown through computer simulation that good performance can be achieved via the two steps of filtering. Also, the detection level remains unchanged without any additional provisions. Finally, we present the characteristics of the employed adaptive filter parameters.

• The Journal of the Acoustical Society of Korea
• /
• v.25 no.3E
• /
• pp.115-122
• /
• 2006

The bistatic scattering of an incident wave by a hemi-spherically capped cylinder is of particular interest because it has rarely been studied until the present day. The configuration of a hemi-spherically capped cylinder is similar to naval underwater weapons (submarines, mines, torpedos, etc.), but which is not exactly the same. This paper describes a novel laboratory experiment aimed at direct measurement of bistatic scattering by a hemi-spherically capped cylinder. Bistatic scattering by a hemi-spherically capped cylinder was measured in an acoustic water tank (5m long, 5m wide, 5m deep) using a high frequency projector (120kHz) and hydrophone. Measurements of monostatic scattering were also made under the same conditions. The bistatic scattering pattern by a hemi-spherically capped cylinder was measured against the incident angles $(0^{\circ},\;15^{\circ},\;20^{\circ},\;30^{\circ},\;45^{\circ},\;60^{\circ},\;90^{\circ})$ in order to verify various scattering pattern characteristics by the change of incident angle. The results indicate that the bistatic scattering TS at a wide scattering angle is much stronger than the mono static scattering TS. In bistatic scattering, the forward scattering TS is significantly stronger than the backward scattering TS, and the forward scattering pattern is also broader. In case of seven incident angles, the maximum value of forward scattering TS is about 14dB stronger than that of backward scattering TS. It is also found that forward scattering varies with the incident angle of sound to a much less extent than backscattering, and it is not seriously affected by the incident angle. These features could be the advantages of using forward scattering for detecting underwater targets at long range and increasing detection area and probability.

• The Journal of the Acoustical Society of Korea
• /
• v.34 no.6
• /
• pp.487-492
• /
• 2015

A short-range underwater target detection and identification techniques using mid- and high-frequency bands have been highly developed. However, nowadays the long-range detection using the low-frequency band is requested and one of the most challengeable issues. The waveform inversion technique is widely used and the hottest technology in both academia and industry of the seismic exploration. It is based on the numerical analysis tool, and could construct more than a few kilometers of the subsurface structures and model-parameters such as P-wave velocity using a low-frequency band. By applying this technique to the underwater acoustic circumstance, firstly application of underwater target detection is verified. Furthermore, subsurface structures and it's parameters of the war-field are well reconstructed. We can confirm that this technique greatly reduces the false-alarm rate for the underwater targets because it could accurately reproduce both the shape and the model-parameters at the same time.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.231-235
• /
• 2009

The mainly objectives of this study was a combustion dynamics and instability characteristics in a model dump type combustor which is scale down of GE 7FA+e DLN 2.6 gas turbine combustor with running at Seo-Inchon combined cycle power plant. Model gas turbine injector has 2-stage swirl vane and it's reduced 1/3 size of the original one. The shape of plenum and combustor were designed for similar acoustic characteristics. As the result, this research have been shows the peak frequency of model combustor was changed quarter-wave mode to Helmholtz resonator mode in plenum and longitudinal mode in dump combustor at unstable flame conditions caused by the different of combustor temperature and fuel-air mixture distributions.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.05a
• /
• pp.343-345
• /
• 2015

Currently, SAW Device has been used as a frequency filter using the property of passing only a desired frequency with a narrow bandwidth. However, the areas of activity in various fields since the permanent advantages can be widened by using a non-powered. These sensor tags using SAW Device has been done, but a lot of research, the development of the state still insufficient for Reader Platform. How to read the value of the ID Tag Using SAW Device has a time domain sampling (TDS) method and a frequency domain sampling (FDS) method. The purpose of the paper, we use the FDS method that requires high-speed processing with a relatively slow sampling rate does not require high-speed sampling. Reader Platform was the way to detect ID through PC as FDS way, but It is based on the Cortex-A9 processor and it works a low price, compact and real-time Reader Platform.

• Journal of the Korean Ceramic Society
• /
• v.40 no.6
• /
• pp.539-546
• /
• 2003

The GaN/sapphire layered structure is a potential candidate for high frequency devices due to high acoustic velocity of sapphire. Generally, the GaN thin films are epitaxially grown on c, a, and r-plane sapphire substrates. In this study, wave equations of GaN/sapphire structure were calculated according to crystallographic relationship between GaN layer and sapphire substrate. On each plane, the shear velocity was changed by the kH of GaN layer and propagation direction on sapphire substrate. We found electromechanical coupling constant of r-plane was better than the others. As a result, elastic stiffness and electromechanical coupling constant of materials are affected by a cut and an orientation of substrate. GaN/r-plane sapphire structure is more advantageous for high frequency SAW devices.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.47 no.5
• /
• pp.212-221
• /
• 2010

The bubbles could be created from multiple source in the surface of ocean. The bubbles which are created like this affect to the intensity and the sound speed of acoustic wave which are used from the ocean. From the research, it observed Reverberation from the sea surface, using Vbeam transmission and reception equipment that was a cross-shaped Array, from 2008 July 2nd to July 3rd at 4Km from the East Sea Mookho port. It is difficult to analyze data because the received signal has ambient noise and occurrence ISI(Inter Symbol Interference) for multipath. This paper remove that ambient noise and ISI using the directions of arrival beamforming and the filter and sum beamforming. After beamforming, a following DFE(Decision Feedback Equalizer) removes the remaining multipath components. Experimental results show that the proposed technique reduce the errors caused by ISI.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.11 s.353
• /
• pp.8-13
• /
• 2006

Recent RF SAW filters are made using a HTCC package with a CSP(chip scale Package) technology. This paper describes a development of a new $1.4{\times}1.1\;and\;2.0{\times}1.4mm$ RF SAW liters made by PCB substrate instead of HTCC package, and this technology can reduce the cost of materials down to 40%. We have investigated the multi-layered PCB substrate structures and raw materials to find out the optimal flip-bonding condition between the $LiTaO_3$ wafer and PCB substrates. Also the optimal materials and processing conditions of epoxy laminating film were found out through the experiments which can reduce the bending moment caused by the difference of the thermal expansion between the PCB substrate and laminating film. The new PCB SAW filter shows good electrical and reliability performances with respect to the present SAW filters.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.5
• /
• pp.497-503
• /
• 2016

In this study, we formulate an acoustical topology optimization problem to optimally design a partition layout inside the expansion chamber of a muffler. The lower-limit insertion loss value at a target frequency is constrained, and the partition volume is selected as an object function. In this study, we calculate the insertion loss outside the duct, while to determine the noise-attenuation performance, we use the insertion loss value calculated inside the duct or transmission loss value obtained in a previous study. We employ the finite-element model for acoustical analysis, and we determine the transmission of an incident acoustic wave through each finite element using the functions of design variables that change continuously between "0" and "1." The rigid body elements, which totally reflect incident waves, build up partitions. Finally, we compare optimal topologies that depend on the target frequency and the allowed lower-limit value of insertion loss.