• The Journal of the Acoustical Society of Korea
• /
• v.32 no.6
• /
• pp.509-517
• /
• 2013

In this paper, we researched a method that makes a good acoustic-speech system using a digital signal processing technique with dynamic microphone as a transducer. Good acoustic-speech system should deliver the original sound input to electric signal without distortion. By measuring the frequency response of the microphone, adjustment factors are obtained by comparing measured data and standard frequency response of microphone for each frequency band. The final sound levels are obtained using the developed adjustment factors of frequency responses from the microphone and speaker to match the original sound levels using the digital signal processing technique. Then, we minimize the changes in the frequency response and level due to the variation of the distance from source to microphone, where the frequency responses were measured according to the distance changes.

• The Journal of the Acoustical Society of Korea
• /
• v.30 no.2
• /
• pp.63-72
• /
• 2011

Since the detection probability is critically dependent on the target strength (TS) in active sonar and on the radiated noise level (RNL) in passive sonar, the acoustic materials for echo reduction (ER) and transmission loss (TL) are widely used for the stealth of underwater targets. In this paper, a measurement system based on the small water tank, for the frequency range of greater than 30 kHz, is developed and verified using reference targets. In order to design the water tank and the geometry of test samples, a program is developed to calculate the arrival time of interfering signals due to the reflection from water tank walls and also due to the diffraction from the edge of the test samples. Considering all the interfering signals, an optimal experimental configuration for water tank and test samples is designed and used throughout the experiment. Next, the signal processing algorithms to estimate ER and TL are developed based on the measured propagation loss reflecting the geometric spreading characteristics of the transducer. Finally, a set of reference targets such as aluminium plate and perfectly reflecting plate are used in a small water tank to verify the developed measurement system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.9B
• /
• pp.1551-1562
• /
• 2000

In the using of FBG developed in home land, we designed and manufactured three types of FBG sound transducers the first in Korea. On FBG transducers manufactured we made an demonstrated on respective frequency response peculiarties in the water and analyzed the special characters. As the experimental result on frequency response peculiarities, we made t possible underwater acoustic detection on C type to maximum 18kHz, And for the purpose of realization on multi-point signal detection on wide scope in the water, in the using of WDM(Wavelength Division Multiplexing) method and passive band-pass filter system, established arrays system and succeeded in multi-point underwater acoustic signal detection to the frequency 1.3KHz out of the two B type FBG transducers. Additionally, it would be possible directivity detection for the objects of its source as the intensity of detection signal varies with the sound source's direction and angle. From now on we prepared a new moment on the practical used study on FBG hydrophone.

• Smart Structures and Systems
• /
• v.12 no.2
• /
• pp.97-119
• /
• 2013

This paper presents numerical and experimental results on the use of guided waves for structural health monitoring (SHM) of crack growth during a fatigue test in a thick steel plate used for civil engineering application. Numerical simulation, analytical modeling, and experimental tests are used to prove that piezoelectric wafer active sensor (PWAS) can perform active SHM using guided wave pitch-catch method and passive SHM using acoustic emission (AE). AE simulation was performed with the multi-physic FEM (MP-FEM) approach. The MP-FEM approach permits that the output variables to be expressed directly in electric terms while the two-ways electromechanical conversion is done internally in the MP-FEM formulation. The AE event was simulated as a pulse of defined duration and amplitude. The electrical signal measured at a PWAS receiver was simulated. Experimental tests were performed with PWAS transducers acting as passive receivers of AE signals. An AE source was simulated using 0.5-mm pencil lead breaks. The PWAS transducers were able to pick up AE signal with good strength. Subsequently, PWAS transducers and traditional AE transducer were applied to a 12.7-mm CT specimen subjected to accelerated fatigue testing. Active sensing in pitch catch mode on the CT specimen was applied between the PWAS transducers pairs. Damage indexes were calculated and correlated with actual crack growth. The paper finishes with conclusions and suggestions for further work.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.80-80
• /
• 2000

Surface acoustic wave (SAW) devices have become more important as mobile telecommunication systems need h호-frrequency, low-loss, and down-sized components. Higher-frequency SAW divices can be more sasily realized by developing new h호-SAW-velocity materials. The ZnO/diamond/Si multilasyer structure is one of the most promising material components for GHz-band SAW filters because of its SAW velocity above 10,000 m/sec. Silicon carbide is also a potential candidate material for high frequency, high power and radiation resistive electronic devices due to its superior mechanical, thermal and electronic properties. However, high price of commercialized 6- or 4H-SiC single crystalline wafer is an obstacle to apply SiC to high frequency SAW devices. In this study, single crystalline 3C-SiC thin films were grown on Si (100) by MOCVD using bis-trimethylsilymethane (BTMSM, C7H20Si7) organosilicon precursor. The 3C-SiC film properties were investigated using SEM, TEM, and high resolution XRD. The FWHM of 3C-SiC (200) peak was obtained 0.37 degree. To investigate the SAW propagation characteristics of the 3C-SiC films, SAW filters were fabricated using interdigital transducer electrodes on the top of ZnO/3C-SiC/Si(100), which were used to excite surface acoustic waves. SAW velocities were calculated from the frequency-response measurements of SAW filters. A generalized SAW mode. The hard 3C-SiC thin films stiffened Si substrate so that the velocities of fundamental and the 1st mode increased up to 5,100 m/s and 9,140 m/s, respectively.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.3
• /
• pp.188-194
• /
• 2016

We propose an acousto-optic technique for the nondestructive evaluation of adhesion properties of a Pt/Ti thin-film interface. Since there are some problems encountered when using prevailing techniques to nondestructively evaluate the interfacial properties of micro/nano-scale thin-films, we applied an interferometer that combined the acoustic and optical methods. This technique is based on the Michelson interferometer but the resultant surface of the thin film specimen makes interference instead of the mirror when the interface is excited from the acoustic transducer at the driving frequency. The thin film shows resonance-like behavior at a certain frequency range, resulting in a low-contrast fringe pattern. Therefore, we represented quantitatively the change in fringe pattern as a frequency spectrum and discovered the possibility that the interfacial adhesion properties of a thin film can be evaluated using the newly proposed technique.

• Journal of the Korean institute of surface engineering
• /
• v.42 no.5
• /
• pp.216-219
• /
• 2009

A surface acoustic wave (SAW) filter structure was fabricated employing $4{\mu}m$ thick nanocrystalline diamond (NCD) and $2.2{\mu}m$ thick ZnO films on Si wafer. The NCD film was deposited in an $Ar/CH_4$ gas mixture by microwave plasma chemical vapor deposition method. The ZnO film was formed over the NCD film in an RF magnetron sputter using ZnO target and $Ar/O_2$ gas. On the top of the two layers, copper film was deposited by the RF sputter and inter digital transducer (IDT) electrode pattern (line/space : $1.5/1.5{\mu}m$) was defined by the photolithography including a lift-off etching process. The fabricated SAW filter exhibited the center frequency of 1.66 GHz and the phase velocity of 9,960 m/s, which demonstrated that a giga Hertz SAW filter can be realized by utilizing the nanocrystalline diamond thin film.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.2
• /
• pp.152-159
• /
• 2013

A structural health monitoring(SHM) technique for locating impact position in a composite plate is presented in this paper. The technique employs a single sensor and spatial focusing properties of time reversal(TR) and inverse filtering(IF). We first examine the focusing effect of back-propagated signal at the impact position and its surroundings through simulation. Impact experiments are then carried out and the localization images are found using the TR and IF signal processing, respectively. Both techniques provide accurate impact location results. Compared to existing techniques for locating impact or acoustic emission source, the proposed methods have the benefits of using a single sensor and not requiring knowledge of material properties and geometry of structures. Furthermore, it does not depend on a particular mode of dispersive Lamb waves that is frequently used in the SHM of plate-like structures.

• Proceedings of the Acoustical Society of Korea Conference
• /
• spring
• /
• pp.411-414
• /
• 2000

음의 비선형 전파가 일어나기 쉬운 정도를 나타내는 파라메타로서 기본파 진폭과 제2고조파 진폭의 비로써 매질의 물리적 성질에만 관계하는 파라메타 B/A가 있다(1)(2). 종래 B/A파라메타 측정은 대부분 광대역의 초음파 트랜스듀서 혹은 공진 주파수가 다른 복수의 트랜스듀서를 이용하여 왔다(3). 본 연구에서는 협대역의 단일 트랜스듀서를 이용하여 B/A파라메타를 효율적으로 측정 할 수 있는 전용 초음파 트랜스듀서를 제안하였다. 그 방법으로 특성이 동일한 두 장의 압전체를 적층시키고, 그 중 한 장의 압전체에 전기적인 용량을 접속하여 기본 공진 모드 및 기본 공진 모드의 두 배의 주파수에 해당되는 조화파 모드를 발생시킬 수 있도록 하였다 이것을 시험 제작하여 그 특성을 이론 및 실험적으로 해석한 결과 음향 매질의 비선형 파라메타인 B/A의 측정에 적용 가능함을 확인하였다.

• Korean Journal of Optics and Photonics
• /
• v.17 no.4
• /
• pp.366-370
• /
• 2006

An optical microphone incorporating a reflective diaphragm and a fiber-optic head was demonstrated. The diaphragm was made of a micromirror membrane which is suspended by a silicon bar connected to a frame, allowing fer a displacement induced by acoustic waves. A compact, simple optical head was implemented by exploiting a single multimode fiber. For the assembled microphone, the static characteristics were investigated to find the operation point defined as the optimum distance between the head and the diaphragm, and a flat frequency response with a variation of $\sim$2dB for the range of up to 2 kHz was accomplished.