• Journal of Sensor Science and Technology
• /
• v.18 no.1
• /
• pp.33-41
• /
• 2009

A multilevel acoustic Fresnel lens (MAFL) for the ultrasonic imaging transducer of which center frequency is approximately 5.MHz was newly designed and fabricated. The phase level of the lens was 64, and the focal length and the aperture width were 30.mm and 11.mm, respectively. The characteristics of impulse response, acoustic field and imaging performance of the transducer attached the lens were compared with the transducer attached a conventional refraction type acoustic lens (RAL). The results show that the center frequency, the loop sensitivity, and the focal depth of the MAFL transducer were higher or larger than those of the RAL transducer by approximately 0.2.MHz, 1.4.dB, and 2.mm, respectively. Consequently, it was shown that the brighter acoustic images with higher lateral resolution and the increased imaging performance for deep targets can be obtained by using the MAFL transducer.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.555-556
• /
• 2014

In this paper, topology optimization of two-dimensional acoustic lenses is presented by using the phase field method. The objective of the optimization is to maximize the acoustic pressure at a specified domain inside the acoustic domain for a given frequency, and the constraint is imposed on the amount of the material of the acoustic lens. Topology optimization of two-dimensional acoustic lenses are obtained as the steady state of the phase transition described by the Allen-Cahn equation. The Helmholtz equation modeling the wave propagation is solved by using a finite element method. The effectiveness of the proposed method is verified by applying it for several two-dimensional acoustic lens system design problems.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.6_spc
• /
• pp.687-696
• /
• 2016

A series of process to design an acoustic lens for underwater imaging is reviewed and the method to evaluate characteristics of the lens is investigated. If the target specification of lens is given, the design process consists of the material selection, evaluation of its properties, lens geometry design, prediction of lens characteristics, manufacturing, and evaluation by measurement. In this study, an actual acoustical lens is made by cutting polymethylpentene block. The characteristics of lens are predicted by the hybrid method, combination of ray tracing and Rayleigh integral. For the direct comparison between the prediction and measurement results, a simulation method based on the equivalent source method is suggested to reflect the actual radiation pattern of transducer used for measurements. Finally, the measurement is conducted in a small water tank to observe the actual characteristics of the manufactured lens.

• Proceedings of the KIEE Conference
• /
• 1987.07b
• /
• pp.1591-1594
• /
• 1987

The Scanning Acoustic Microscope(SAM) is an image device which can display the small opaque material or the interior of solid. This paper showed the design of the acoustic lens which is an important factor of the Scanning Acoustic Microscope, and analyzed the performance of the acoustic lens. Finally, I experimented the image processing of the interior of solid through the Scanning Acoustic Microscope and the change of the acoustic image (resolution,contrast) by the change of F/number.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.35 no.2
• /
• pp.134-140
• /
• 2015

Traditional moxibustion therapy can cause severe pain and leave scarring burns at the moxibustion site as it relies on the practitioner's subjective and qualitative treatment. Recently, ultrasound therapy has received attention as an alternative to moxibustion therapy owing to its objectiveness and quantitative nature. However, in order to convert ultrasound energy into heat energy, there is a need to precisely understand the ultrasound-focusing characteristics of the acoustic lens. Therefore, in this study, an FEM simulation was performed for acoustic lenses with different geometries a concave lens and zone lens as the geometry critically influences ultrasound focusing. The acoustic pressure field, amplitude, and focal point were also calculated. Furthermore, the performance of the fabricated acoustic lens was verified by a sound pressure measurement experiment.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39C no.12
• /
• pp.1318-1322
• /
• 2014

We develop new sonar system by way of acoustic focusing which is totally different from conventional one in principle. It focuses input wave on the opposite edge of the lens without aberration perfectly. Then, the motion of acoustic source is read by naked eyes. It can be used as an acoustic window deep underwater by converting sound into light. We introduce the sonar in actual size that can be used underwater and report current situation of the development.

• The Journal of the Acoustical Society of Korea
• /
• v.13 no.5
• /
• pp.15-23
• /
• 1994

We developed an electronic lens for acoustic imaging systems, which is linear array with 31 microphones equally spaced with distance 34mm. Resonant frequency fo receiver circuit coupled to microphone is 20 kHz. We arranged 16 microphones horizontally and 15 microphones vertically, so that the array allows us to obtain a 2 dimensional angle of source, and to track the motion of source in real time. Due to the problem of aliasing in discrete Fourier Transfrom, the maximum observable angle of the lens is limited to 15${\circ}$. We also employed quadrature phase detection scheme to adjust the focus. We have tested the acoustic lens with a personal computer in an anechoic room and obtained the results agreed with the acoustic imaging theory.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.2
• /
• pp.22-28
• /
• 1993

In this paper, the ultrasonic transducer with a spherical liquid lens is designed and an efficient method to calculate the acoustic field radiated from the transducer is presented. A prototype ultrasonic transducer with a spherical liquid lens is constructed and tested. The experimental results are compared with those of the computer simulations and good agreements are achieved. The dynamic control of the geometric focus is obtained by adjusting the radius of curvature of the lens membrane with the volumetric control of the liquid in the lens.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.4
• /
• pp.181-190
• /
• 2014

The underwater acoustic lens system is one of the systems getting high-resolution images on the seafloor by the beam forming method using acoustic lens. The beam forming using acoustic lenses reduces complexity and driving power. When receiving an incoming beam with the acoustic lens array, beam pattern analysis and arrangement problem of the array sensor must be addressed. Introducing SIR (Signal to Interference Ratio), the relationship among sensor interval, beam pattern and image quality would be analyzed. Generally if the sensor interval getting wider, the less effect of the side lobes makes SIR high. If the amplitude of a side lobe is high, SIR is generally getting low. The type of the apodization function changes the width, shape and amplitude of both main lobe and side lobes. Thus an appropriate apodization function can improve SIR. In this paper, SIR is stable at the sensor interval of 13mm with 0-10dB, which is not high relatively. By applying the Chebyshev function, the SIR becomes 80dB over the sensor interval of 37 mm or higher. The Hann and triangular functions demonstrate better SIR when the sensor interval becomes narrower.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.12
• /
• pp.1889-1893
• /
• 1990

In this paper, ultrasonic microscope system has been constructed with the small aperturre acoustic lens and the angle controller, and the new type of B-scanultransonic imaging has been analyzed. The system with small aperture lens was used to detect flaw existing within the thick specimen and its resolution was in the range of one wavelength at interior plane of sample. The anle controller was used to excited surface acoustic wave or shear wave. In order to obtain B-scan image of the flaw existig at interior of solids, shear wave has been excited and backscattering signals from the flaw have been processed. In experimental results, B-scan ultransonic images have been obtain from the flaws of varable shape and measured flaw size from the images has been in good agreement with practical size in the range of 10% error.