• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 춘계학술대회 논문집
• /
• pp.625-629
• /
• 1999

In this study, in order to develop high sensitivity and low noise acoustic emission sensor, we manufactured the Pb(Zr, Ti)O$_3$ ceramics with the addition of WO$_3$ wt% to search for its required characteristics. Dielectric constant was increased as a function of the increase of WO$_3$ wt%. The Pb(Zr, Ti)O$_3$ (EC-65) ceramics added with 0.1lwt% WO$_3$ showed excellent dielectric constant and piezoelectric constants of 1931 and 199.55$\times$10$^{-12}$ (C/N), respectively. Accordingly It was shown as the composition ceramics suitable for AE sensor.

• 한국해양공학회지
• /
• 제11권3호
• /
• pp.29-38
• /
• 1997

Crack penetration behavior by fatigue crack propagation and measurements of AE before-and-after crack penetration were examined using SS41 steel plate. Experimental crack shape of SU type was in good agreement with calculated shape rather than S type. Crack propagation behavior on the front surface appears not to change markedly after penetration. However, crack growth on the back surface appears to accelerate as reported by author. As a crack propagates, AE occurred heavily just before penetration. Then, it decreases and crack is penetrating. A transition from plane strain to plane stress was observed by fractographic study. At this time, separation of fracture surface was shown which affects AE occurrence.

• 한국산업융합학회 논문집
• /
• 제4권2호
• /
• pp.127-132
• /
• 2001

In turning, the chip may be produced in the form of continuous chip or discontinuous chip. The continuous chips are dangerous to the operator and difficult to be handled at high speed machining. The signal of AE(Acoustic Emission) is found out to be related to cutting conditions, tool materials, test conditions and tool geometry in turning. In this study, the relationship between AE signal and chip form was experimentally investigated. The experimental results show that the types of chip form are possible to be classified from the AE signal using fuzzy logic.

• 한국정밀공학회지
• /
• 제12권3호
• /
• pp.130-143
• /
• 1995

This paper presents a new methodology for on-line tool breadage detection by sensor fusion of an acoustic emission (AE) sensor and a built-in force sensor. A built-in piezoelectric force sensor, instead of a tool dynamometer, was used to measure the cutting force without altering the machine tool dynamics. The sensor was inserted in the tool turret housing of an NC lathe. FEM analysis was carried out to locate the most sensitive position for the sensor. A burst of AE signal was used as a triggering signal to inspect the cutting force. A sighificant drop of cutting force was utilized to detect tool breakage. The algorithm was implemented on a DSP board for in-process tool breakage detection. Experiental works showed an excellent monitoring capability of the proposed tool breakage detection system.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2002년도 춘계학술대회 논문집
• /
• pp.134-139
• /
• 2002

Fracture behaviors of pipes with local wall thinning are very important for the integrity of nuclear power plant. However, effects of local wall thinning on strength and fracture behaviors of piping system were not well studied. Acoustic emission(AE) has been widely used in various fields because of its extreme sensitivity, dynamic detection ability and location of growing defects. In this study, we investigated failure modes of locally wall thinned pipes and AE signals by bending test. From test results, we could be divided four types of failure modes of ovalization, crack initiation after ovalization, local buckling and crack initiation after local buckling. And fracture behaviors such as elastic region, yielding range, plastic deformation range and crack progress could be evaluated by AE counts, accumulative counts and time-frequency analysis during bending test. It is expected to be basic data that can protect a risk according to local wall thinning of pipes, as a real time test of AE.

• 지질공학
• /
• 제28권3호
• /
• pp.349-365
• /
• 2018

The strain and acoustic emission (AE) signals of Pocheon granite were measured during uniaxial compression tests to investigate microcrack formation and damage. Crack closure, initiation, and damage stresses of each sample were determined through an analysis of the crack volumetric strain and stiffness. The samples experienced four damage stages according to stress levels: stage 1 = crack closure stage; stage 2 = elastic stage; stage 3 = crack initiation stage; stage 4 = crack damage stage. At least 75% of all AE signals occurred in stages 3 and 4, and different AE parameters were detected in the four stress stages. Rise time, count, energy, and duration clearly showed a tendency to gradually increase with the damage stress stage. In particular, the rise time, energy, and duration increased by at least 95% in stage 4 as compared with stage 1. However, the maximum amplitude showed a smaller increase, and the average frequency decreased slightly at higher stages. These results indicate that as the degree of rock damage increases, the crack size grows larger. The crack types corresponding to the AE signals were determined using the relationship between RA (Rise time / Amplitude) values and average frequencies. Tension cracking was dominant in all stress stages. Shear cracking was rare in stages 1 and 2, but increased in stages 3 and 4. These results are consistent with previous studies that reported cracking begins after samples have already been damaged. Our study shows that the state of rock damage can be investigated solely through an analysis of AE parameters when rocks are under compressive stress. As such, this methodology is suitable for understanding and monitoring the stress state of bedrock.

• Journal of Advanced Marine Engineering and Technology
• /
• 제17권4호
• /
• pp.38-48
• /
• 1993

A study on friction welding of stainless steel bar(SUS431) to chrome molybdenum steel bar(SCM21) was accomplished experimentally through analysis for relations among friction welding conditions, tension test, hardness test, microstructure test and acoustic emission test. The results obtained are summarized as follows ; 1. Through friction welding of SUS431 bar to SCM21 bar, the optimum welding condition by considering on strength and toughness was found to be the range of heating time of 3-5 sec when the number of rotating speed of 2000rpm, heating pressure of 10kg/$mm^2$, and upsetting time of 4 sec. 2. Quantitative ralationship was identified between heating time($T_1$, sec) and tensile strength (${\sigma},\;kgf/mm^2$) of the friction welded joint and the relation equation is $\sigma$=52.62$T_1{^{0.06}}$. 3. Through AE test, quantitative relationship was confirmed between heating time($T_1$, sec) and total AE(N, counts) during welding, and the relation is computed as follows ; N=30413.6$e^{0.06T1}$. 4. It was confirmed that the quantitative ralationship exists between the tensile strength of the welded joints and AE cumulative counts. And the relation is computed as the following ; ${\sigma}$=16.37(ln N)- 116.4. 5. When ONZ=36500-41500 counts by $OT_1Z$=3~5sec, it was identified by experiment that the range of welded joint tensile strength is 55.6-57.7kgf/$mm^2$/ whose joint efficiency is more than 100%, and it was experimentally confirmed that the real-time nondestructive quality(strength) evaluation for the friction welded joints could be possible by acoustic emission technique.

• 비파괴검사학회지
• /
• 제21권3호
• /
• pp.251-260
• /
• 2001

단조인장시험하에서 CFRP적층재의 손상과정을 음향방출과 초음파시험에 의해 평가하였다. 시험편으로부터의 음항방출신호의 진폭 분포는 기지재 균열(matrix crack), 박리(debonding), 섬유 pull-out 및 섬유 과단(fiber fracture)과 같은 CFRP에서의 파괴기구를 분석하는데 도움을 주며, 초음파 진폭감쇠의 특성 또한 각각의 파괴기구를 분석하는데 유용하다. 여러종류의 CFRP시험편을 사용하여 음향방출신호와 초음파신호의 진폭감쇠를 조사하였다. 끝으로 하중 제하중(loading-unloading) 시험이 초음파내의 진폭비에 대한 Felicity effect와 감쇠를 조사하기 위해서 수행되었다. 전 실험에 걸쳐 초음파신호의 진폭감쇠와 음향방출 파라미터(parameter)들은 동시에 검출되었다. 이로써 음향방출과 초음파시험의 두 파라미터들이 CERP에서의 파괴기구를 분석하기 위해 효과적으로 사용될 수 있음이 확인되었다.

• 한국해양공학회지
• /
• 제26권5호
• /
• pp.5-10
• /
• 2012

In this study, carbon steel (A53) is used as the material for the pipes in a marine plant and ship industry. Welds are necessary to join the carbon steel, and the effect of this welding on the properties of the carbon steel has been studied by many researchers. In this study, the dynamic behavior of welded carbon steel was studied using an acoustic emission (AE) technique, which is a nondestructive test. There are numerous AE parameters that can be used to analyze the damage behavior of carbon steel by external loading. The AE parameters of energy, cumulative count, amplitude, and AE event were used, and each parameter was differentiated according to the degree of damage to the carbon steel. The energy showed a high level at the elastic range of the load curve, while the amplitude had the highest value at the hardening region. The cumulative count showed a growth tendency similar to the loading curve. In addition, an ultrasonic technique and hardness test were applied to evaluate the mechanical properties according to the base zone, HAZ region, and weld zone of the weld specimen. The velocity and attenuation ratio showed little change between zones, and an evaluation of the ultrasonic waves on each zone of the specimen was found to be a useful method to clarify the mechanical properties of the carbon steel.

• 대한토목학회논문집
• /
• 제33권2호
• /
• pp.433-442
• /
• 2013

이 논문에는 길이가 50m인 프리스트레스트 콘크리트 박스거더를 이용한 1차원, 2차원 음원위치 산정을 위한 실험연구 내용을 수록하였다. 슈미트 햄머를 이용하여 콘크리트 표면에 타격하여 충격음파를 발생시켰으며 PSC박스거더 복부판에 평균 9.34m 간격으로 부착한 AE센서를 통해 충격 음파를 감지하였다. 공용중인 PSC박스거더 교량에 발생할 수 있는 잡음을 고려하여 음파의 도달시간을 음파의 세기가 0Volt, 0.5Volt, 그리고 1.0Volt일 때를 기준으로 산정하였다. 음파의 도달시간들에 대한 측정결과를 토대로 충격음파의 음원위치를 최소제곱법을 이용해 산정하였다. 실험결과를 토대로 2차원 음원위치 산정시 오차를 최소화하기 위해 필요한 음향센서 간격과 음향센서의 네트워크에 대해 고찰하였다.