• Journal of the Semiconductor & Display Technology
• /
• v.18 no.1
• /
• pp.25-31
• /
• 2019

In this study, a new adhesion evaluating equipment and data processing methods were developed to overcome some limitations of existing evaluating equipment. Nano-diamond coated tool is a specimen of experiment. When applying frictional force and shear force on the specimen by a rotating polishing pad, delamination occurs at a moment. During each experiment, the vibration, load, and torque is obtained by accelerometer, loadcell and torque s+ kpensor. Frictional force and coefficient of friction are obtained by calculating torque and load. Based on FFT transformation, acceleration is processed and analyzed. As a result, the moment of delamination and the load at that time can be detected by the new developed equipment and measurement system. Finally, we call this load as an Adhesion force.

• Journal of Auto-vehicle Safety Association
• /
• v.14 no.4
• /
• pp.16-20
• /
• 2022

Accurate state estimation is important for autonomous driving. However, the estimation error increases in situations that a lot of longitudinal slip occurs. Therefore, this paper presents a vehicle state estimation method using an Extended Kalman Filter. The filter estimates the states of the host vehicle robust to wheel slip. It utilizes the measurements of the four-wheel rotational speeds, longitudinal acceleration, yaw-rate, and steering wheel angle. Nonlinear measurement model is represented by Ackermann Model. The main advantage of this approach is the accurate estimation of yaw rate due to the measurement of the steering wheel angle. The proposed algorithm is verified in scenarios of autonomous emergency braking (AEB), lane change (LC), lane keeping (LK) using an automated vehicle. The results show that the proposed algorithm guarantees accurate estimation in such scenarios.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.3
• /
• pp.56-62
• /
• 1996

This paper presented a new measuring system to improve circular motion accuracy by using two-dimensonal probe and master ring for NC machine tools. This measuring system reduced the circular motion error conspicuously by eliminating the influence of the acceleration/deceleration range and compensating the friction force whose influences were significant while measuring the motion. Experimental results show that this system had enough accuracy to measure a circular motion for NC machine tools, compared with the circular test method and the r .theta. method.

• Journal of Wind Energy
• /
• v.14 no.3
• /
• pp.91-99
• /
• 2023

In research conducted on a southwestern Korean offshore meteorological tower, acceleration datasets were gathered over half a year with time-history sensors. To enhance data credibility, a parallel measurement system was used for verification. A model of the tower was configured using beam elements, and with modifications accounting for added stiffness from auxiliary structures. Ground interactions were considered as calibrated springs based on soil layer properties. The tower's dynamic attributes and mass sensitivity were discerned using eigenvalue analysis. The structural natural frequency was consistent, with variations primarily due to new equipment adding approximately 1400 kgs. With free vibration damping assumptions, a damping ratio of roughly 1 % was derived.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.1
• /
• pp.47-54
• /
• 2014

Endurance of ship hull can be estimated by existing regulations and fatigue estimation methods. These can be applied to the hull materials that are recommended by ship regulations but can't be applied to new materials. In this study, structural force in the worst sailing condition is obtained by the acceleration measurement test of small polyethylene boat and the endurance of small polyethylene hull is estimated by rainflow cycle counting method and linear cumulative damage rule. Maximum Von-Mises stress on the polyethylene boat is 1.8MPa and much lower than the fatigue strength of at least 5.9MPa for the fatigue life of $1{\times}10^9$ cycles. Fatigue life of the polyethylene boat hull is estimated to be 6,229 years.

• Journal of the Korea Computer Graphics Society
• /
• v.19 no.4
• /
• pp.13-22
• /
• 2013

A motion capture system is widely used in movies, computer game, and computer animation industries because it allows for creating realistic human motions efficiently. The inertial motion capture system has several advantages over more popular vision-based systems in terms of the required space and cost. However, it suffers from low accuracy due to the relatively high noise levels of the inertial sensors. In particular, the accelerometer used for measuring gravity direction loses the accuracy when the sensor is moving with non-zero linear acceleration. In this paper, we propose a method to remove the linear acceleration component from the accelerometer data in order to improve the accuracy of measuring gravity direction. In addition, we develop a simple method to calibrate the joint axis of a link to which an inertial sensor belongs as well as the position of a sensor with respect to the link. The calibration enables attaching inertial sensors in an arbitrary position and orientation with respect to a link.

• Journal of the Korea Convergence Society
• /
• v.11 no.10
• /
• pp.355-361
• /
• 2020

The squat is an exercise that can effectively improve the muscle strength of the lower body, which can be performed in a variety of places without restrictions on places including homes. However, injuries due to incorrect motion or excessive angles are frequently occurring. In this study, we developed a single sensor-based squat angle measurement system that can inform the squat angle according to the correct motion during the squat exercise. The sensor module, including the acceleration sensor and the gyro sensor, is attached to the user's thigh. The squat angle was calculated using the complementary filter complementing the pros and cons of acceleration and gyro sensor. It was found that the calculated squat angle showed the proper correlation compared to the squat angle measured by a goniometer, and the influence of the coefficient of the complementary filter on the accuracy was evaluated.

• Journal of the Ergonomics Society of Korea
• /
• v.35 no.5
• /
• pp.319-341
• /
• 2016

Objective:This research analyzed the lower-limb motion in kinetic and kinematic way while walking on various terrains to develop Foot-Ground Contact Detection (FGCD) algorithm using the Inertial Measurement Unit (IMU). Background: To estimate the location of human in GPS-denied environments, it is well known that the lower-limb kinematics based on IMU sensors, and pressure insoles are very useful. IMU is mainly used to solve the lower-limb kinematics, and pressure insole are mainly used to detect the foot-ground contacts in stance phase. However, the use of multiple sensors are not desirable in most cases. Therefore, only IMU based FGCD can be an efficient method. Method: Orientation and acceleration of lower-limb of 10 participants were measured using IMU while walking on flat ground, ascending and descending slope and stairs. And the inertial information showing significant changes at the Heel strike (HS), Full contact (FC), Heel off (HO) and Toe off (TO) was analyzed. Results: The results confirm that pitch angle, rate of pitch angle of foot and shank, and acceleration in x, z directions of the foot are useful in detecting the four different contacts in five different walking terrain. Conclusion: IMU based FGCD Algorithm considering all walking terrain possible in daily life was successfully developed based on all IMU output signals showing significant changes at the four steps of stance phase. Application: The information of the contact between foot and ground can be used for solving lower-limb kinematics to estimating an individual's location and walking speed.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.10
• /
• pp.941-946
• /
• 2013

In this paper, an enhanced method for attitude determination is proposed for systems using an IMU (Inertial Measurement Unit). In attitude determination with IMU, it is generally assumed that the IMU can be located in the center of gravity on the vehicle. If the IMU is not located in the center of gravity, the accelerometers of the IMU are disturbed from additive accelerations such as centripetal acceleration and tangential acceleration. Additive accelerations are derived from the lever arm which is the distance between the center of gravity and the position of the IMU. The performance of estimation errors can be maintained in system with a non-zero lever arm, if the lever arm is estimated to remove the additive accelerations from the accelerometer's measurements. In this paper, an estimation using Kalman filter is proposed to include the lever arm in the state variables of the state space equation. For the Kalman filter, the process model and the measurement model for attitude determination are made up by using quaternion. In order to evaluate the proposed algorithm, both of the simulations and the experiments are performed for the simplified scenario of motion.

• Journal of Korean Society of Steel Construction
• /
• v.15 no.2
• /
• pp.117-124
• /
• 2003

Wind-induced motions, like acceleration for instance, often influence designs for high-rise buildings. As a consequence, correct assessment of natural frequency becomes important. The empirical expressions used to quantify this parameter at the design phase tend to yield values that are significantly different from each other. This paper is concerned with the natural periods of steel buildings. It describes the vibration measurement methods that were employed for testing buildings. This paper will also present reliable methods of assessing the natural period from ambient vibration tests. Data from measurements on 21 buildings in Seoul were provided while 21 buildings were tested by ambient vibration measurements to obtain the natural periods. While regression formulas of natural periods for steel-frarried tall buildings were suggested,the obtained formula was compared with the empirical expressions of structural standards and the Eigen-value analysis.