• 대한인간공학회지
• /
• 제17권2호
• /
• pp.11-23
• /
• 1998

Dynamic motion difference between normal subjects and low-back pain (LBP) patients has been investigated in terms of kinematic variables such as range of motion, velocity and acceleration of the back and hip. Ten healthy subjects and ten LBP patients were recruited in this study. Electro-goniometer such as Lumbar Motion Monitor and Hip Monitor have been used for quantitative measurement of the trunk motion during repetitive flexion and extension for ten seconds. Results indicated that the velocity and acceleration of the back and hip were important parameters to quantitatively identify LBP patients. The consistency of cyclic trunk motion and the relationship between the back and hip were measured in terms of Variance Ratio and Phase Angle in order to accurately assess the motion characteristics of LBP patients. In particular, the hip motion has been proven to be a very important factor in describing the kinematics of damaged lower back. The functional evaluation technique suggested in this study will be a tool to assist physicians for an accurate diagnosis and timely rehabilitation along with current image diagnosis techniques.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.299-300
• /
• 2007

In this paper, slip wear phenomenon of train was studied by traction force of acceleration and braking force of deceleration. First, the slip wear phenomenon on train operation mode was analyzed when powering, coasting and braking each and then rail wear was analyzed from the slip wear data. Especially, the data proved correlation between slip wear and deceleration rather than acceleration. Second, If velocity of a train is constant, even though the velocity is high, ATO logging data and measurement data proved that the rail wear is not serious. It will help for efficient braking force operation providing fundamental data to braking step control.

• Journal of Electrical Engineering and Technology
• /
• 제7권1호
• /
• pp.103-108
• /
• 2012

The present study describes the considerations on the long-term reliability of the on-line partial discharge (PD) ceramic sensor for thermal power generators. Voltage acceleration aging tests were carried out under continuous and impulsive thermal aging at more than $100^{\circ}C$, considering the practical service environment. Experimental results show that the sensors have a life that could last for more than 100 years, excellent dielectric characteristics, and insulation strength. In addition, the ceramic on-line PD sensors were installed in a thermal power generator in Korea for demonstration. The results of the PD calibration and test voltage application prove that the on-line ceramic sensors have satisfactory performances for on-line PD measurement.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제50권1호
• /
• pp.31-37
• /
• 2001

A robust adaptive technique for the longitudinal control of a platoon of automated vehicles is presented. A nonlinear model is used to represent the dynamics of each vehicle within the platoon. The external disturbances such as wind gust and a disturbance term due to engine transmission variations and so on are considered. The state observer is used to avoid direct measurement of the relative velocity or acceleration between the controlled and leading vehicles or the controlled vehicles's acceleration. The proposed controller guarantees to recover platoon stability in operation even if a speed dependent spacing policy is adopted, which incorporates a constant time headway in addition to the constant distance. It is shown that the proposed observer is exponentially stable, and the at the robust adaptive controller is stable. The simulation results demonstrate excellent tracking even in the presence of disturbances.

• International Journal of Automotive Technology
• /
• 제7권3호
• /
• pp.269-276
• /
• 2006

Running tests on roads were conducted to clarify the influences of road infrastructure, traffic condition and vehicle's emission level to the amount of emission at local roadsides, and to reveal the operation patterns which can reduce the emission peaks. NOx emission peaks of two light duty freight diesel vehicles which have different emission levels were evaluated by using an on-board measurement system. Tests were carried out with various payload conditions and road conditions. As a result many NOx emission peaks were observed when the vehicles were starting or accelerating at intersections. The test vehicle which has higher emission level caused higher frequency and level of NOx emission peaks. Shifting up at lower engine speed in combination with lower acceleration brought out not only reduction of NOx emission peaks level but also of $CO_2$ mass emission.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.840-845
• /
• 2004

Development of the linear motors is recently required to control a high-speed and high-resolution in the high-integrated and speed process industry. This paper presents vibration analyses as well as measurement standards of the newly developed linear motors through analyzing the vibration characteristics of the advanced products. Vibration experiments are conducted for identifying vibration level during operation. They are also included in the modal test to analyze dynamic characteristics. Analytic data using Finite Element Method (FEM) are compared with the results of the modal. The FEM and experiments make it possible to understand these characteristics. Further, through computer simulation for the behavior of moving part to be vibration source, the best acceleration pattern of moving part movement can be verified to achieve effective moving part positioning and reduce the vibration due to moving part movement.

• International Journal of Automotive Technology
• /
• 제8권4호
• /
• pp.521-531
• /
• 2007

Measurement of the vibration transmitted through rotating shafts such as half shafts in vehicles is of interest in applications such as noise transfer analysis and the study of operating deflections. Vibration signals transmitted through a rotating shaft usually include six degree-of-freedom components, thus making the measurement of vibration a challenging task. In the present work, a new measurement method is presented, one that resolves the minimum of only two one-axis accelerometer signals into all components of vibration with reasonable accuracy. The method utilizes the Dopplerized signals obtained from accelerometers attached to a rotating shaft and a Void-Kalman order tracking filter to decompose signals into orders of different vibration components. The new method proposed in the present work is verified by simulated run-up test data and applied to an experimentally obtained data set.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.1380-1383
• /
• 1996

This paper presents a recoil and counter recoil(R&CR) motion measurement method using linear variable differential transformers(LVDT). The output of a LVDT is obtained from the differential voltage of the 2nd transformers. As a sensor core is attached at the motion body, the output is directly proportional to the core motion. Displacement, velocity and acceleration are measure from the core length. With a comparison between the measurement result and the known value which is obtained by the precision steel tape, the accuracy and the usefulness of the proposed scheme is validated.

• 소음진동
• /
• 제6권6호
• /
• pp.727-733
• /
• 1996

Machines installed in various structures emit airborne sound and structureborne sound and are major source of noise and vibration. Especially when machines are installed upon a flexible foundation, most of noise and vibration are due to transmission of structureborne sound. Therefore, characterization and measurement of structureborne sound source level are necessary for controlling noise and vibration. But structureborne sound from vibrating machine is strongly coupled to the supportingstructure. This paper proposes the method of estimating the supporting sturcture's dynamic character- istic and structureborne sound source level for machine installed system without separating the machine, resilient mount and foundation.

• International Journal of Safety
• /
• 제7권1호
• /
• pp.26-29
• /
• 2008

The purpose of this study is the measurement of whole-body vibration for different road surfaces. Experimental measurements were taken on asphalt, cement, and off-road surfaces as defined by ISO 2631-1. Each experiment was conducted under the same set of conditions (measurement duration, times, speed, vehicle type). Measurement duration was 10 minutes and 3 separate measurements were taken on each road surface. Vehicle speed was 60km/h. In accordance with ISO 2631-1, an acceleration sensor is set up between the driver's seat and the human body. For evaluation, RMS(root-mean-square) values were taken as suggested by ISO 2631-1. The results suggest "health guidance caution zones", and the evaluation was based on obtaining the vector sum with "health guidance caution zones".