• Elastomers and Composites
• /
• 제58권3호
• /
• pp.103-111
• /
• 2023

The abrasion resistances of silica-filled styrene-butadiene rubber (SBR) compounds prepared with and without dicyclopentadiene resin (SBR-R and SBR-0, respectively) were studied using four different abrasion testers, namely cut and chip (CC), Lambourn, DIN, and laboratory abrasion tester (LAT100). The effect of the resin on the abrasion behavior was elucidated by analyzing the morphologies and size distributions of wear particles. All the wear particles had rough surfaces, but those obtained in the Lambourn abrasion test exhibited relatively smooth surfaces. The size distributions of the wear particles showed different trends depending on the abrasion tester and the rubber compound; however, most of the wear particles were larger than 1000 ㎛. The SBR-R sample showed a wide range of particle sizes (from 63 ㎛) in the LAT100 abrasion test and majority of the wear particles were 500-1000 ㎛, whereas the SBR-0 sample had the most distribution of larger than 1000 ㎛. The abrasion rates of SBR-0 sample were lower than those of the SBR-R sample for the CC and LAT100 abrasion tests, but the Lambourn abrasion test result showed the opposite trend. Addition of the resin influenced the abrasion behavior, however the effect varied depending on the type of abrasion tests.

• Fibers and Polymers
• /
• 제4권4호
• /
• pp.151-155
• /
• 2003

The abrasion behavior of three kinds of warp knitted fabrics, which are normally used for upper sole of footwear, was evaluated. We measured the changes of mechanical and structural properties of each sample as abrasion cycle increased. Each sample showed similar trends in compression and surface properties but there were significant differences in abrasion rate among the samples. The mechanical properties showed remarkable differences with directions. The frictional coefficient (MIU) of fabric surface increased at the beginning of abrasion and decreased as abrasion cycles increased. The weight and thickness of the fabric linearly decreased with abrasion cycles. The surface roughness (SMD) and the compressional resilience (RC) decreased as abrasion cycles increased while compressional energy (WC) increased.

• Elastomers and Composites
• /
• 제58권1호
• /
• pp.17-25
• /
• 2023

Abrasion tests of model tire tread compounds (NR and NR/BR blend compounds) were performed at different slip angles (1° and 7°) using a laboratory abrasion tester. The abrasion behavior was investigated by analyzing the worn surface and wear particles. The abrasion spacing formed on the specimen worn at the large slip angle of 7° was significantly narrower than that at the small slip angle of 1°, while the abrasion depth for the specimen worn at 7° was lower than that at 1°. The abrasion spacing and depth tended to be narrower and lower, respectively, as the BR content increased. The abrasion patterns were clearly visible on the outside of the specimen for the slip angle of 1° but not for 7°. The wear particles had a rough surface and there were numerous micro-bumps. It was found that the crosslink density affected the abrasion patterns and morphologies of the wear particles.

• 한국재료학회지
• /
• 제13권12호
• /
• pp.850-854
• /
• 2003

The abrasion wear behavior on the hardfacing weld was investigated by performing abrasion wear, hardness, and microstructural tests. The gas metal arc(GMA) weld was produced by using the cored wire which was filled with the hard metal, i.e., the recycled tungsten carbide (WC) reinforced metal matrix composite. For 30% addition of the hard metal, the abrasion wear resistance was significantly improved comparing with that for 20% addition of the hard metal. Above 30% addition of the hard metal, however, there was no significant improvement of the wear resistance. The improvement of the wear resistance was due to the increased amount of eutectic carbides(W$_{6}$C) which was formed during GMA welding. For the weld in which the hard metal was added to 30-40%, an optimum level of abrasion wear resistance was performed.

• Corrosion Science and Technology
• /
• 제7권6호
• /
• pp.362-369
• /
• 2008

The impact abrasion behavior of high manganese steel is investigated under three kinds of impact energy in acid hematite ore slurry by using a modified MLD-10 impact abrasion tester. Through the SEM observation of the worn surface and the optical metallographic analysis of the cross-sectional samples, the corrosive impact abrasion mechanisms of the steel under different impact energies are studied. In acid-hematite slurry, the variations of impact energies would result in synchronous transformation of the impact abrasion properties and mechanisms of the high manganese steel in the corrosive condition, as led different corrosive impact abrasion mechanism under different impact energies.

• 폴리머
• /
• 제35권1호
• /
• pp.30-34
• /
• 2011

나일론 12의 열적 거동 및 내마모 특성을 확인하기 위해서 100~600 kGy로 조사선량을 달리 하여 전자선가교 반응을 진행하였다. 가교효과를 증대시키기 위해서 TAC, TAIC, TMPTMA의 가교제를 추가로 사용하였다. 나일론 12는 200 kGy 이상 전자선 가교가 진행되어야 높은 젤화율을 보이며, 조사선량이 증가할수록 결정성이 낮아져 $T_m$과 DSC 피크 면적이 서서히 감소되는 것을 확인하였고, 또한 열분해 온도가 상승하여 열적 안정성이 우수해짐을 확인하였다. 그리고 나일론 12의 내마모 특성도 향상되어 가교 전과 비교하였을 때 마모량, 마모계수가 감소하는 경향을 나타내었고, 마모 표변을 SEM 분석을 통해서 확인하였다. 나일론 12에 첨가된 가교제는 전자선 가교시 우수한 가교 효과를 나타내며, 열적, 내마모 특성을 향상시키는 것으로 확인되었다.

• 대한조선학회논문집
• /
• 제57권6호
• /
• pp.365-372
• /
• 2020

Ice induced abrasion is known as a critical problem in concrete gravity based offshore structures, which are mainly used in the arctic regions. Although many researches on ice abrasion have been conducted for the last several decades, there still are some difficulties in designing concrete gravity based offshore structures against abrasion problem because there is no standardized method yet due to the uncertain physics involved in. This paper presents an experimental study for the evaluation of concrete abrasion characteristics due to ice friction on concrete surface. For the test, a testing machine capable of abrasion and friction was designed and produced, and standardized procedure was proposed to produce ice specimen used for abrasion test. For the experiment, compressive strength of the ice specimen were explored through a static compression test. Then the friction test between ice specimen and concrete surface was performed and friction coefficients were derived using measured vertical and horizontal forces. Dependency of friction coefficients on some test parameters were studied and discussed as well.

• Elastomers and Composites
• /
• 제46권1호
• /
• pp.70-77
• /
• 2011

슬러리와 접하는 환경에서 사용되는 고무 소재의 슬러리 마모 거동을 평가하기 위해 새로운 형태의 슬러리 마모시험기(Slurry Wear Tester; SWT)가 본 연구에서 제안되었다. 슬러리 마모 거동을 평가하기 위한 기본 매트릭스로 천연고무(NR)와 클로로프렌고무(CR)가 선정되었다. SWT 장치의 챔버를 채우기 위한 유체로는 35% HCl 용액과 NaCl 용액이 사용되었다. SWT의 결과는 기존의 고무 마모시험 방법들중의 하나인 건식 상태에서 시험이 진행되는 Akron 마모시험의 결과와 비교를 하였다. Akron 마모 시험의 결과에 따르면 CR이 NR 보다 더 빠른 속도로 마모가 됨을 알 수 있었으며 재료의 히스테레시스 특성이 마모에 영향을 미침을 알 수 있었다. 그러나 SWT 결과에 따르면 CR과 NR의 슬러리 마모거동은 큰 차이가 없었으며 더구나 산의 농도와 HCl 용액과 NaCl 용액에 침지된 시간에 따라서도 슬러리 마모속도에는 큰 영향이 없었다. 이는 슬러리에 포함된 유체가 마모지와 시편 사이의 마찰을 감소시켰기 때문이라고 사료되었다. 또한 Akron 마모 시험의 경우 고무 소재의 히스테레시스가 마모에 영향을 미쳤지만, SWT의 경우 유체는 반복 변형에 의해 발생되는 열을 감소시키고 마모지 표면에 남아있는 마모 찌꺼기들을 제거하였기 때문에 Akron 마모 시험의 결과와는 다른 결과를 나타내었다. 따라서 슬러리에 의한 고무 소재의 마모를 평가하는데 있어서 기존의 방식인 건식방법으로 마모 거동을 평가할 경우 잘못된 결과를 초래할 수 있음을 알 수 있었다.

• Tribology and Lubricants
• /
• 제11권3호
• /
• pp.11-23
• /
• 1995

The friction and wear behavior of $Al_{2}O_{3}$, SiC, and $Si_{3}N_{4}$ under the different sliding conditions were investigated. The cylinder-on-disc wear tester was used for a wear test method. Using the servo-motor, the sliding speed did not alternate due to the frictional forces. Three kinds of loads were selected to watch the variation of the wear rates and the frictional forces under a constant speed. Three kinds of sliding conditions were used to see the effects of the oxidation and the abrasion. The dominant wear mechanisms of $Al_{2}O_{3}$ were the abrasion and the formation of transfer layers. The abrasion has a great effect on the wear of SiC. The wear of $Si_{3}N_{4}$ was due to the asperity-failure and the oxidation. Also, the wear rate of each ceramic is shown to be related to the frictional power provided to the tribological system.

• 대한치과보철학회지
• /
• 제41권6호
• /
• pp.747-761
• /
• 2003

Statement of problem. The proper materials of attachments for implant retained overdenture are unknown, such as the correlation between retention and abrasion, as well as the types of materials that are suitable for patrix and for matrix individually. Purpose of this study. The aim of this study was to select a proper clinical attachment system for a successful treatment as well as patient satisfaction. Methods. Retention and abrasion of 14 commercial attachments were measured during 15,000 removes. Results. A retentive part (matrix) which requires elasticity has to be made of gold while the patrix part which does not require elasticity has to be made of titanium. This gold matrix / titanium patrix combination showed the most retentive force and the least retention loss.