• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.1267-1271
• /
• 2009

In the present study, performance characteristics on environment change of A/C applied fin-tube and PF heat exchangers were experimentally investigated. Capacity and COP changing an outlet air velocity, an indoor/outdoor temperature and a relative humidity were obtained. Air－enthalpy calorimeter was used. As the air velocity, indoor temperature and relative humidity increase, capacity and COP increase. PF A/C has smaller refrigerant weight than the fin-tube A/C. The performance of PF-2 A/C with the squarer fin was more excellent than that of PF-1 A/C with the triangler fin.

• Journal of Sensor Science and Technology
• /
• v.17 no.6
• /
• pp.414-417
• /
• 2008

This paper describes the fabrication of a Pd/poly 3C-SiC Schottky diode and its characteristics, in which the poly 3C-SiC layer and Pd Schottky contact were deposited by using APCVD and sputter, respectively. Crystalline quality, uniformity, and preferred orientations of the Pd thin film were evaluated by SEM and XRD, respectively. Pd/poly 3C-SiC schottky diodes were fabricated and characterized by I-V and C-V measurements. Its electric current density Js and barrier height voltage were measured as $2{\times}10^{-3}A/cm^2$ and 0.58 eV, respectively. These devices were operated until about $400^{\circ}C$. Therefore, from these results, Pd/poly 3C-SiC Schottky devices have very high potential for high temperature chemical sensor applications.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1991.10a
• /
• pp.7-9
• /
• 1991

$\prod$-A characteristics of N-docosylquinolium-TCNQ complex were investigated with the following variations. I> $\prod$-A characteristics with a variation of spreading amount. ii> $\prod$-A characteristics with a variation of barrier speed. iii> $\prod$-A characteristics with a variation of subphase temperature. An optimum surface pressure for a deposition of Langmuir-Blodgett(LB) layer was found to be a 40∼50 mN/m in pure water subphase (pH 5.4, $25^{\circ}C$).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.6
• /
• pp.1390-1395
• /
• 2006

In this paper, we propose an optical add-drop multiplexer(OADM) for dense-WDM (DWDM) which consists of the fiber Bragg grating(FBG) filter and investigate the temperature characteristics of it. To resolve the characteristics, we find and analyze numerically its temperature response, and fabricate an OADM and measure its output spectrum. From the obtained results, we khow that the center wavelength of output spectrum shifts approximately 0.01230$nm/^{\circ}C$ within a temperature range $-30^{\circ}C{\sim}90^{\circ}C$.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.10
• /
• pp.425-430
• /
• 2003

A CMOS Voltage-Controlled Oscillator(VCO) for application at temperature stable system is designed. The VCO consists of bandgap voltage reference circuit, comparator, and voltage-to-current converter and the VCO has a temperature stable characteristics. The difference between simulated and calculated values is less than about 5% in output characteristics when the input voltage range is from 1V to 3.25V. The CMOS VCO has error less than about $\pm$0.85% in the temperature range from $-25^{\circ}C$ to $75^{\circ}C$.

• Transactions on Electrical and Electronic Materials
• /
• v.1 no.2
• /
• pp.28-31
• /
• 2000

BaTiO$_3$cerameic thin films doped with Mn were manufactured by rf/dc magnetron sputter technique. We have investigated crystal structure, surface morphology and PRCR(positive-temperature coefficient of resistance) characteristics of the specimen depending on second heat-treatment temperature. Second heat treatment of the specimen were performed in the temperature range of 400 to 1350$\^{C}$ X-ray diffraction patterns of BaTiO$_3$ thin films show that the specimen heat treated below 600$\^{C}$ is an amorphous phase and the one heat treated above 1100$\^{C}$ forms a poly-crystallization . In this specimen heat-treated at 1300$\^{C}$, a lattice constant ratio(c/a) was 1.188. Scanning electron microscope(SEM) image of BaTiO$_3$ thin films of the specimen heat treated in between 900 and 1100$\^{C}$ shows a grain growth. At 1100$\^{C}$, the specimen stops grain-growing and becomes a poly-crystallization . A resistivity-temperature characteristics of the specimen depends on the doping concentrations of Mn. A resistivity ratio between the value at room temperature and the one above Curie temperature was 10$^4$ for pure BaTiO$_3$ thin films and 10$\^$5/ fo BaTiO$_3$ : additive 0.127mol% MnO

• Journal of Korean society of Dental Hygiene
• /
• v.4 no.2
• /
• pp.179-191
• /
• 2004

A series of experiments were conducted on dental denture base resins for their antibiosis. They were also compared in terms of physical and mechanical characteristics, which led to the following results: 1. As for bacterial deposition, the old products showed a wide range of distribution, while those products containing C. S. had restraints. 2. Among the products containing C. S., those ones of 7, 12 and 20% all had restraints of similar size to slop further bacterial growth. In the meanwhile, the old products had only small-size restraints for bacterial growth. 3. The following changes were observed in the aspect physical characteristics: There were no significance between the old products and the C. S. products. Thus, as for compressive force, the average${\pm}$standard deviation of the old products was $27.4083.{\pm}1.7397$, and those C. S. products of 20% showed the similar $27.5600{\pm}.1976$. In addition, there were no significance between the old products and those ones containing C. S. in terms of tensile force. The tensile force of the old products was $114.5600{\pm}.8916$ in average${\pm}$standard deviation, while there was no differences among the C. S. products of 7, 12, and 20% in that matter.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.217-217
• /
• 2009

This paper describes the characteristics of polycrystalline 3C-SiC doubly clamped beam micro resonators. The polycrystalline 3C-SiC doubly clamped beam resonators with 60 ~ 100 ${\mu}m$ lengths, $10\;{\mu}m$ width, and $0.4\;{\mu}m$ thickness were fabricated using a surface micromachining technique. Polycrystalline 3C-SiC micro resonators were actuated by piezoelectric element and their fundamental resonant frequency was measured by a laser vibrometer in vacuum at room temperature. For the 60 ~ 100 ${\mu}m$ long cantilevers, the fundamental frequency appeared at 373.4 ~ 908.1 kHz. The resonant frequencies of doubly clamped beam with lengths were higher than simulated results because of tensile stress. Therefore, polycrystalline 3C-SiC doubly clamped beam micro resonators are suitable for RF MEMS devices and bio/chemical sensor applications.

• Journal of the Korean Society for Heat Treatment
• /
• v.16 no.2
• /
• pp.90-96
• /
• 2003

The effect of betatizing temperature on microstructure and transformation characteristics in a Cu-AI-Ni based pseudoelastic alloy fabricated by heated mold continuous casting by using metallography, XRD and calorimetry. The microstructure of cast rod betatized at $600^{\circ}C$ revealed a ${\beta}_1$ parent phase and a ${\gamma}_2$ phase precipitated along the casting direction. When the cast rod was betatized at the elevated temperature above $600^{\circ}C$, the ${\gamma}_2$ phase is completely dissolved into the matrix so that the volume fraction of the ${\gamma}_2$ phase was decreased. The parent phase was stabilized by betatizing at $600^{\circ}C$. However, the ${\beta}_1$ parent phase was transformed to both ${{\beta}_1}^{\prime}$ and ${{\gamma}_1}^{\prime}$ martensites with increasing betatizing temperatures above $600^{\circ}C$, while $M_s$ and $A_s$ temperatures were decreased. The stress-strain curves for compression test were not same with betatizing temperature; the stress-strain curves of the specimen betatized at $600^{\circ}C$ and $700^{\circ}C$ were linear but those of the specimen betatized at $800^{\circ}C$ and $900^{\circ}C$ were not linear.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1820-1823
• /
• 2003

A high speed feeding type laser cutting M/C is developed for precise cutting of sheet metal. This paper has been carried out to obtain cutting characteristics and optimal cutting conditions of the developed high speed feeding type laser cutting M/C by a design of experiments. Cutting speed. laser power. laser duty and gas pressure are control factors for the surface roughness. The major factors affecting the surface roughness and the optimum cutting conditions are studied with minimum experiments using Taguchi method.