• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.04a
• /
• pp.82-87
• /
• 2012

Research and development of the spinning system which become bigger, faster and more detailed has been making progress continuously due to the increasing use of yarn which is considered as raw material to make industrial goods such as tire cord, air bag, filter, seatbelt and fiber-optic cable along with a remarkable growth of industry. In this paper, the desirable procedure and design requirements concerning a method of vibration reduction for "Godet Roller" considered as the main source of high vibration in the spinning system were suggested, and then verified those by analysis and actual test.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.2
• /
• pp.172-179
• /
• 2005

A high-precision centerless grinding machine has been recognized as a core equipment performing the finish outer-diameter grinding process of ferrules which are widely used as fiber optic connectors. In this study, in order to realize the high-precision centerless grinding machine, the structural characteristic analysis and evaluation are carried out on the virtual prototype consisted of the steel bed, hydrostatic GW and RW spindle systems, hydrostatic RW feed mechanism, RW swivel mechanism, and on-machine GW and RW dressers. The loop stiffnesses of centerless grinding machine are estimated based on the relative deformations between GW and RW caused by the grinding forces. And the simulated results illustrate that the concrete-filled bed has the considerable effect on the improvement of the structural stiffness of centerless grinding machine.

• Proceedings of the KIEE Conference
• /
• 1999.07e
• /
• pp.2139-2142
• /
• 1999

765kV substations which will be the core installation of the bulk power transmission system in Korea for the upcoming $21^{st}$ century, were designed of outdoor full GIS type to minimize required area. As principal equipment, main transformers of 2,000 MVA per bank and 50kA 8,000A gas insulated switchgears of up-to-date technology were adopted in designing substations to transmit bulk power of 10GW. Dual digital protective relay systems and distributed indication and control systems with fiber optic LAN were used.

• Advances in aircraft and spacecraft science
• /
• v.3 no.4
• /
• pp.427-445
• /
• 2016

Star sensors are the attitude estimation sensors of the satellite orbiting in its path. It gives information to the control station on the earth about where the satellite is heading towards. It captures the images of a predetermined reference star. By comparing this image with that of the one captured from the earth, exact position of the satellite is determined. In the process of imaging, stray lights are eliminated from reaching the optic lens by the mechanical enclosures of the star sensors called Baffles. Research in space domain in the last few years is mainly focused on increased payload capacity and reduction in launch cost. In this paper, a star sensor baffle made of Aluminium is considered for the study. In order to minimize the component weight, material wastage and to improve the structural performance, an alternate material to Aluminium is investigated. Carbon Fiber Reinforced Polymer is found to be a better substitute in this regard. Design optimisation studies are carried out by adopting suitable design modifications like implementing an additional L-shaped flange, Upward flange projections, downward flange projections etc. A better configuration of the baffle, satisfying the design requirements and achieving manufacturing feasibility is attained. Geometrical modeling of the baffle is done by using UNIGRAPHICS-Nx7.5(R). Structural behavior of the baffle is analysed by FE analysis such as normal mode analysis, linear static analysis, and linear buckling analysis using MSC/PATRAN(R), MSC-NASTRAN(R) as the solver to validate the stiffness, strength and stability requirements respectively. Effect of the layup sequence and the fiber orientation angle of the composite layup on the stiffness are also studied.

• Korean Journal of Optics and Photonics
• /
• v.17 no.1
• /
• pp.7-17
• /
• 2006

In this paper, we proposed an optical true time-delay (TTD) for planar phased array antennas (PAAs), which is composed of a wavelength-dependent optical true time delay (WDOTTD) followed by a wavelength-independent optical true time delay (WIOTTD). The WDOTTD is a fiber Bragg gratings (FBGs) Prism and the WDOTTD is a fiber delay-lines matrix of which each component consists of a certain length of fiber connected to cross-ports of a 2${\times}$2 MEMS switch. A 10-GHz 2-bit${\times}$4-bit two-dimensional optical TTD has been fabricated by cascading a WDOTTD with a maximum time delay of 810 ps to a WIOTTD of $\pm$50 ps. Time delay and insertion loss for each radiation angle have been measured. Time delay error for the WIOTTD has been measured to be less than $\pm$1 ps. We have also designed a two-dimensional 10-GHz PAA composed of 8${\times}$8 microstrip patch antenna elements driven by the proposed TTD. The radiation patterns of this PAA have been obtained by simulation and analyzed.

• Journal of the Korean Magnetics Society
• /
• v.6 no.1
• /
• pp.36-39
• /
• 1996

We have constructed a disp1acerrent sensor for measuring dynamic magnetostriction of an arrvrphous ribbon under alternating magnetic field using fiber optic Fabry-Perot interferorreter. The signal of the sensor was depen¬dent on the index matching oil and the optical isolator. The resolution of the sensor was $30{\AA}$ and the measured peak to peak magnetostriction of the amorphous ribbon $Fe_{81}B_{13.5}Si_{3.5}C_{2}$ was $28{\times}10^{-6}$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.8
• /
• pp.12-17
• /
• 2009

We have implement어 a bust mode optical transmitter using digital temperature compensation architecture with a microprocessor. Instead of previous analog real time technique, we used digital sampling and holding technique for the temperature compensation in order to get stable high speed data transmission of the laser diode. This digital temperature compensation technique should be complemented the previous analog method with accuracy and effectiveness in the over Gb/s transmitting application.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.1 s.178
• /
• pp.193-200
• /
• 2006

To perform the finish grinding process of ferrules which are widely used as fiber optic connectors, a high-precision centerless grinding machine is necessary. The high-precision centerless grinding machine is consisted of the hydrostatic GW and RW spindle systems, hydrostatic RW feeding mechanism, RW swivel mechanism, on-machine GW and RW dressers, and concrete-filled steel bed. In this study, the thermal characteristics of the high-precision centerless grinding machine such as the temperature distribution, temperature rise and thermal deformation, are estimated based on the virtual prototype of the grinding machine and the heat generation rates of heat sources related to the machine operation conditions. The reliability of the predicted results is demonstrated by the temperature characteristics measured from the physical prototype. Especially, the predicted and measured results show the fact that the high-precision centerless grinding machine has very stable thermal characteristics.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.509-514
• /
• 2001

The Fibre-optic Bragg grating (FBG) sensor is broadly accepted as a structural health monitoring device for Fibre reinforced plastic (FRP) materials by either embedding into or bonding onto the structures. The accuracy of the strain measured by using the FBG sensor is highly dependent on the bonding characteristics among the bare optical fibre, protective coating, adhesive layer and host material. In general, the signal extracted from the embedded FBG sensor should reflect the straining condition of the host structure. This paper presents a theoretical model to evaluate the differential strains between the bare fibre and host material with different adhesive thickness and modulus of the protective coating of the embedded FBG sensor.

• Journal of Internet Computing and Services
• /
• v.13 no.3
• /
• pp.17-22
• /
• 2012

In this paper, a photoelectric image detection system is proposed using an APD(Avalanche Photodiode) sensor, a LED illuminator, and fiberoptic waveguides. This proposed pinhole detection system can detect the pinholes of 100 micron with the speed rate of 1,000mpm(meter per minute). And detecting performance of image system is improved by the SQL based DB analysis of classifying pinhole's detected location and size using image detection algorithms.