• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.05a
• /
• pp.125-130
• /
• 2001

A existing design method of PSC girder bridges, according to total service loads, stress required tendon force at a time. Because this design method increases beam depth, design of long span is difficult. However, As UC girder stressing at difficult loading stages reduces sectional depth of PSC girder, both design and operation of long span bridges is possible. so, this study analyzes the effect of design parameter (Girder Strength, Girder Spacing, Span Length, Joint Strength) on the beam depth of IPC girder continuous bridges, and shows sectional depth of UC girder for design of long span bridges. According to analysis, when a continuous bridges of same length span is at strength of joint over strength of girder of 600kg/$cm^{2}$, a change of beam depth is observed and when a continuous bridges of different span length is at strength of joint below strength of girder of 600kg/$cm^{2}$, a change of beam depth is observed. In two case, a change of beam depth is mostly observed over strength of girder of 350kg/$cm^{2}$ according to analysis of deflection data, a continuous bridges of IPC girder is nearly satisfied.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.25 no.1
• /
• pp.83-88
• /
• 2016

Because of the increasing tool cost for cutting hard-to-cut materials, abrasive water jet (AWJ) milling recently has been regarded as a potential alternative machining method. However, it is difficult to control the depth and width of cut in AWJ milling because they vary depending on many AWJ cutting parameters. On 27 conditions within a limited range of pressure, feed rate, and abrasive flow rate, AWJ cutting was conducted on titanium, and depth profiles were measured with a laser sensor. From the depth profile data, depth and width of cut were acquired at each condition. The relationships between depth and parameters and between width and parameters were derived through regression analysis. The former can provide proper cutting conditions and the latter the proper pick feed necessary to generate a milled surface. It is verified that pressure mostly affects depth, whereas abrasive flow rate mostly affects width.

• IEIE Transactions on Smart Processing and Computing
• /
• v.3 no.4
• /
• pp.195-204
• /
• 2014

This paper presents the depth evaluation for object detection by automated assembling robots. Pattern distortion analysis from a structured light system identifies an object with the greatest depth from its background. An automated assembling robot should prior select and pick an object with the greatest depth to reduce the physical harm during the picking action of the robot arm. Object detection is then combined with a depth evaluation to provide contour, showing the edges of an object with the greatest depth. The contour provides shape information to an automated assembling robot, which equips the laser based proxy sensor, for picking up and placing an object in the intended place. The depth evaluation process using structured light for an automated electronics assembling robot is accelerated for an image frame to be used for computation using the simplest experimental set, which consists of a single camera and projector. The experiments for the depth evaluation process required 31 ms to 32 ms, which were optimized for the robot vision system that equips a 30-frames-per-second camera.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.10
• /
• pp.1131-1137
• /
• 2012

Subsea pipelines have been operated with buried depths of 1.2-4m underneath the seabed to prevent buoyancy and external impacts. Therefore, they have to show resistance to both the soil load and the hydrostatic pressure. In this study, the structural integrity of a subsea pipeline subjected to soil load and hydrostatic pressure was evaluated by using FE analyses. A parametric study showed that the internal pressure increased the plastic collapse depth by increasing the resistance to plastic collapse. The hoop stress increased with an increase in the buried depth for the same water depth; however, the hoop stress decreased with an increase in the water depth for the same buried depth.

• The Journal of Korean Institute of Information Technology
• /
• v.17 no.8
• /
• pp.75-83
• /
• 2019

In this paper, we propose a method that can detect and trace the end point of real - time reinforcement steel to various environmental conditions of industrial field by using Median flow and Depth information. We proposed a method to derive two steel end points by using Median filter, Binarization, Morphology, and Blob algorithm on image depth information. The coordinates of the final position were determined by comparing the coordinates of the reinforcement steel endpoints detected in the Depth image and the position tracking coordinates of the reinforcement steel using Median Flow. As a result, when the existing Median Flow method was used, the success rate of the final position determination of reinforcement steel of 75% was increased to 95% when the Depth of reinforcement steel was used.

• Journal of Biomedical Engineering Research
• /
• v.28 no.2
• /
• pp.287-293
• /
• 2007

The researchers have studied for a long time about the depth of anesthesia but they don't make criteria for the depth of anesthesia. Anesthetists can't make a prediction about patient's reaction. Therefore, patients have potential risk such as poisonous side effect, late-awake, early-awake and strain reaction. In this study, the distributed characteristics on the bispectrum and bicoherence, the type of nonlinear signal processing, as a result of the coupling of EEG were presented according to depth of anesthesia. These results were consistent with a trend of delta ratio that the index of evaluation for the depth of anesthesia. The higher-order spectrum (HOS), the bispectrum and bicoherence, gives the useful information about depth of anaesthesia than other indexes.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.04c
• /
• pp.6-9
• /
• 2008

A 3D depth measurement system is proposed for mobile vehicles. Depth measurement system which is composed of a rotating mirror, a line laser and mono-camera is employed to detect depth, where the laser light is reflected by the mirror and projected to- the scene objects whose locations are to be determined. The obtained depth information is converted into an image. Such depth images of the road region represent even and plane while that of off-road region is irregular or textured. Road region is detected employing a simple spatial differentiation technique to detect the plain textured area. Identification results of the diverse situation of Non-linear trail are included in this paper.

• Journal of Korea Multimedia Society
• /
• v.19 no.4
• /
• pp.774-779
• /
• 2016

The conventional methods using color signal for tracking the movement of the object require a lot of calculation and the performance is not accurate. In this paper, we propose a method to effectively track the moving objects using the depth information from a depth camera. First, it separates the background and the objects based on the depth difference in the depth of the screen. When an object is moved, the depth value of the object becomes blurred because of the phenomenon of Motion Blur. In order to solve the Motion Blur, we observe the changes in the characteristics of the object (the area of the object, the border length, the roundness, the actual size) by its velocity. The proposed algorithm was implemented in the simulation that was applied directly to the tracking of a golf ball. We can see that the estimated value of the proposed method is accurate enough to be very close to the actual measurement.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.51 no.4
• /
• pp.362-368
• /
• 2006

A pot experiment was conducted to investigate the effects of soil burial depth on seedling emergences of rice (Oryza sativa) and Echinochloa spp. and to model such effects for mathematical prediction of seedling emergences. When the Gompertz curve was fitted at each soil depth, the parameter C decreased in a logistic form with increasing soil depth, while the parameter M increased in an exponential form and the parameter B appeared to be constant. The Gompertz curve was combined by incorporating the logistic model for the parameter C, the exponential model for the parameter M, and the constant for the parameter B. This combined model well described seedling emergence of rice and Echinochloa species as influenced by soil burial depth and predicted seedling emergence at a given time after sowing and a soil burial depth. Thus, the combined model can be used to simulate seedling emergence of crop sown in different soil depths and weeds present in various soil depths.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.17 no.3
• /
• pp.183-196
• /
• 2015

This study aims to develop sleeve pattern of tailored jacket which shows seamlessly beauty of females in their twenties who have relatively smaller change of body compared people of other ages and has outstanding functional operation. So we selected a pattern of manufacturer who received highest score after evaluating wearing condition of three types of jacket in the industry, whose targets are career women in their twenties and then tested its appearance and functional operation of 6 experimental jackets with armhole depth of B/4 and B/4-1(cm) along with sleeve cap height of A.H/3, A.H/3+1, A.H/3+2. As a result, the pattern which has good result of external appearance evaluation were sleeve with armhole depth of B/4-1 and sleeve cap height of A.H/3+2 as well as sleeve with armhole depth of B/4-1 and sleeve cap height of A.H/3+1. The pattern of good result for movement adaptation were sleeve with armhole depth of B/4-1 and sleeve cap height of A.H/3 as well as sleeve with armhole depth of B/4 and sleeve cap height of A.H/3. So we could find that the larger is the armhole depth and height of sleeve, the better influence on adaptability of jacket it makes and that the smaller is the armhole depth and height of sleeve, the better influence on movement adaptability of jacket it makes. It has been proved that armhole depth of tailored jacket of females in their twenties doesn't affect significantly on its appearance when designing it but it makes good influence on movement adaptability when experimental clothing has armhole depth of B/4-1and that sleeve cap height of A.H/3 that is 1cm shorter than A.H/3+1 which is used in industry makes good influence on appearance and functional operation.