• 한국정보통신학회논문지
• /
• 제8권2호
• /
• pp.494-498
• /
• 2004

본 연구에서는 생체인식(Biometric)을 이용하여 Access Control System을 구현하였다. Biometrics는 생체인식 또는 생체 측정학으로 사람의 생체적, 행동적 특성을 이용하여 개인을 식별하는 학문 또는 기술이다. Access Control System은 개인을 식별 출입과 근태, 개인 관리, 보안 등에 사용하는 System으로 Biometric System과 접목으로 편리성과 보안성에서 탁월한 효과을 발휘할 수 있다. 본 연구에서 제안한 시스템은 기존의 RF Card System에 Wiegand(Data format) Signal 출력으로 기존 RF Card Reader대신 Access Control (Security) System을 구성할 수 있도록 설계되었고 컴퓨터와 RS-232, RS-422 또는 TCP/IP 로 구성되어 Software상에서 임베이디드 System을 Control 할 수 있게 되어 있다.

• 전자공학회논문지A
• /
• 제33A권4호
• /
• pp.11-17
• /
• 1996

In the case of redundancy control performed by a netowrk management system, it can not be ignored some delay of control time and break of control by failure of the system. This paper proposed a new method to improve the performacne of a redundancy control system interfaced to the network management system. At first, it produced the modelling of the total system and analyzed the functional relation of reliability and failure rate for a transmission system having an one-to-one active redundancy structure controlled by itself. After describing the loss rate of transmission data and the time required for the redundancy control process of the network management system when a failure is occurred, it proposed the new redundancy method of complex system control mode as an effective redundancy control method to improve reliability of a redundancy control system. Finally, it proved the effect by comparing the new result to the previous result.

• 드라이브 ㆍ 컨트롤
• /
• 제16권2호
• /
• pp.59-65
• /
• 2019

Hydraulic systems have severe nonlinearity inherently compared to other systems like electric control systems. Hence, precise modeling and analysis of the hydraulic control systems are not easy. In this study, the control performance of a hydraulic control system with a feedback linearization compensator and a disturbance observer was analyzed through experiments and numerical simulations. This study mainly focuses on the quantitative investigation of sensitivity on system uncertainties in the hydraulic control system. First, the sensitivity on the system uncertainty of the hydraulic control system with a Feedback Linearization - State Feedback Controller (FL-SFC) was quantitatively analyzed. In addition, the efficacy of a disturbance observer coupled with the FL-SFC for the hydraulic control system was verified in terms of overcoming the control performances deterioration owing to system uncertainty.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.2696-2700
• /
• 2003

Nuclear robots should be developed for the reduction of radiation exposure, lower man hours, shorter power outage, and also improved worker safety concerns in performing hazardous and dangerous tasks. Among the components of a nuclear robot system, a robot control system equivalent to a human brain is a crucial point because a nuclear robot does not work without a control system. Therefore, in this paper, we will explain the requirements for a robot control system for a nuclear robot from a general point of view and also review the robot control systems of nuclear robots that were developed domestically, to assist a researcher beginning with the design for the control system of nuclear robots. The explained robot control system will be useful to develop the control system for industrial robots, home robots and other robots which are needed for tele-operation and are controlled through the internet.

• Journal of Biosystems Engineering
• /
• 제27권2호
• /
• pp.79-88
• /
• 2002

This study was conducted to develop system for high speed rice transplanting machines. The control system includes a sensor detecting the tilt angle of the seedling bed, a micro-controller and a hydraulic system consisting of a double acting cylinder, a four-way three-position solenoid valve, a relief valve and a hydraulic pump. The levelling system shared the pump with the existing steering control, resulting in a tandem center circuit for the steering and levelling control systems. Using the input signal from the sensor, the micro-controller determined and generated the output signal to control the cylinder through the solenoid valve to keep the seedling bed always parallel to the water surface regardless of soil unevenness during the transplanting operations. Both an ON/OFF and a PWM control schemes were tested. When the flow rate was more than 1 ι/min in the ON/OFF control, the system showed unstable rolling. However, in the PWM control, the system worked stably although the flow rate was more than 1 ι/min. The PWM control showed a better performance when a large difference between the angle and the dead band of the control system occurred. The characteristics of tile system response to given tilt angles were predicted by a computer simulation. Both the ON/OFF and the PWM control systems worked well providing that the operating and waiting times were properly adjusted.

• 농업과학연구
• /
• 제37권1호
• /
• pp.123-130
• /
• 2010

A steering control system based on CAN(Controller Area Network) for autonomous tractor was developed to reduce duty of a central processing computer and to improve performance of steering control in terms of reduced control interval and error. The steering control system consisted of a SCU (Steering Control Unit), an EHPS system, and a potentiometer. The SCU consisted of an MCU (Micro Controller unit), an A/D converter, and a DC-DC converter, and a PID controller was used to control steering angle. The steering control system was communicated with the computer by CAN-bus. Each actuator and implement was connected to a multi-function board interfacing with the computer through a USB cable. Without CAN, control interval of the autonomous tractor was 1.5 seconds. When the CAN-based steering control system was combined with the autonomous tractor, however, control interval of the integrated system was reduced to those less than 0.05 seconds. When the autonomous tractor was operated with 1.5-s and 0.05-s control cycles at a 0.63-m/s travelling speed, the trajectories were close to straight lines for both of the control cycles. For a 1.34-m/s traveling speed, tractor trajectory was close to sine wave with a 1.5-s control cycle, but was straight line with a 0.05-s control cycle.

• 소음진동
• /
• 제8권2호
• /
• pp.283-288
• /
• 1998

If one wants to control the noise from a duct, then one must have sufficient number of sensors and actuators so that the control system is observable and controllable. A number of sensors and actuators for control of radiating noise from a duct have to be incorporated with the number of modes which one wants to control. These considerations motivated the present study that considers a control system which has less microphones and actuators than required. In this work, by theoretical analysis and numerical simulation, the control performance and robust reliability of such a kind of control system is investigated in terms of sound-field variables and control system variables. Then the possibility of implementation of the robust radiation power control system is verified by theoretical analysis and numerical simulation. In addition, the control performance of the control system is verified by experiment.

• 풍력에너지저널
• /
• 제2권1호
• /
• pp.90-96
• /
• 2011

The purpose of this paper is to describe the control system for optimal performance of 2MW gearless PMSG wind turbine system, and to afford some techniques of the algorithm selection and design optimization of the wind turbine control system through analysis of load calculation and control characteristic. Wind turbine control system is composed of the main control system and remote control and monitoring system. The main control system is industrial PC based controller, and the remote control and monitoring system is a server based computer system. The main control system has a supervisory control of the wind turbine with operation procedures and power-speed control through the torque control by pitch angle. There are some applications to optimize the wind turbine system at the starting mode with increasing of rotor speed, and cut-in operating mode to prevent trundling cut-in and cut-out, a gain scheduling of pitch PID controller, torque scheduling and limitation of generation power by temperature limitation or remote command by remote control and monitoring system. Also, the server operation program of the remote control and monitoring system and the design of graphical display are described in this paper.

• Asia pacific journal of information systems
• /
• 제5권1호
• /
• pp.112-128
• /
• 1995

The information system control includes organizational structure, control mechanism, and management tools which contribute to accomplish the goals of information system: asset safeguarding, data integrity, effectiveness, and efficiency. Information system audit is the process to evaluate whether the information system accomplishs the goals. Information system auditor examine the reliability of information system control and suggest recommendations to improve the information system control. Both information system control and information system audit activities contribute to prevent and detect the computer crime for the organization. This paper proposes a causal model of information system control/audit and the perceived risk of computer crime, and tests the model using a survey on 38 financial institutions in Korea. Statistical results show that information system control and audit significantly reduce the computer crime risk perceived by the user group. The general control has a stronger impact than the application control. In addition, it turns out that the greater the deviation between the importance and the actual level of information system control is, the higher the perceived risk of computer crime is.

• Smart Structures and Systems
• /
• 제3권1호
• /
• pp.115-131
• /
• 2007

The electromechanical integrated toroidal drive is a new drive system. For the control of the drive, the torque fluctuation and the steady-state errors should be removed and the fast response to the input change should be achieved. In this paper, the torque fluctuation of the drive system is analyzed and expressed as Fourier series forms. The transfer function of the torque control for the drive system is derived from its electromechanical coupled dynamic equations. A 2-DOF control method is used to control the drive system. Using definite parameter relationship of the 2-DOF control system, the steady errors of the torque control for the drive system is removed. Influences of the drive parameters on the control system are investigated. Using proper drive parameters, the response time of the control system is reduced and the quick torque response of the drive system is realized. Using a compensated input voltage, the torque fluctuation of the drive system is removed as well. The compensated input voltage can be obtained from the torque fluctuation equation and the transfer function. These research results are useful for designing control system of the new drive.