• Journal of the Korean Geotechnical Society
• /
• v.35 no.7
• /
• pp.5-14
• /
• 2019

In this study, a prototype abutment was constructed to establish a safety assessment technique of pier and a series of non-destructive tests using impact load. The surcharge load was loaded from 0 tonf to 2.5 tonf on the prototype abutment, and maximum surcharge load was up to 25 tonf. To analyze the behavior of the piers according to the direction of impact, a total of three types of analysis were performed: the direction of the pier, the direction perpendicular to the pier, and the outer direction of the pier. The height of the impact was also tested at each top and bottom. The measuring instrument used an accelerometer to measure the acceleration response when impacted. Based on the series of experimental results, specific values were calculated according to the direction of an impact and the surcharge load using the Fast Fourier Transform (FFT). In addition, the phase difference was used to analyze the pier from the primary 1st mode to the 4th mode.

• Earthquakes and Structures
• /
• v.22 no.2
• /
• pp.185-201
• /
• 2022

Structural Health Monitoring (SHM) is used to provide reliable information about the structure's integrity in near realtime following extreme incidents such as earthquakes, considering the inevitable aging and degradation that occurs in operating environments. This paper experimentally investigates an integrated wireless sensor network (Wi-SN) based monitoring technique for damage detection in concrete structures. An effective SHM technique can be used to detect potential structural damage based on post-earthquake data. Two novel methods are proposed for damage detection in reinforced concrete (RC) building structures including: (i) Jerk Energy Method (JEM), which is based on time-domain analysis, and (ii) Modal Contributing Parameter (MCP), which is based on frequency-domain analysis. Wireless accelerometer sensors are installed at each story level to monitor the dynamic responses from the building structure. Prior knowledge of the initial state (immediately after construction) of the structure is not required in these methods. Proposed methods only use responses recorded during ambient vibration state (i.e., operational state) to estimate the damage index. Herein, the experimental studies serve as an illustration of the procedures. In particular, (i) a 3-story shear-type steel frame model is analyzed for several damage scenarios and (ii) 2-story RC scaled down (at 1/6th) building models, simulated and verified under experimental tests on a shaking table. As a result, in addition to the usual benefits like system adaptability, and cost-effectiveness, the proposed sensing system does not require a cluster of sensors. The spatial information in the real-time recorded data is used in global damage identification stage of SHM. Whereas in next stage of SHM, the damage is detected at the story level. Experimental results also show the efficiency and superior performance of the proposed measuring techniques.

• Animal Bioscience
• /
• v.36 no.5
• /
• pp.810-817
• /
• 2023

Objective: The aim was to compare the behavioral response to full separation of cows and calves maintained together for 100 days or 24 h. Methods: Twelve Holstein-Friesian cow-calf pairs were enrolled into either treatment or industry groups (n = 6 cow-calf pairs/group). The treatment cows and calves were maintained on pasture together for 106±8.6 d and temporarily separated twice a day for milking. The Industry cows and their calves, were separated within 24 h postpartum. Triaxial accelerometer neck-mounted sensors were fitted to cows 3 weeks before separation to measure hourly rumination and activity. Before separation, cow and calf behavior was observed by scan sampling for 15 min. During the separation process, frequency of vocalizations and turn arounds were recorded. At separation, cows were moved to an observation pen where behavior was recorded for 3 d. A CCTV camera was used to record video footage of cows within the observation pens and behavior was documented from the videos in 15 min intervals across the 3 d. Results: Before separation, industry calves were more likely to be near their mother than Treatment calves. During the separation process, vocalization and turn around behavior was similar between groups. After full separation, treatment cows vocalized three times more than industry cows. However, the frequency of time spent close to barrier, standing, lying, walking, and eating were similar between industry and treatment cows. Treatment cows had greater rumination duration, and were more active, than industry cows. Conclusion: These findings suggest a similar behavioral response to full calf separation and greater occurrence of vocalizations, from cows maintained in a long-term, pasture-based, cow-calf rearing system when ompared to cows separated within 24 h. However, further work is required to assess the impact of full separation on calf behavior.

• Asia-pacific Journal of Multimedia Services Convergent with Art, Humanities, and Sociology
• /
• v.7 no.1
• /
• pp.177-186
• /
• 2017

Recently, Autonomous vehicles are getting hot attention. Amazon, the biggest online shopping service provider is developing a delivery system that uses drones. This kinds of platforms are need accurate attitude information for navigation. In this paper, a structure design of AHRS using low-cost inertia sensor is proposed. To estimate attitudes a Kalman filter which uses a quaternion based dynamic model, bias-removed measurements from MEMS Gyro, raw measurements from MEMS accelerometer and magnetometer, is designed. To remove bias from MEMS Gyro, an additional Kalman filter which uses raw Gyro measurements and attitude estimates, is designed. The performance of implemented AHRS is compared with high price off-the-shelf 3DM-GX3-25 AHRS from Microstrain. The Gyro bias was estimated within 0.0001[deg/s]. And from the estimated attitude, roll and pitch angle error is smaller than 0.2 and 0.3 degree. Yaw angle error is smaller than 6 degree.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.1
• /
• pp.30-35
• /
• 2017

In this study, we measured the natural frequencies of aluminum honeycomb sandwich beams using digital image correlation technique. The vibration images were captured using two high speed digital cameras and the images were converted to displacements by the digital image correlation technique. Displacement data in time domain were tranformed to frequency domain data by fast Fourier transform software. To reduce noise invoked by random exitation, a spectrum averaging technique and Savitsky-Golay digital filter were adopted. A conventional vibration measurement using an accelerometer and a finite element analysis were performed to compare the results by high speed digital camera measurement method. In conclusion, new method using high speed digital cameras and digital image correlation technique can measure the vibration of beam structures and can be applied to bio-structures where sensors cannot be attached.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.45 no.3
• /
• pp.135-141
• /
• 2008

We propose a new method for recognizing the activities of daily living(ADL) based on the state-dependent motion analysis using 3-axial accelerometers and a glove type RFID reader. Two accelerometers are used for the classification of 5 body states based on the decision tree. Classification of the instrumental activities is performed based on the hand interaction with an object ID using an accelerometer and a RFID reader. Object-dependent hand movements are classified into 5 categories in advance and final decision combines the body state and the instrumental activities. Experiment shows that the suggested hierarchical motion analysis provides accuracy rate of over 90% for all 20 ADLs.

• Journal of Sensor Science and Technology
• /
• v.8 no.1
• /
• pp.53-62
• /
• 1999

Micro polysilicon actuators, which are widely used in the field of MEMS (Microelectromechanical System) technology, were fabricated using polysilicon thin layers. Polysilicon deposition were carried out to have symmetrical layer structures with a LPCVD (Low Pressure Chemical Vapor Deposition) system, and we have measured physical characteristics by micro test patterns, such as bridges and cantilevers to verify minimal mechanical stress and stress gradient in the polysilicon layers according to the methods of mutilayer deposition, doping, and thermal treatment, also, analyzed the properties of each specimen, which have a different process condition, by XRD, and SIMS etc.. Finally, the fabricated planar polysilicon resonator, symmetrically stacked to $6.5{\mu}m$ thickness, showed Q of 1270 and oscillation ampitude of $5{\mu}m$ under DC 15V, AC 0.05V, and 1000 mtorr pressure. The developed micro polysilicon resonator can be utilized to micro gyroscope and accelerometer sensor.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.607-611
• /
• 2006

There are several methods to obtain structural vibration for analysis of vibro-acoustic noise. First of all, vibration data can be obtained through the structural analysis using finite element method. Although this method has no need to experiment, the analysis result is unreliable when the structure and the vibration source is complex to model exactly. The second method is to measure vibration using a number of sensors. The analyzed vibro-acoustic noise with directly measured data is setting morereliable when the number of data acquisition points is getting larger. However, it requires large amount of time and effort to measure all vibration data on every node especially when the size of vibrating structure is large. The Modal Expansion Method(MEM), which uses mode information and measurement data, has been introduced to compensate their limits. With a relatively small number of measurement data, the reliable structural vibration for vibro-acoustic noise can be obtained using this semi-analysis method. Although MEM gives reliable result, it is restricted by the number of modes and measurement points. In this paper, structural analysis, direct vibration measurement method and MEM are compared using the simple aluminum box model. Furthermore, the washing machine case is also provided as a comparative example. The Laser Doppler Vibrometer(LDV) was used instead of contact type accelerometer to get vibration data.

• Journal of KIISE
• /
• v.44 no.4
• /
• pp.374-382
• /
• 2017

As the walking exercise is emphasized in personalized healthcare, numerous services demand walking information. Along with the propagation of smartphones nowadays, many step-counter applications have been released. But these applications are error-prone to abnormal movements such as simple shaking or vibrations; also, different step counts are shown when the phone is positioned in different locations of the body. In this paper, the proposed method accurately counts the steps regardless of the smartphone position by using an accelerometer and a proximity sensor. A threshold is set on each of the six positions to minimize the error of undetection and over-detection, and the cut-off section is set to eliminate any noise. The test results show that the six position type were successfully identified, and through a comparison experiment with the existing application, the proposed technique was verified as superior in terms of accuracy.

• Journal of the Korean Institute of Gas
• /
• v.4 no.1 s.9
• /
• pp.1-8
• /
• 2000

Third party damage is one of the causes intrimiting the safety of a buried pipelines and it is very important to detect third party damage on pipelines as soon as possible. The purpose of this study is whether third-party damage can be detected by accelerometer sensor and how far the third-party damage signal can propagate. And a pilot experiment was carried out in order to find third-party damage location. As a result, the detected signal's spectum is high frequency at short distances, as the distance is far, the signals in high frequency range are attenuated and those in low frequency range remain. It was also proved that third-party damage within 5.3km distance can be detected by monitoring vibration signals.