• International Journal of Naval Architecture and Ocean Engineering
• /
• 제13권1호
• /
• pp.877-888
• /
• 2021

The water entry behaviors of projectiles with different cone-headed angles were studied numerically, experimentally and theoretically, mainly focusing on the hydrodynamic impact in the initial stage. Based on MMALE algorithm, it was proposed a formula of impact deceleration, which relied on the initial entry velocity and cone-headed angle. Meanwhile, in order to verify the validity of the simulation model, experiments using accelerometer and high-speed camera were carried out, and their results were in a good agreement with simulation results. Also, theoretical calculation results of cavity diameter were compared with experiments and simulation results. It was observed that the simulation method had a good reliability, which would make forecast on impact deceleration in an engineering project.

• 지능정보연구
• /
• 제17권1호
• /
• pp.53-69
• /
• 2011

로봇 자체 또는 로봇에 탑재된 콘텐츠와의 상호작용을 위해 일반적으로 영상 또는 음성 인식 기술이 사용된다. 그러나 영상 음성인식 기술은 아직까지 기술 및 환경 측면에서 해결해야 할 어려움이 존재하며, 실적용을 위해서는 사용자의 협조가 필요한 경우가 많다. 이로 인해 로봇과의 상호작용은 터치스크린 인터페이스를 중심으로 개발되고 있다. 향후 로봇 서비스의 확대 및 다양화를 위해서는 이들 영상 음성 중심의 기존 기술 외에 상호보완적으로 활용이 가능한 인터페이스 기술의 개발이 필요하다. 본 논문에서는 로봇 인터페이스 활용을 위한 가속도 센서 기반의 제스처 인식 기술의 개발에 대해 소개한다. 본 논문에서는 비교적 어려운 문제인 26개의 영문 알파벳 인식을 기준으로 성능을 평가하고 개발된 기술이 로봇에 적용된 사례를 제시하였다. 향후 가속도 센서가 포함된 다양한 장치들이 개발되고 이들이 로봇의 인터페이스로 사용될 때 현재 터치스크린 중심으로 된 로봇의 인터페이스 및 콘텐츠가 다양한 형태로 확장이 가능할 것으로 기대한다.

• 제어로봇시스템학회논문지
• /
• 제22권9호
• /
• pp.705-709
• /
• 2016

Micro-electro-mechanical systems (MEMS) gyroscopes are widely used in various robot applications. However, these conventional gyroscopes need to vibrate the proof mass using a built-in actuator at a fixed resonance frequency to sense the Coriolis force. When a robot is not moving, the meaningless vibration of the gyroscope wastes power. In addition, this continuous vibration makes the sensor vulnerable to external sound waves with a frequency close to the proof-mass resonance frequency. In this paper, a feasibility study of a new type of gyroscope inspired by insect halteres is presented. In dipterous insects, halteres are a biological gyroscope that measures the Coriolis force. Wing muscles and halteres are mechanically linked, and the halteres oscillate simultaneously with wing beats. The vibrating haltere experiences the Coriolis force if the insect is going through a rotational motion. Inspired by this haltere structure, a gyroscope using a thin mast integrated with a robot actuation mechanism is proposed. The mast vibrates only when the robot is moving without requiring a separate actuator. The Coriolis force of the mast can be measured with an accelerometer installed at the tip of the mast. However, the signal from the accelerometer has multiple frequency components and also can be highly corrupted with noise, such that raw data are not meaningful. This paper also presents a suitable signal processing technique using the amplitude modulation method. The feasibility of the proposed haltere-inspired gyroscope is also experimentally evaluated.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2010년도 추계학술대회 논문집
• /
• pp.236-241
• /
• 2010

This paper presents a wear diagnosis method for centrifugal impellers by using an accelerometer. The features are calculated from raw and wavelet transformed signals with several statistical methods applied in time or frequency domains. From the effectiveness coefficient test, it is shown that 7th level of wavelet transformed signal is suitable for wear classification problems. A neural network with 5 feature sets is applied to diagnose the wear magnitude of pump impellers. The verification result reveals that high accuracy for the wear diagnosis of impellers can be obtained by using wavelet features transformed from acceleration signals.

• 한국음향학회:학술대회논문집
• /
• 한국음향학회 2000년도 하계학술발표대회 논문집 제19권 1호
• /
• pp.279-282
• /
• 2000

진동가속도를 감지하는 힘평형 서보 가속도계의 성능특성을 결정하는 질량지지 장치를 4개의 팔로 구성된 형태로 설계하고 응답특성을 조사하였다. 스프링의 길이, 폭, 두께에 따른 질량지지 장치의 응답특성을 유한요소법을 이용하여 계산하고, 이를 바탕으로 힘평형 서보 가속도계의 감도, 사용주파수 범위 및 동적 범위를 예측하였다. 그리고 레이저 간섭계를 이용하여 힘평형 서보 가속도계의 각각의 진동 주파수 및 가속도의 크기에 따른 간섭무의 수의 변화와 이때의 응답전압간을 이용하여 가속도계의 응답특성을 측정하였으며, 수치해석을 통해 얻은 결과와 비교 분석하였다.

• 동력기계공학회지
• /
• 제3권4호
• /
• pp.57-62
• /
• 1999

The microaccelerometer using a tunnelling current effect concept has the potential of high performance, although it requires slightly complex signal-processing circuit for servo-system. The paddle of micro accelerometer is pulled to have the gap width of about 2nm which almost allows the flow tunnelling current. This paper demonstrates at capacitor of microaccelerometer the use of the coupled thermo-electric analysis for voltage, current, heat flux and Joule heating then tunnelling current flows. Two electrodes are applied to the microaccelerometer producing a unform difference of temperature gradient and electric potential between the paddle and the substrate.

• 한국포장학회지
• /
• 제12권1호
• /
• pp.21-25
• /
• 2006

Measurements of accelerometer levels transmitted from the floor in commercials truck shipments were carried out transportation of 300 Kg-load from Gyungbu Highway(Waegouan-Seoul) to 88 Highway(Gwangju-Daegu). Different characteristics were observed the values measured the vibration levels with directions in the two Highway's as a function of road condition and truck speed. The results showed that the vibration levels of the Gyungbu Highway is much higher than those of the 88 Highway. A following analysis on the obtained values was used to get the acceleration spectral density (ASD) and power spectral density (PSD). For the entire transit route, the results showed that the level of vibration to vertical direction was significant effects for damaging the products carried compared to other directions such as longitudinal and transverse. This paper provides an updated history of measured characteristics of vibration levels for highways using mainly in domestic area.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 추계학술대회 논문집
• /
• pp.70-75
• /
• 1993

Chatter vibration is an unwanted phenomenon in metal cutting and it always affects surface finish, tool life machine life and the productivity of machining process. The In-process monitoring & control of chatter vibration is necessarily required to automation system. In this study, we constructed the multi-sensing system using Tool Dynamometer,Accelerometer and AE(Acoustic Emission) sensor for the credible detection of chatter vibration. And a new approach using a neural network to process the features of multi-sensor for the recognition of chatter vibration in turning operation is proposed. With the back propagation training process, the neural network memorize and classify the feature difference of multi-sensor signals.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1433-1437
• /
• 2005

Until now, strain gage technique and accelerometer for the diagnosis safety of constructions are used widely. However, the limits of these methods are revealed. But Electronic Speckle Pattern Interferometry(ESPI) that uses Pulse Laser is noncontact, whole-field, real-time measuring method also dull to disturbance and can achieve test result in a very short time. It has various strong point in spot application, swift establishment, and dynamic conduct analysis for the entire field of Laser illuminate. This author analyzed vibration characteristic of using the Pulse ESPI System, the diagnosis safety of bridges, to simplify the analysis of the dynamic conduct of a large construction.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2003년도 Proceedings of ACRS 2003 ISRS
• /
• pp.1046-1048
• /
• 2003

Recently, various researches in respect of the positioning technologies using satellites and the other sensors have made location-based services (LBS) more common and accurate. Consequently, concern about position information has been increasing. However, since these positioning systems only focus on user's position, it is difficult to know the user's attitude or detailed behaviors at the specific position. It is worthy to study on how to acquire such human attitude or behavior, because those information is useful to know the context of the user. In this paper, the sensor unit consisting of three dimensional accelerometer was attached to human body, and autonomously measured the perpendicular acceleration of ordinary human behaviors including activity modes such as walking, running, and transportation mode using transportation such as a train, a bus, and an elevator. Subsequently, using the classified measurement results, the method to identify the human activity modes was proposed.