• 대한전기학회논문지
• /
• 제44권4호
• /
• pp.447-452
• /
• 1995

In this paper a simple method of a position control for brushless DC motor is presented. For precise position control, a high performance torque controller is needed and a novel current control method is proposed. The current controller detects the uncommutating mode current for every 60.deg. (elec. angle) and controls it with PI controller. The current control loop includes the feedforward of back EMF and the feedforward of the neutral voltage between the neutral point of the inverter and the neutral point of the machine. In the position control, the acceleration pattern is calculated from the position reference. Then the speed trajectory is calculated from the acceleration pattern. The experimental results are presented to verify the proposed methods.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1997년도 한국자동제어학술회의논문집; 한국전력공사 서울연수원; 17-18 Oct. 1997
• /
• pp.289-292
• /
• 1997

In this paper, a continuous sliding mode controller for robot manipualator is proposed. The proposed scheme guarantees that the tracking error converges to zero maintaining the smoothness of the actual control signal. In order to estimate the acceleration data, a sliding mode observer is used, and the stability of the closed-loop system is shown.

• 반도체디스플레이기술학회지
• /
• 제12권1호
• /
• pp.53-59
• /
• 2013

Chip mounter which is used to pick chips from the pre-specified position and place them on the target location of PCB is an essential device in semiconductor and LCD industries. Quick and high precision positioning is the key technology needed to increase productivity of chip mounters. As increasing acceleration and deceleration of placing motion, structural vibration induced from inertial reactive force and flexibility of mounter structure becomes a serious problem degrading positioning accuracy. Motivated from these, this paper proposed a new control design algorithm which combines a mounter structure acceleration feedforward compensation and an extended sliding mode control for fine positioning and suppression of structural vibration, simultaneously. The feasibility of the proposed control design was verified along with some simulation results.

• 제어로봇시스템학회논문지
• /
• 제2권2호
• /
• pp.115-120
• /
• 1996

In this paper, a sliding mode controller which is characterized by high accuracy, fast response and robustness is applied to speed control of AC-SERVO motor. The control input is changed to the continuous one in the boundary layer to reduce the chattering phenomenon, and the boundary layer converges to zero when the state variables of system reach to steady state values. The integral compensator is added to reduce steady state error and to provide the continuous torque reference. The acceleration which is necessary for the sliding plane is estimated by an obsever. Sliding surface is included in control input to enhance the robustness and transient response without increasing sliding mode controller gain. The proposed controller is implemented by DSP(digital signal processor). The effectiveness of the proposed scheme is demonstrated through experimental works.

• 항공우주시스템공학회지
• /
• 제13권6호
• /
• pp.43-51
• /
• 2019

택싱모드 상태에서 노면의 가진으로 발생하는 기체 가속도는 조종사와 탑승객의 탑승감을 해치는 주 요인이다. 본 논문에서는 MR댐퍼 착륙장치의 탑승감을 향상시키기 위해 제어기법을 연구하였다. 제안된 제어기법은 Skyhook Control Type2 로 기존의 스카이훅 제어와는 달리 추가적으로 상부질량가속도를 피드백 받아 제어력을 구성한다. Skyhook Control Type2는 상부질량의 속도와 가속도를 모두 고려하기 때문에 상부질량속도만을 고려하는 스카이훅 기법의 제어한계를 개선하는 효과가 있다. 시뮬레이션을 위해 범퍼형태의 노면을 활주노면으로 선정하였으며, 리커다인(RecurDyn)으로 구성한 착륙장치 모델과 시뮬링크(Simulink)로 설계한 제어기를 연동해석 하였다. 시뮬레이션을 통해, 상부질량가속도의 RMS값과 최대값을 활주속도 및 제어기법에 따라 비교 분석하여 Skyhook Control Type2에 대한 제어효과를 검증하였다.

• 한국유체기계학회 논문집
• /
• 제16권6호
• /
• pp.5-11
• /
• 2013

Torque control methods of wind turbine are mainly classified into two methods: torque-mode and speed-mode methods. The traditional torque-mode method, in which generator torque proportional to square of generator speed is determined, has been chosen in many wind turbines but its response is slower as they are larger in multi-MW size. Torque control methods based on both speed-mode and torque-mode can be used to make response of wind turbine faster. In this paper, two torque control methods based on the traditional torque-mode method are applied to a 2.75 MW wind turbine. It is shown through some simulation results for real turbulence wind speeds that torque control method based on torque-mode has the merit of reducing fluctuations of generated power than PI controller based on speed-mode.

• International Journal of Automotive Technology
• /
• 제1권1호
• /
• pp.48-55
• /
• 2000

Two major roles of the traction control system (TCS) are to guarantee the acceleration performance and directional stability even in extreme road conditions, under which average drivers may not control the car properly. Commercial TCSs use experiential methods such as lookup table and gain-scheduling to achieve proper performance under various road and vehicle conditions. This paper proposes a new slip controller which uses the brake and the throttle actuator simultaneously. To avoid measurement problems and to get a simple structure, the brake controller and the throttle controller are designed using Lyapunov redesign method and multiple sliding mode control respectively. Through the hybrid use of brake and throttle controllers, the vehicle is insensitive to the variation of the vehicle mass, brake gain and road condition and can achieve the required acceleration performance. The proposed method is validated with simulations based on 15 DOF passenger car model.

• Advances in aircraft and spacecraft science
• /
• 제10권1호
• /
• pp.1-18
• /
• 2023

This paper investigates the integrated control of an air-breathing hypersonic vehicle considering the safety of propulsion system under acceleration. First, the vehicle/engine coupling model that contains a control-oriented vehicle model and a quasi-one-dimensional dual-mode scramjet model is established. Next, the coupling process of the integrated control system is introduced in detail. Based on the coupling model, the integrated control framework is studied and an integrated control system including acceleration command generator, vehicle attitude control loop and engine multivariable control loop is discussed. Then, the effectiveness and superiority of the integrated control system are verified through the comparison of normal case and limiting case of an air-breathing hypersonic scramjet coupling model. Finally, the main results show that under normal acceleration case and limiting acceleration case, the integrated control system can track the altitude and speed of the vehicle extremely well and adjust the angle deflection of elevator to offset the thrust moment to maintain the attitude stability of the vehicle, while assigning the two-stage fuel equivalent ratio to meet the thrust performance and safety margin of the engine. Meanwhile, the high-acceleration requirement of the air-breathing hypersonic vehicle makes the propulsion system operating closer to the extreme dangerous conditions. The above contents demonstrate that considering the propulsion system safety will make integrated control system more real and meaningful.

• International Journal of Aeronautical and Space Sciences
• /
• 제15권3호
• /
• pp.281-292
• /
• 2014

We propose a novel cooperative guidance law design method based on the finite time disturbance observer (FTDO) for multiple near space interceptors (NSIs) with impact time control. Initially, we construct a cooperative guidance model with head pursuit, and employ the FTDO to estimate the system disturbance caused by target maneuvering. We subsequently separate the cooperative guidance process into two stages, and develop the normal acceleration command based on the super-twisting algorithm (STA) and disturbance estimated value, to ensure the convergence of the relative distance. Then, we also design the acceleration command along the line-of-sight (LOS), based on the nonsingular fast terminal sliding mode (NFTSM) control, to ensure that all the NSIs simultaneously hit the target. Furthermore, we prove the stability of the closed-loop guidance system, based on the Lyapunov theory. Finally, our simulation results of a three-to-one interception scenario show that the proposed cooperative guidance scheme makes all the NSIs hit the target at the same time.

• 한국정밀공학회지
• /
• 제17권11호
• /
• pp.101-107
• /
• 2000

A design of the global optimal sliding mode control is presented to control the second order uncertain time varying system with torque limit. With specified ranges of parametric uncertainties and torque limit, the minimum arrival time to reference inputs can be calculated. The proposed control scheme is applied to the motor system carrying loads. The merit of the proposed control scheme is that the arriving time at the reference input, which is the revolution angle, and the maximum allowable acceleration are expressed in a closed form solution. The superior performance of the proposed control scheme is validated by the computer simulation and experiments comparing with other sliding mode controllers.