• Journal of Electrical Engineering and Technology
• /
• v.12 no.3
• /
• pp.1156-1165
• /
• 2017

A high performance interleaved bridgeless boost power factor correction (PFC) rectifier operating under the critical current conduction mode (CrM) is proposed in this paper to improve the efficiency and system performance of various applications, such as nano-grid systems. By combining the interleaved technique with the bridgeless topology, the circuit contains two independent branches without rectifier diodes. The branches operate in interleaved mode for each respective half-line period. Moreover, when operating in CrM, all the power switches take on soft-switching, thereby reducing switching losses and raising system efficiency. In addition, the input current flows through a minimum amount of power devices. By employing a commercial PFC controller, an effective control scheme is used for the proposed circuit. The operating principle of the proposed circuit is presented, and the design considerations are also demonstrated. Simulations and experiments have been carried out to evaluate theoretical analysis and feasibility of the proposed circuit.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.8
• /
• pp.54-63
• /
• 2007

This paper is proposed a novel method that computed approximately maximum power of photovoltaic system and solar tracking method. Proposed novel is linear reoriented coordinates method(LRCM), this paper is proposed new mathematical dynamic model using LRMC and DC dynamic equation. LRCM has the advantage that is decreased calculating time, decides optimal voltage and maximum power that generates continually. Furthermore solar tracking method is improved over 50[%] photovoltaic efficiency than fixed method. This paper is proposed MPPT using LRCM and solar tracking method using program method that is adequate domestic conditions, prove verify of proposed method through experiment.

• Journal of the Korean Solar Energy Society
• /
• v.27 no.2
• /
• pp.53-59
• /
• 2007

Knowledge of the solar radiation components are essential for modeling many solar photovoltaic systems. This is particularly the case for applications that concentrate the incident energy to attain high photo-dynamic efficiency achievable only at the higher intensities. In order to estimate the performance of concentrating PV systems, it is necessary to know the intensity of the beam radiation, as only this component can be concentrated. The Korea Institute of Energy Research(KIER) has began collecting solar radiation component data since August, 1996. KIER's component data will be extensively used by concentrating PV system users or designers as well as by research institutes.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2017.11a
• /
• pp.1241-1243
• /
• 2017

As the era of the fourth industrial revolution, renewable energy has been highlighted instead of fossil energy resource. Solar energy is constantly being developed in renewable energy, but energy gathering methods are not yet effective. In this paper, we study an efficient monitoring module for photovoltaic system for better performance of light sensor based solar tracking photovoltaic system with real time manner.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.12
• /
• pp.2103-2108
• /
• 2016

Energy saving is as important as developments of green energy and alternative energy. This paper describes design of hybrid type streetlight for railway station with renewable energy as photovoltaic, wind, secondary battery. In designing hybrid type streetlight for railway station, generation energy with renewable energy and reliability is strongly needed to meet the demand of railway station. In order to achieve the high performance of a streetlight, photovoltaic, wind and secondary battery system, PV tracker, monitoring and GUI system with logging function are designed. To verify of performance of hybrid type streetlight for railway station, we have demonstration test to get of generation energy and flow of energy and the results are present in this paper.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.10
• /
• pp.229-235
• /
• 2019

A floating photovoltaic generation system is a new concept that combines existing photovoltaic generation technology with floating technology. This is installed in the water not on conventional land and a building. The system is designed as a unit module type that can be connected to other modules according to the power generation capacity, thereby forming a large-scale power generation facility. As a renewable energy source, it is composed of a floating structure, mooring device, photovoltaic power generation facility, and underwater cable. Because this system is installed outdoors, the effect of the wind load on the structure is very large. In this study, the wind loads most affected on the floating photovoltaic generation structure were obtained by computational fluid dynamic analysis. The flow characteristics and wind loads were analyzed for a range of wind orientations and angles of inclination. The analysis showed the position and magnitude of the maximum wind load to the wind direction and the flow characteristics around the solar panel and floating system. The wind load increased with increasing angle of inclination of the panel to the ground.

• Journal of Cadastre & Land InformatiX
• /
• v.49 no.1
• /
• pp.17-27
• /
• 2019

In this study, we conducted a study to predict the photovoltaic power by constructing the sensor based meteorological data observation system and the accurate terrain data obtained by using LiDAR surveying. The average sunshine hours in 2018 is 4.53 hours and the photovoltaic power is 2,305 MWh. In order to analyze the effect of photovoltaic power on the installation angle of solar modules, we installed module installation angle at $10^{\circ}$ intervals. As a result, the generation time was 4.24 hours at the module arrangement angle of $30^{\circ}$, and the daily power generation and the monthly power generation were the highest, 3.37 MWh and 102.47 MWh, respectively. Therefore, when the module arrangement angle is set to $30^{\circ}$, the generation efficiency is increased by about 4.8% compared with the module angle of $50^{\circ}$. As a result of analyzing the influence of the seasonal photovoltaic power by the installation angle of the solar module, it was found that the photovoltaic power was high in the range of $40^{\circ}{\sim}50^{\circ}$, where the module angle was large from November to February when the weather was cold. From March to October, it was found that the photovoltaic power amount is $10^{\circ}{\sim}30^{\circ}$ with small module angle.

• Journal of Electrical Engineering and Technology
• /
• v.5 no.4
• /
• pp.606-613
• /
• 2010

This paper proposes a novel current-based maximum power point tracking (CMPPT) method for a single-phase photovoltaic power conditioning system (PV PCS) by using a modified incremental conductance method. The CMPPT method simplifies the entire control structure of the power conditioning system and uses an inherent current source characteristic of solar cell arrays. Therefore, it exhibits robust and fast response under a rapidly changing environmental condition. Digital phase locked loop technique using an all-pass filter is also introduced to detect the phase of grid voltage, as well as the peak voltage. Controllers of dc/dc boost converter, dc-link voltage, and dc/ac inverter are designed for coordinated operation. Furthermore, a current control using a pseudo synchronous d-q transformation is employed for grid current control with unity power factor. A 3 kW prototype PV PCS is built, and its experimental results are given to verify the effectiveness of the proposed control schemes.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.25 no.4
• /
• pp.311-318
• /
• 2020

A photovoltaic (PV) system uses an AC module integrated converter (MIC) to operate PV cells at a maximum power point (MPP) and for high efficiency. The MPP of a PV cell varies depending on partial shading conditions, and loss occurs differently according to the configuration method of the PV-MIC. Therefore, this study compares the losses of passive components and power semiconductors according to the partial shading conditions of the PV module. Theoretical loss analysis is performed using parameters for the datasheet and PSIM simulation results. Analysis results verify that the one-stage PV-MIC demonstrates high efficiency.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.2
• /
• pp.272-276
• /
• 2010

Renewable energy sources are considered to be environment-friendly alternatives those are increasingly introduced in the power systems. Microgrid is one of the systems in which renewable sources have a main role as a energy suppliers. Decision of constitution rates of renewable energy sources is very important for the economical and stable operation of microgird systems. In this paper, we present a method to assess an optimal constitution rate of renewable sources especially of windturbine and photovoltaic systems.