• Journal of the Korean Solar Energy Society
• /
• v.35 no.6
• /
• pp.51-60
• /
• 2015

In statutes on the promotion of distribution of new and renewable energy, which were revised in 2014, daylight system and fuel cell were added in addition to existing new and renewable energy sources. This study, therefore, aimed at setting up targets for the introduction of daylight system and analyzing the installation rate of new and renewable energy which can be provided by daylight system for the aggressive use of daylight system, thereby deducting the optimal combination ratio with other new and renewable energy sources. The results of the study are as follows. First, when a prism-shaped daylight system was installed to a round indoor gymnasium among domestic indoor gymnasiums, out of a supply obligations allotment rate of 15% of new and renewable energy, the rate of daylight system was basically set at 2.5%. Second, therefore, with daylight system coming first, the lacked supply obligations rate was taken up by solar photovoltaic, solar heat and geothermal heat. In addition, using the KRESS Program, economic, technical, environmental and complexity evaluations for the upper 5% was made, deducting the optimal ratio of the system. The results produced the following optimal combination ratios: solar photovoltaic (83.3%) in economic evaluation, solar heat (8.3%) and geothermal heat (75%) in technical evaluation, solar photovoltaic (83.3%) in environmental evaluation, and solar photovoltaic (83.3%, the same as in economic evaluation) in complexity evaluation.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.6
• /
• pp.563-569
• /
• 2002

This paper proposes an inverter for the grid-connected photovoltaic system based on the transformer-less inverter. This system consists of a high frequency DC-DC converter, high frequency transformer, diode bridge rectifiers, a DC filter, a low frequency inverter, and an AC filter. The 20kHz switched high frequency converter is used to generate bipolar PWM pulse, and the high frequency transformer transforms its voltage twice, which is subsequently rectified by diode bridge rectifiers for a full-wave rectified 60 Hz sine wave power output. Even though the high frequency link system needs more power semiconductors, a reduced size, light weight, and saved parts cost make this system more comparative than other power conditioning systems due to elimination of 60Hz transformer.

• Current Photovoltaic Research
• /
• v.9 no.2
• /
• pp.45-50
• /
• 2021

Agrovoltaic system is a concept that combines agriculture and photovoltaic (PV) system by applying a PV system to the upper part of farmland. In this study, we developed a folding drive system for an agrophotovoltaic (agroPV) module (150 Wp/4×9 cell) exclusively for pear farming with 10 kW capacity. The system was installed in 2018, and the growth characteristics and quantity of pears under the agroPV folding system have been investigated for 2 years. We found that thare is no differences of the characteristics of pears grown under the agroPV system compared to the pears grown without the system (control) except the percutaneous color L of pear. However, the weight and sugar content of the pear grown under the agroPV system were decreased by 4.5% and 1.3°Bx compared to that of the control, respectively. We assume that this is mainly due to the influenced of the delay in flowering as upper PV module block some of sunlight. However, interestingly, when we deleyed the pear harvesting by 2 weeks, the weight of pears increased by 8.5% and they became nearly the sample as the control pears harvested 2 week earlier. In addition, we also found that the agroPV modules decrease the fall rate of pear when the typoon struck, also it mitigates cold damage by 38% during April by protecting from frost. In conclusion, it can be said that the agroPV system help to protect target crops from the environmental conditions and the quality of the crops are similar to the that of control.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.419-422
• /
• 1999

This paper deals with stand-alone Photovoltaic system(SPVS) with charger/discharge controller. Main power source of SPVS are generally solar cel and battery. Therefore SPVS can be classified into variable types in accordance with connection type between battery and solar cell. SPVS with charger/discharge controller which can operate solar cell a maximum power point is suggested and designed with instantaneous controller. And system operating characteristics are verified by experiment with a laboratory prototype in this paper.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.7
• /
• pp.1039-1048
• /
• 2013

Generally, the buck converter controller was designed to control output voltage of the converter. However, design of the controller in photovoltaic power conditioning system is different from general design. the controller in photovoltaic power conditioning system controls input voltage of the converter(output voltage of the solar cell) for MPPT(Maximum Power Point Tracking). This paper proposes novel buck converter model which can control input voltage of the converter. We integrate this model with a model of solar cell. and linearize at the operating point(MPP). In addition, we determine whether or not suitable for the general linear controller design into small and large signal analysis.

• Journal of IKEEE
• /
• v.18 no.1
• /
• pp.159-164
• /
• 2014

This paper targets the development of micro-converter such as a power converter for photovoltaic module. In corresponding to the poor performance of centralized PV system under partial shading, the power converter for single PV module to maximize the energy harvest from PV module. The power converter is constantly tracking the maximum power point of photovoltaic system and increases energy output power. To minimize the quantity of devices and switchs, 320W solar micro-converter is developed using synchronous rectifier. From the basis of these results, through simulations and experiments were verified efficiency.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.5
• /
• pp.355-363
• /
• 2007

In this paper, the transformerless three-phase line-connected PV PCS (photovoltaic power conditioning system) is proposed. An improved P&O (perturb and observe) MPPT (maximum power point tracking) algorithm that prevents local maximum power point tracking is proposed. By controlling the three-phase line-connected voltage source inverter using outer DC-link voltage controller, inner current controller and microcontroller friendly simplified space vector modulation (SVM) method, a unity power factor is achieved. An algorithm is suggested to control the DC-link voltage faster and more correctly for the increase system stability and power factor. All algorithms and controllers are implemented on a single-chip microcontroller and the superiority of the proposed algorithms and controllers is proved by experiments.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.175-178
• /
• 2006

Solid-state dye-sensitized solar cells were fabricated using a polymer matrix in electrolyte in the purpose of the improvement of the durability in the dye-sensitized solar cell. In these dye-sensitized solar cells, the polymer electrolyte consisting of $I_2$, LiI, ionic liquid, ethylene carbonate/propylene carbonate and polymer matrix was casted onto $TiO_2$ electrode impregnated Ruthenium complex dye as a photosensitizer. Photovoltaic properties of solid-state dye-sensitized solar cells using polymer matrix (PMMA, PEG, or PAN) were investigated. Comparing photovoltaic effects of cells using hole conducting polymers (BE or 6P) instead of polymer matrix, we investigated the availability of the solid-state polymer electrolyte in dye-sensitized solar cells.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.11a
• /
• pp.561-565
• /
• 2006

The paper presents a method of assessing the adequate tapaclty of photovoltaic generation systems for public buildings based on analysis of load variation patterns of customers. When PV systems are installed for supplying power for the customer load, reverse power relay is required by the guideline to be installed at the point of common coupling with the power network. The suggested method analyzes daily, weekly and monthly load demand of the customer that Irishes PV system installation, and determines the appropriate rating of the PV system for preventing PV generation from exceeding the customer demand. This work is expected to support renewable energy dissemination projects of public organizations.

• Proceedings of the KIPE Conference
• /
• 2006.06a
• /
• pp.529-531
• /
• 2006

The Photovoltaic(PV) generation system is a promising source of energy for the future. Since the need for renewable energy has been increased, the research of PV generation system has also been progressed. The main subject of this paper is about making the more useful real-time monitoring program to get and save the data from photovoltaic generation system of 30kW grid-connected. Therefore, it uses LabView for this real-time monitoring program.