• Nuclear Engineering and Technology
• /
• v.30 no.1
• /
• pp.1-7
• /
• 1998

Effects of pH, bentonite and Portland cement on the leaching of the simulated waste glass were investigated. The simulated waste glass showed the low leach rate in the neutral pH region, while the leach rate in both acidic and alkaline regions increased. Addition of bentonite to the leachant enhanced the leaching of the waste glass. When the waste glass was leached at 72$^{\circ}C$ for 36 days in the ground water with gel state Na-bentonite, approximately 2.2${\mu}{\textrm}{m}$ of the surface was corroded out and the large amount of Ti, Nd, and Zr was observed on the surface. The amount of B leached from the simulated waste glass in the presence of domestic bentonite was about three times higher than that in the presence of Aldrich bentonite as well as Portland cement.

• Journal of the Korean Vacuum Society
• /
• v.15 no.3
• /
• pp.325-330
• /
• 2006

In order to verify the integrity of the first wall (FW) of the International Thermonuclear Experimental Reactor (ITER), the fabricated Cu/SS mock-up is tested in the JAEA Electron Beam Irradiation Test Stand (JEBIS). To fabricate the Cu/SS mock-up, CuCrZr and 316L authentic stainless steel (SS316L) are used for Cu alloy and steel, respectively The hot isostatic pressing (HIP) is used as a manufacturing method with a $1050^{\circ}C$ and 150 MPa. The high heat flux (HHF) test is performed using an electron beam with a heat flux of $5MW/m^2$ and a cycle of 15-sec on time and 30-sec off time. The temperature measurement in the HHF test shows good agreement with the results obtained from ANSYS code analysis, which is used for determining the HHF test conditions.

• Korean Journal of Materials Research
• /
• v.29 no.8
• /
• pp.469-476
• /
• 2019

A lead-free bulk ceramic having a chemical formula $Ba_{0.8}Ca_{0.2}(Ti_{0.8}Zr_{0.1}Ce_{0.1})O_3$ (further termed as BCTZCO) is synthesized using mixed oxide route. The structural, dielectric, impedance, and conductivity properties, as well as the modulus of the synthesized sample are discussed in the present work. Analysis of X-ray diffraction data obtained at room temperature reveals the existence of some impurity phases. The natural surface morphology shows close packing of grains with few voids. Attempts have been made to study the (a) effect of microstructures containing grains, grain boundaries, and electrodes on impedance and capacitive characteristics, (b) relationship between properties and crystal structure, and (c) nature of the relaxation mechanism of the prepared samples. The relationship between the structure and physical properties is established. The frequency and temperature dependence of the dielectric properties reveal that this complex system has a high dielectric constant and low tangent loss. An analysis of impedance and related parameters illuminates the contributions of grains. The activation energy is determined for only the high temperature region in the temperature dependent AC conductivity graph. Deviation from the Debye behavior is seen in the Nyquist plot at different temperatures. The relaxation mechanism and the electrical transport properties in the sample are investigated with the help of various spectroscopic (i.e., dielectric, modulus, and impedance) techniques. This lead free sample will serve as a base for device engineering.

• Journal of the Korean Electrochemical Society
• /
• v.1 no.1
• /
• pp.45-51
• /
• 1998

[ $AB_2-type$ ] alloy, one kind of hydrogen storage alloys used as an anode of Ni-MH batteries, has large discharge capacity but has remaining problems regarding initial activation, cycle life and self-discharge. This study investigates the effects of Cr-addition and fluorination after La-addition on $Zr_{0.7}Ti_{0.3}V_{0.4}Mn_{0.4}Ni_{1.2}$, composition $AB_2-type$ alloy. EPMA and SEM surface analysis techniques were used and the crystal structure was characterized by XRD analysis. In addition, electrodes were fabricated out of the alloys and characterized by constant current cycling test, electrochemical impedance spectroscopy and potentiodynamic polarization. Cr-addition was found to be effective to cycle life and self-discharge but ineffective to initial activation due to formation of stable oxide film on surface. Fluorination after La-addition to the alloys improved initial activation remarkably due to formation of highly reactive particles on surface.

• Proceedings of the KIEE Conference
• /
• 1991.11a
• /
• pp.293-295
• /
• 1991

In this study, we investigated the possibilty that $Pb(Mg_{1/3}Nb_{2/3})O_3-PbTiO_3-PbZrO_3$ ceramics with strontium substitutions could be used for piezoelectric sounders. Piezoelectric buzzer is one of them. By partially substituting Sr for Ph, dielectric constants had values greater than 2000, the value proper piezoelectric buzzer, piezoelectric constant($d_{31}$) had a maximum value, 298 $[10^{-12}C/N]$, at the Sr 5 mol % substitution. Sound level of piezoelectric buzzer had the highest value of 91 dB at the Sr 5 mol % substitution.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.6
• /
• pp.59-64
• /
• 2003

Recently, as people pay attention to the environmental pollution, the emissions of diesel engine have been a serious problem. We carried out the performance evaluation test of Diesel Oxidation Catalysts (DOC) for HSDI diesel engine equipped vehicles. The DOC, basically coated with Pt catalyst, was manufactured with various washcoat materials. It was found that CO conversion efficiency depends on temperature, but THC conversion efficiency is dominated by temperature and space velocity. The THC and CO conversion efficiencies of aged catalysts were increased with additions of $ZrO_2$ and zeolite B in the washcoat. We found that DOC performance changes with coating techniques, even through it has same washcoat materials. The DOC coated by high temperature washcoat coating technology showed good conversion efficiency than low temperature washcoat coated DOC.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2005.05a
• /
• pp.309-310
• /
• 2005

Some minor elements(Al, B, Ba, Ca, Cd, Co, Cr, Cu, Gd, Mg, Mn, Mo, Nd, Ni, P, Pb, Si, Sn, Sr, Ti, V, Yb, Zn and Zr) in iron compounds such as the S/G sludge of a power plant were separated from iron by anionic and cationic exchange methods. If a ICP-AES or AAS determination follows this method, minor elements of more than 2 or 20 ppm of Fe can be determined with an error less than 20% except Sn and Mo. Alkaline elements were excluded from this study since they can be easily recovered from an anionic exchange. Application to real sludge samples is ongoing.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.34-34
• /
• 2003

Piezoelectric or magnetostrictive materials, known as smart materials, have been researched widely for sensors or actuators in micro system technology. In our research, thick sol-gel lead zirconate titanate(Pb(Zr$\sub$1-x/Ti$\sub$x/)O$_3$) films were fabricated and their characteristics were investigated f3r angular rate sensor applications. The thickness of the PZT films is 1.5${\mu}$m, which is required by a vibration angular rate sensor for a good actuation and sensing. The remnant polarization of the PZT flms is 12.0 ${\mu}$C/$\textrm{cm}^2$. The electromechanical constants of PZT thin film showed the value of susceptance(B) of 4800${\mu}$ s at capacitance of 790pF. The PZT films were applied to the vibration angular rate sensor structure and the vibration of 1.78 ${\mu}$m in amplitude at the resonant frequency of 35.8㎑ was obtained by driving voltage of 5V$\sub$p-p/ of bulk piezoelectric materials with out of phase signal through voltage and inverting amplifier.

• Journal of Sensor Science and Technology
• /
• v.15 no.3
• /
• pp.168-172
• /
• 2006

Potentiometric $CO_{2}$ sensors were fabricated using a NASICON ($Na_{1+x}Zr_{2}Si_{X}P_{3-X}O_{12}$, 1.8 < x < 2.4) thick film and auxiliary layers. The powder of a precursor of NASICON with high purity was synthesized by a sol-gel method. By using the NASICON paste, an electrolyte was prepared on the alumina substrate by screen printing and then sintered at $1000^{\circ}C$ for 4 h. A series of $Na_{2}CO_{3}-CaCO_{3}$ auxiliary phases were deposited on the Pt sensing electrode. The electromotive force (emf) values were linearly dependent on the logarithm of $CO_{2}$ concentration in the range between 1,000 and 10,000 ppm. The device attached with $Na_{2}CO_{3}-CaCO_{3}$ (1:2 in mol.%) showed good sensing properties in the low temperatures.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.339-342
• /
• 1998

Ferroelectric L $a_2$ $Ti_2$ $O_{7}$(LTO) thin films were prepared by chemical solution deposition processes. Acetylacetone was used as chelating agent and nitric acid was added in the stock solution to control hydrolysis and condensation reaction rate. The LTO thin films were spin-coated on Pt/Ti/ $SiO_2$/(100)Si and Pt/Zr $O_2$/ $SiO_2$/(100)Si substrates. After multiple coating, dried thin films were heat-treated for decomposition of residual organics and crystallization. The role of acetylacetone in Ti iso-propoxide stabilization by possibly substituting $O^{i}$Pr ligand was studied by H-NMR. B site-rich impurity phase, i.e. L $a_4$ $Ti_{9}$ $O_{24}$, was found after annealing, where its appearance was dependent on process temperature indicating the possible reaction with substrate. Dielectric and other relevant electrical properties were measured and the results were compared between modified sol-gel and MOD processes.s.s.