• Fire Science and Engineering
• /
• v.9 no.2
• /
• pp.29-36
• /
• 1995

In this study, the effect of Mn $O_2$ additive on the electrical characteristics of PZN-PSS-PZT Pyroelectric materials for the fire detactor was studies. PZT ceramics used this experimental is 4 composite system $[$Pb(Z $n_{1}$3/ N $b_{2}$3/) $O_3$＋Pb(S $n_{1}$3/ S $b_{2}$3/) $O_3$＋PbTi $O_3$＋PbZr $O_3$$]$The dielectric constants and dissipation factors decreases as to Mn $O_2$ concentration increases. At the Mn $O_2$ 0.5($\omega$t%), Pyroelectric coefficient shows 8(10$^{-8C}$$\textrm{cm}^2$$^{\circ}C$) which have the highst value among other additive contents. It is found that output voltage shows maximum peck at Mn $O_2$0.7($\omega$t％) is associated with the higher pyroelectric coefficient and Lowered dielectric constant.t.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.5
• /
• pp.808-815
• /
• 2008

The composites were fabricated 61[vol.%] ${\beta}$-SiC and 39[vol.%] $TiB_2$ powders with the liquid forming additives of 8, 12, 16[wt%] $Al_2O_3+Y_2O_3$ as a sintering aid by pressureless annealing at 1650[$^{\circ}C$] for 4 hours. The present study investigated the influence of the content of $Al_2O_3+Y_2O_3$ sintering additives on the microstructure, mechanical and electrical properties of the pressureless annealed SiC-$TiB_2$ electroconductive ceramic composites. Reactions between SiC and transition metal $TiB_2$ were not observed in the microstructure and the phase analysis of the pressureless annealed SiC-$TiB_2$ electroconductive ceramic composites. Phase analysis of SiC-$TiB_2$ composites by XRD revealed mostly of ${\alpha}$-SiC(6H), ${\beta}$-SiC(3C), $TiB_2$, and In Situ YAG($Al_2Y_3O_{12}$). The relative density of SiC-$TiB_2$ composites was lowered due to gaseous products of the result of reaction between SiC and $Al_2O_3+Y_2O_3$. There is another reason which pressureless annealed temperature 1650[$^{\circ}C$] is lower $300{\sim}450[^{\circ}C]$ than applied pressure sintering temperature $1950{\sim}2100[^{\circ}C]$. The relative density, the flexural strength, the Young's modulus and the Vicker's hardness showed the highest value of 82.29[%], 189.5[Mpa], 54.60[Gpa] and 2.84[Gpa] for SiC-$TiB_2$ composites added with 16[wt%] $Al_2O_3+Y_2O_3$ additives at room temperature. Abnormal grain growth takes place during phase transformation from ${\beta}$-SiC into ${\alpha}$-SiC was correlated with In Situ YAG phase by reaction between $Al_2O_3$ and $Y_2O_3$ additive during sintering. The electrical resistivity showed the lowest value of 0.0117[${\Omega}{\cdot}cm$] for 16[wt%] $Al_2O_3+Y_2O_3$ additives at 25[$^{\circ}C$]. The electrical resistivity was all negative temperature coefficient resistance (NTCR) in the temperature ranges from $25^{\circ}C$ to 700[$^{\circ}C$]. The resistance temperature coefficient of composite showed the lowest value of $-2.3{\times}10^{-3}[^{\circ}C]^{-1}$ for 16[wt%] additives in the temperature ranges from 25[$^{\circ}C$] to 100[$^{\circ}C$].

• Electrical & Electronic Materials
• /
• v.6 no.5
• /
• pp.436-445
• /
• 1993

2단계하소법에 의해 낮은 하소온도에서 미세하고도 균일한 PZT분말을 합성하였다. 우선 Zr $O_{2}$와 Ti $O_{2}$ 혼합분말을 1차하소하여 (Z $r_{0.53}$ $Ti_{0.47}$) $O_{3}$(ZTO) 분말을 합성하고 이 ZTO 고용분말에 PbO와 N $b_{2}$ $O_{5}$을 혼합한 후 650-800.deg.C에서 2시간 하소하여 PZT 분말을 합성하였는데 얻어진 분말은 고상반응법에 비해 미세할 뿐만 아니라 XRD 분석결과 710.deg.C의 낮은 하소온도에서도 PZT 단일상을 나타내었다. 2단계하소법에 의해 하소온도를 낮출 수 있는 주된 이유로는 고상반응법에서는 중간생성물인 PbTi $O_{3}$상의 생성이 수반됨으로 850.deg.C 이상 되어야만 안전한 PZT가 생성될 수 있는 점을 들 수 있다. 또 2단계하소법에 의하면 950.deg.C이하의 낮은 소결온도에서도 치밀화가 미루어지는 소결이 가능함을 알 수 있었는데 이와같이 소결온도를 낮출 수 있는 것은 고상반응법에 비해 미세한 PZT 분말을 사용하였기 때문이라 풀이된다.이된다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.2
• /
• pp.191-196
• /
• 2023

In this paper, for the application of ultrasonic cleaners for cleaning dentures and transparent braces, Pb(Mn_1/3Nb_2/3)O₃-Pb(Ni_1/3 Nb_2/3)O₃-Pb(Zr,Ti)O₃ [PMN-PNN-PZT] system ceramics were manufactured and their dielectric and piezoelectric properties were investigated. Overall the best properties suitable for the device applications such as ultrasonic cleaner were obtained from the ceramics sintered at 920℃: bulk density of 7.8 g/cm³, the dielectric constant (ε_r) of 1,689, piezoelectric charge constant (d₃₃) of 433 pC/N, planar electromechanical coupling factor (k_p) of 0.64, mechanical quality factor (Qm) of 835, S₁₁^E of 13.37 (10^-12 N/m²), and Curie temperature of 315℃ By using the physical properties of this composition, the ultrasonic cleaner was designed and simulated using the commercial ATILA software. For the three-layered ceramics with the dimension of 25 mm × 25 mm × 2.5mm, an excellent displacement of 8.998 10^-3 m) and the sound pressure of 147.68 dB were recorded.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.12
• /
• pp.3083-3093
• /
• 1993

Friction and wear at ceramic coated surfaces of aluminum alloy were experimentally studied using a Ring-on-Block wear test machine. Ceramic materials coated on aluminum alloy surfaces were WC, CrC, $Al_{2}O_{3}$ by a plasma spray; and $Al_{2}O_{3}$,$Al_{2}SiO_{5}$, $Na_{2}B_{4}O_{7}$,$Na_{4}P_{2}O_{7}$, and $Al_{2}O_{3}-ZrO_{2}$ composite coating by an Anodic Spark Depositon. They were tested under the sliding wet contact and compared with aluminum alloys and steels. Test results showed that ceramic coated surfaces, in general, have better anti-wear property than those of aluminum alloys due to increase in the surface hardness ; however, they also showed higher coefficients of friction and changes in wear mechanisms, resulting in brittle fractures.

• Journal of Korea Foundry Society
• /
• v.30 no.4
• /
• pp.147-150
• /
• 2010

An eco-friendly production technique of Al-8.6Ti-0.025C refiner was developed by melting a Al-Ti master alloy in a graphite crucible, in which the potential nucleation site, TiC effectively formed by the spontaneous in-situ reaction between excessive Ti and carbon from graphite crucible. The A3003 alloy refined by the Al-8.6Ti-0.025C showed effectively refined macrostructure and enhanced mechanical properties comparable to the commercial Al-Ti-B refiner. The effective refinement was achieved in a shorter compare to the melt-treating time commercial Al-Ti-B refiner.

• Journal of the Korean institute of surface engineering
• /
• v.30 no.4
• /
• pp.285-297
• /
• 1997

Finned segment, with which are lined inner wall of the turbine combustors, are subject to severe degradation when they are exposed to a hostile environmment at elevated temperature. To protect the finned segment from this environment and to maintain good mechanical properties of components at high temperature, they are preferred to be coated. The most governing factor for the durability of coatings used in the high temperature is the microstructure of coatings; these are splat from, distibution of microcacks, size and distribution of pores, thickness of coating layer, adhesion between coating layer, and oxidation of band coating. In this study, based on the evaluation of the imported finned segment, new finned segment segment was manufactured with optimum plasma spraying parameters, and their properties were examined. Using $ZrO_2(8wt$Y_2O_3)$,/TEX> powder for ceramic coating and 67Ni-22Cr-10Al-0.5Y mixing powder for bond coating, thickness of ceramic and bond coating layer were varied in order to find optimum condition, the results showed that B2T4(bond coating : 100~250$\mu\textrm{m}$, ceramic coating : 250~300$\mu\textrm{m}$) was the best among the specimens tested. Compared to the imported finned segment, B2T4 has better bond strength, hardness, and isothermal and cyclic oxidation resistance.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05c
• /
• pp.238-243
• /
• 1996

현재 상용 공급되고 있는 4종의 경수로 핵연료 피복관에 대해 노외 부식특성 시험을 수행하여 그 특성을 비교하였다. 이중 3종의 피복관은 제조공정을 달리하여 제조된 low tin Zircaloy-4 (피복관 A, B, C)이며, 1종은 Nb이 첨가된 Zr 합금 (피복관 D)이었다. 증류수내 Li 함량을 2.2 ppm, 30 ppm, 220 ppm으로 변화시키며 부식시험을 수행한 결과 최종 pilgering시 낮은 Q 인자와 높은 열처리 온도로 제조된 피복관 A의 내부식성이 대체로 우수하였으며, 220 ppm Li 수용액에서는 Nb이 첨가된 피복관의 내부식성이 매우 우수한 것으로 나타났다. Li 첨가의 영향을 보면 2.2 ppm Li 첨가시에는 증류수와 거의 동일한 부식거동을 나타내고 있으나 30 ppm Li 첨가시에는 부식이 가속되고 있었으며, 220 ppm Li으로 Li 함량이 크게 증가하였을 때 부식속도도 크게 증가하였다. 수소흡수율은 피복관 A에서 가장 높았으며, 피복관 D가 가장 낮은 값을 나타내었다.

• Journal of the Korean Chemical Society
• /
• v.55 no.3
• /
• pp.444-453
• /
• 2011

VO(II), ZrO(II), Hf(IV), $UO_2$(II), Sn(II), V(V)$O_3$, Ru(III), Cd(II), Ho(III) and Yb(III) complexes of N'-(2-hydroxybenzyl)-2-(phenylamino)acetohydrazide ($H_2L^1$, 1) and N'-((3-hydroxy-naphthalen-2-yl)methylene)-2-(phenylamino)-acetohydrazide ($H_2L^2$, 13) have been synthesized and characterized by elemental analyses, $^1H$ NMR, IR, UV-Vis, conductance, thermal analyses (DTA and TG). The spectral data showed that the ligands behave as neutral bidentate, monobasic bidentate, monobasic tridentate or bibasic tridentate ligand bonded to the metal ions through the azomethine nitrogen atoms, phenolic hydroxyl group in protonated or deprotonated form and enolic or ketonic carbonyl group. The ligands and their metal complexes exhibit higher antifungal and antibacterial inhibitory effects than parent ligands and the solution of metal ions. Most of metal complexes exhibit higher antifungal activity than standard antifungal drug (amphotricene B). It is also clear that the ligands and their metal complexes have higher antifungal activity than antibacterial activity.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.93-96
• /
• 2003

Recently, various bulk metallic glasses (BMG's) haying good mechanical and chemical properties were developed. BMG's can easily be deformed in the supercooled liquid region, via viscous flow mechanism. In our previous work, we evaluated the deformation behavior and some other basic properties of Z $r_{41.2}$ $Ti_{13.8}$C $u_{12.5}$N $i_{10}$B $e_{22.5}$ alloy. In this study, we investigated the micro forming of Z $r_{41.2}$ $Ti_{13.8}$C $u_{12.5}$N $i_{10}$B $e_{22.5}$ alloy. The process condition was chosen based on the viscosity data from TMA, and superalloy and Si wafer with micro patterns on the surface were used as forming die. The alloy showed good replication of the patterns. However, some stripe patterns, resembling scratches, appeared on the deformed alloy surface. These scratches can be reduced or eliminated by polishing before forming.ing.ore forming.ing.