• Electrical & Electronic Materials
• /
• v.10 no.2
• /
• pp.150-155
• /
• 1997

Powder type electroluminescent device(P-ELD) in this study was prepared by printing method. P-ELDs were basically composed of phosphor, insulator and transparent conducting layer. The phosphor powder was prepared by sintering the mixture of ZnS as a host, Cu as an activator, and NaCl as a flux for co-activator and enhancement of growth of the phosphor particles. The phosphor layer was made by printing the paste of the cyanoethylpullan as a binder and the ZnS system phosphor powder. In order to evaluate the luminescence characteristics of ZnS P-ELD, applied voltage - luminance(V-L), frequency-luminance(f-L), and relative luminance spectra(L- .lambda.) characteristics were measured. The experimental results show that luminance increased with increasing the applied voltage and frequency. It can be explained in terms of the potential barrier formed between ZnS and CuS. Two emission peaks in luminance-wavelength spectra measured at applied voltage of 100 $V_{rms}$ were observed at 500nm as a primary peak and 460nm as a secondary peak, respectively.y.

• Applied Chemistry for Engineering
• /
• v.9 no.3
• /
• pp.394-398
• /
• 1998

An optimum synthetic condition was studied for the MCS used as a silicone monomer. The contact mixture was made from the four component catalyst system($CuCl/ZnCl_2/Sn/Cd$) and silicon particles. The contact mass was used for a series of experiments with methyl chloride, which were designed and done to explore the optimum condition for MCS synthesis by an experimental design method. The optimum temperature and MeCl flow rate, which were obtained using 50g contact mass at 60rpm and 1 atm, were in the range of $300-305^{\circ}C$ and of 70-80ccm. Also a continuous run was performed to confirm the conditions. The results showed that the average reaction rate and selectivity were 170(g-MCS/hr.kg-Si) and 0.05 respectively at 67% conversion of MeCl and 92% silicon utilization rate. Also the parameters of overall reaction rate equation and a total pressure were estimated on the basis of the results of the continuous run.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.306-309
• /
• 1989

This paper describes the Manufacturing process and electrical properties of ac thick film electroluminescent lamps which made of the mixture of ZnS:Cu,Cl phosphor powder and polymer binding materials. The phosphor layer is sandwiched between two electrodes, one of which is transparent, and is supported by a substrate. The substrate may be glass or flexible plastic or it may be metallic. In this study we manufactured suspend layer which consists of ZnS:Cu,Cl powder suspended in a NBR. As yet our results are behind other commercial product in electrical properties and brightness. However they can be improved by selection of appropriate polymer binding materials, development of blending technology.

• Economic and Environmental Geology
• /
• v.27 no.2
• /
• pp.161-170
• /
• 1994

Jindong Granites are plotted mainly in the region of granodiorite~diorite of the Streckeisen's diagram, while Yucheon-Eonyang Granites and Onjonri Granites in the region of monzo-granite and monzo-granite~granodiorite, respectively. Jindong Granites show a differenciation trend of calc-alkaline magma, and its magmatic evolution from intermediate to acidic rocks, which might form mineralizing solution, is consistant with the general path of the Cretaceous granitic rocks including Yucheon-Eonyang Granites and Onjongri Granites. The differenciation index (D.I.) is 35~80 for Jindong Granites, which is lower than 85~95 of Yucheon-Eonyang Granites and is partly overlapped by 67~84 of Onjongri Granites. There is clear difference in content of some major and trace elements between Jindong Granites of Cu province and the other granitic rocks of Pb-Zn and Mo provinces. Between these metallogenic provicnes, Cu content is high in Jindong Granites near Haman-Gunbuk mineralized zone, while Pb and Zn are relatively abundant in Yucheon-Eonyang Granites and Mo in Onjongri Granites. Therefore, Jindong Granites of the Cu province are distinguishable by chemical compositions and their related geochemical characteristics from the other Cretaceous granitic rocks of Pb-Zn and Mo provinces. However, the content of Cu and Cl in biotite is applicable to distinguish a productive phase from a barren phase of Jindong Granites, because Cu and Cl show a trend to be concentrated in biotite of Jindong Gratites in the Haman-Gunbuk mineralized zone.

• Journal of fish pathology
• /
• v.4 no.1
• /
• pp.31-39
• /
• 1991

Vibrio sp. S-1-2 was isolated from seawater in the Masan bay and its bacterial characteristics and bioaccumulation of $CdCl_2$ in the cell were investigated. As the result of microscopic and biochemical test, the S-1-2 strain was identified to Vibrio sp. and this strain can be tolerated even in 200 ppm $CdCl_2$ media, however its growth was inhibited. In 25 ppm $ZnCl_2$ media, the growth of Cd resistant Vibrio sp. S-1-2 was promoted at later stage of growth. The growth of Vibrio sp. S-1-2 was inhibited on 25 ppm $CuCl_2$ and $PbCl_2$ media and was not able to grow in 25 ppm $HgCl_2$ media at all. The uptake of cadium in the cells was increased exponentially with increasing concentration of $CdCl_2$ in media. But the uptake rate of cadmium was suddenly inhibited at 50 ppm $CdCl_2$ media. Optimal pH and NaCl concentration for bioaccumulation of $CdCl_2$ were 8-9 and 1-2%, respectively. In the case of pH, maximum dpm value was found at pH 7 after 96 hours culture and in the case of NaCl concentration, it was detected in 2% NaCl media after 36 hours culture.

• Economic and Environmental Geology
• /
• v.28 no.1
• /
• pp.9-17
• /
• 1995

The Kamkye Cu-Pb-Zn-Au-Ag deposits occur as quartz veins that filled fault-related fractures of NW system developed in the Cretaceous Gyeongsang basin. Three major stages of mineral deposition are recognized: (1) the stage I associated with wall rock alteration, such as sericite, chlorite, epidote and pyrite, (2) the early stage II of base-metal mineralization such as pyrite, hematite, and small amounts of sphalerite and chalcopyrite. and the middle to late stage II of Cu-As-Sb-Au-Ag-S mineralization, such as sphalerite, chalcopyrite, galena with tetrahedrite, tennantite, pearceite, Pb-Bi-Cu-S system, argentite and electrum. (3) the stage III of supergene mineralization, such as covellite, chalcocite and malachite. K-Ar dating of alteration sericite is a late Cretaceous ($74.0{\pm}1.6Ma$) and it may be associated with granitic activity of nearby biotite granite and quartz porphyry. Fluid inclusion data suggest a complex history of boiling, cooling and dilution of ore fluids. Stage II mineralization occurred at temperatures between 370 to $220^{\circ}C$ from fluids with salinities of 8.4 to 0.9 wt.% NaCl. Early stage II($320^{\circ}C$, 2.0 wt.% NaCl) may be boiled due to repeated fracturing which opened up the hydrothermal system to the land surface, and which resulted in a base-metal sulfide. Whilst the fractures were opened to the surface, mixing of middle-late stage II ore fluids with meteoric waters resulted in deposition of Cu-As-Sb-Au-Ag minerals from low temperature fluids(${\leq}290^{\circ}C$). Boiling of ore fluids may be occured at a pressure of 112 bar and a depth of 412 m. Equilibrium thermodynamic interpretation of sphalerite-tetraherite assemblages in middle stage II indicates that the ore-forming fluid had log fugacities of $S_2$ of -6.6~-9.4 atm.

• Analytical Science and Technology
• /
• v.13 no.2
• /
• pp.215-221
• /
• 2000

Analysis of fly ashes from the MSW incinerators was carried out using XRF, ICP-MS and ICP-AES. It was found that the major elements of fly ash were Ca, K, Na, Si, Al, S, Cl and O by the XRF analysis. The XRD spectra showed that the fly ashes were mainly consisted with the chlorides, hydroxides, carbonates and also oxides of former elements. For the determination of minor elements such as Zn, Pb, Cu, Cr, and Cd, we used ICP-AES and ICP-MS after microwave digestion and the results were compared with the result of XRF.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.68-68
• /
• 2010

Electroluminescence (EL) characteristics of green-emission ZnS:Cu,Cl-based ac-type inorganic powder electroluminescent structures were examined by inserting carbon nanotubes (CNTs) into or next to the dielectric layer. For the top-emission type EL structure, where the luminescent light was emitted from the top of the structure, was fabricated by assembling in order, a top electrode, an emitting layer, a dielectric layer, and a bottom electrode from the top. $BaTiO_3$ powder mixed with CNTs was used as a dielectric layer or CNTs were deposited between the bottom electrode and $BaTiO_3$ dielectric layer in order to improve the role of the dielectric layer in the structure. Luminance of an EL structure with CNTs inclusion was greatly enhanced possibly due to the high dielectric constant in the dielectric layer of $BaTiO_3$/CNTs, which is one of hot research topics utilizing nano-objects for intensifying dielectric constant and reducing dielectric loss at the same time. A variation on the CNTs themselves and their inclusion methods in the dielectric layer has been exhorted, and the underlying mechanism for the role of CNTs in the EL structure will be explained in the poster. In order to extend the flexibility of EL devices, EL devices were fabricated on the paper substrate and their performance was compared other EL devices on the plastic-based substrate.

• Korean Journal of Microbiology
• /
• v.20 no.3
• /
• pp.105-112
• /
• 1982

The strain of Aspergillus, 6368A, producing acid protease showing high activity was isolated from soil, as a result of wide research about mold group. This strain was identified as a species of Aspergillus tubingensis by the investigation of morphological characteristics. The change of the enzyme production under the various media and culture condition was also studied. The optimum pH and stability of crude acid protease are 2.5, 2.0~4.5 and the optimum temeprature and thermal inactivation waas shown $50^{\circ}C,\;55^{\circ}C$, respectively. From the result of the study on the effects of metal ions, it was found that $MnCl_2,\;CoCl_2,\;CuCl_2,\;SrCl_2,\;and\;NiCl_2$ slightly increased the enzyme activity, on the other hand $ZnCl_2,\;CaCl_2,\;MgCl_2,\;SLS,\;and\;KMnO_4$ decreased it.

• Clean Technology
• /
• v.6 no.1
• /
• pp.61-69
• /
• 2000

In this study, generation process and properties of inorganic industrial waste which can be used in cement industry were investigated. The scheme of recycling to use the selected waste as raw materials, mineralizer and flux, admixture and raw materials for special cement was decided and then various experiments were carried out. The experimental results were as follows ; In the use of industrial waste as raw materials, ferrous materials could be substituted by Cu-slag, Zn-slag, electric arc furnace or convertor furnace slag etc., and a siliceous material could be substituted by sand from cast-iron industry. By-products from sugar or fertilizer industry, which has $CaF_2$ as the main component, and jarosite from Zn refinery enabled clinker phases to be formed at lower temperature by $100{\sim}150^{\circ}C$. Adding Cu slag and STS sludge in proper proportion to cement improved properties of cement. Fly ash and limestone powder as admixture had the same effect on cement. As a raw material for special cement, aluminium waste sludge could be used in making ultra early strength cement, which had the compressive strength of $300kg/cm^2$ within 2hours. And two different ashes from municipal incinerator could be raw materials of the cement which was mainly composed of $C_3S$ and $C_{11}A_7{\cdot}CaCl_2$ as clinker phases.