• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.375-375
• /
• 2011

Cu(In1-xGax)Se2 (CIGS)박막증착법 중 금속 전구체의 셀렌화 공정법은 다른 제조 방법에 비해 대면적 생산에 유리하고, 비교적 공정 과정이 간단하다는 장점이 있다. 이 제조 방법은 금속 전구체를 만든 후에 셀렌화 공정을 하게 된다. 셀렌화 공정은 대부분 H2Se 가스를 사용하지만 유독성으로 사용하는데 주의해야 한다. 본 실험은 H2Se를 사용하지 않고 Se원료를 주입하기 위해 Se cracker를 사용했고 금속 전구체 증착과 셀렌화를 동시에 하는 반응성 스퍼터링 후 열처리 법을 이용하여 CIGS 박막을 증착 했다. CIGS의 박막의 Cu/[In+Ga], Ga/[In+Ga]비를 변화시켜 특성변화를 관찰했다. Cu/[In+Ga]비가 감소할수록 CIGS의 결정방향인 (112) 이 우세하게 발달했고 Ga/[In+Ga]비가 증가할수록 CIGS의 결정면 사이의 값이 작아지기 때문에 CIGS peak의 2-Theta 값이 증가하게 된다. CIGS 박막 태양전지의 구조는 Al/Ni/ITO/i-ZnO/CdS/CIGS/Mo/glass 제작했다. CIGS박막의 조성비가 Cu/[In+Ga]=0.84, Ga/[In+Ga]=0.24인 박막태양전지에서 개방전압 0.48 V, 단락전류밀도 33.54 mA/cm2, 충실도 54.20% 그리고 변환효율 8.63%를 얻었다.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.8.2-8.2
• /
• 2009

구리(Cu)-인듐(In)-갈륨(Ga)-셀레늄(Se)의 4 원소 화합물 반도체인 Cu(InGa)$Se_2$ (CIGS) 태양전지 세계 최고 셀효율은 2008년 현재 19.9% 로서 박막형 태양전지 중 가장 높은 효율을 보이고 있다. 이는 다결정(폴리) 실리콘 태양전지의 20.3%와 대등한 수준이다. 이 CIGS 태양전지는 제조단가를 표준 결정형 실리콘 태양전지 대비 50% 대로 획기적으로 낮출 수 있어 가장 경쟁력이 있는 차세대 재료로 꼽히고 있다. 본 연구에서는 CIGS태양전지를 고진공 물리 증작법으로 제작하였으며 표면과 박막의 순도를 외부오염을 방지하기 위하여 후면전극, 광흡수체 및 전면전극을 동일 진공에서 제작할 수 있는 멀티 챔버 클러스터 증착 시스템을 이용하였다. 기판으로 소다라 임유리, 후면전극으로 Mo, 전면전극으로 I-ZnO/Al:ZnO 및 ITO를 이용하였다. 버퍼층으로 CdS를 chemical bath deposition (CBD)를 이용하였다. 소자는 무반사막을 사용하지 않고 Al/Ni전극 그리드를 이용하였다. 이 소자로부터 0.22 $cm^2$에서 16%의 효율을 얻었다. 각 박막층 간 계면의 분석을 전기적인 특성, ellisometry에 의한 광특성, 표면과 결정성에 대한 SEM 및 XRD의 특성을 보고한다. 또한, 대표적 화합물 반도체 박막 태양전지인 CIGS 태양전지의 기술의 현황, 학문적인 과제 및 실용화의 문제점을 발표하기로 한다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.374-374
• /
• 2011

Cu(In,Ga)Se2 (CIGS) 박막 태양전지는 일반적으로 Soda lime glass/Mo/CIGS/CdS/ZnO/ITO/Al의 구조로 제작된다. 태양전지는 p형과 n형 반도체의 접합에 의해서 동작을 하게 되며, CIGS 박막 태양전지에서는 p형으로 CIGS 박막과 n형으로 CdS 박막이 사용된다. CIGS 박막태양전지에서는 p형과 n형이 서로 다른 물질로 이루어진 이종접합을 이루게 되고, 계면에서의 밴드가 어떻게 형성이 되느냐에 따라 태양전지 성능에 영향을 미치게 된다. p형의 CIGS 박막은 주로 다단계 증발법에 의해 형성되고 3단계 공정조건에 의해 계면의 특성에 많은 영향을 미치게 된다. n형의 CdS 박막은 주로 chemical bath deposition (CBD) 법에 의해 제작된다. 이렇게 제작되는 CBD-CdS는 시약의 농도, pH (수소이온농도), 박막 형성시의 온도 등의 조건에 따라 특성이 변하게 된다. 본 논문에서는 3단계 공정시간을 변화시켜 제작된 CIGS 박막 위에 CBD-CdS 증착 조건 중 thiourea 의 농도를 변화시켜 CIGS 태양전지를 제작하고 그에 따른 특성을 살펴보았다. CIGS 박막은 3단계 공정시간을 490초와 360초로 하여 제작하였고, CdS 박막은 thiourea 농도를 각각 0.025 M과 0.05 M, 0.074 M, 0.1 M로 변화시켜가며 제작하였다. 제작된 CIGS 박막 태양전지는 CIGS 3단계 공정시간과 thiourea의 조건에 따라 최고 15.81%, 최저 14.13%로 나타내었다. 또한, 외부양자효율을 측정하여 제작된 CIGS 박막 태양전지의 파장에 따른 특성을 비교하였다.

• Journal of Environmental Science International
• /
• v.11 no.7
• /
• pp.651-662
• /
• 2002

Weather elements were observed by the AWS (Automatic Weather System) and dustfall particles were collected by the modified American dust jar (wide inlet bottle type) at 4 sampling sites in Busan area from March. 1999 to February, 2000. Thirteen chemical species (Al, Ca, Cd, Cr, Cu, Fe, K, Mg, Mn, Ni, Pb, Si, and Zn) were analyzed by AAS and ICP. The purposes of this study were to estimate qualitatively various bulk deposition flux of dustfall and insoluble components by applying regional and seasonal wind intensity. Frequency of wind speed were found in order of low(1-3m/s), very low(<1m/s), medium(3-8m/s) and high(>8m/s), and annual mean had higher range at low(1-3m/s) for 56.3%. Strong negative linear correlation were observed between dustfall and wind direction (northeastern and eastern), but strong positive linear correlation were observed between dustfall and wind direction (western and northwestern) at industrial, commercial and coastal zone(p<0.05). While a negative correlation were observed between wind speed frequency of very low(<1 m/s) and dustfall, and positive correlation were observed between wind speed frequency of low(1-3m/s) and dustfall in coastal zone(p<0.05). The correlation coefficient was observed 0.556 between wind speed frequency of low(1-3m/s) and Ni by commercial zone(p<0.05). The correlation coeffcient show well-defined insoluble trace metals (Al, Ca, Cr, Cu, Fe, Pb, and Zn) and wind speed frequency of low(1-3m/s) at coastal zone, which was found significant difference(p<0.01).

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.16 no.4
• /
• pp.169-179
• /
• 2011

To investigate the controlling factor and accumulation of trace metal concentrations in Chun-su Bay sediments, grain-size, specific surface area, organic carbon content, calcium carbonate content, and concentration of Al, Fe, Na, K, Mg, Ca, Ti, Mn, P, S, Ba, Sr, Li, Co, Cr, Ni, Cu, Zn, As, Cd, Cs, Sc, V, Sn were analyzed. Controlling factors of metals were quartz-dilution, calcium carbonate and coarse sand or K-feldspar. Although the distribution of V, Co, Cr, Ni, Cu, Zn, Sn, and Cd concentration was explained by grain-size effiect, Mn and As showed the similar importance of grain-size effect and coarse sand or K-feldspar factors. By virtue of enrichment factor and 1 M HCl experiment, there were little enrichment in all the trace metals in bay sediments, which were explained well by geochemical properties of sediments. Since the concentration levels of As in coarse sand were high as much as those in fine-grained sediments and it was combined with Mn oxide (1 M HCl leached) and K-feldspar (residual), it was suggested that when the enrichment of As in sediments would be assessed, it is necessary to separate the coarse sand from bulk sediments or to use only sediments with higher than 10% in < $16{\mu}m$ fraction.

• Journal of the Korean Ceramic Society
• /
• v.48 no.4
• /
• pp.328-333
• /
• 2011

The influence of Al-doped ZnO (AZO) thin films degraded under high temperature and damp heat on the performance deterioration of Cu(In,Ga)$Se_2$ (CIGS) solar cells was investigated. CIGS solar cells with AZO/CdS/CIGS/Mo structure were prepared on glass substrate and exposed to high temperature ($85^{\circ}C$) and damp heat ($85^{\circ}C$/85% RH) for 1000 h. As-prepared CIGS solar cells had 64.91% in fill factor (FF) and 12.04% in conversion efficiency. After exposed to high temperature, CIGS solar cell had 59.14% in FF and 9.78% in efficiency, while after exposed to damp heat, it had 54.00% in FF and 8.78% in efficiency. AZO thin films in the deteriorated CIGS solar cells showed increases in resistivity up to 3.1 times and 4.4 times compared to their initial resistivity after 1000 h of high temperature and damp heat exposure, respectively. These results can be explained by the decreases in carrier concentration and mobility due to diffusion or adsorption of oxygen and moisture in AZO thin films. It can be inferred that decreases in FF and conversion efficiency were caused by an increase in series resistance, which resulted from an increase in resistivity of AZO thin films degraded under high temperature and damp heat.

• Korean journal of food and cookery science
• /
• v.4 no.1
• /
• pp.53-57
• /
• 1988

To obtain basic data for the development of domestic tea manufacture, the physico-chemical properties were analyzed. The content of crude fiber in domestic black tea was abundant of 50%, as compared with those in Sri-Lanka's black tea, while the contents of tanin and caffeine were lower than those of Sri-Lanka's Products. The quantities of mineral in Sri-Lanka's products were determined as 300ppm P, 15,000ppm K, 1,400ppm Mg, 4,000ppm Ca, 22ppm Cu, 21ppm Cr and 45ppm Zn. These contents were higher than those of domestic products. Al content was 4,100ppm in domestic products. Pb and Cd were not detected in two kinds of black tea products. In Sri-Lanka's black tea, 8 kinds of organic acids were identified and the major organic acids were shikimic, citric and quinic acid, while 6 kinds of organic acids were identified in domestic products and were quinic and gallic acid, as the major organic acids. The content of sucrose was higher than that of Sri-Lanka's product and theaflavin, thearubigin and theobromine were abundant, as compared with those in domestic products.

• Korean Journal of Materials Research
• /
• v.4 no.5
• /
• pp.524-534
• /
• 1994

The effects of transformation temperature and mechanical properties by thermal cycle of CuZnAl shape memory alloy with a small of misch metal and Zr contents were investigated. The addition of misch metal and Zr was very effective for reducing the grain size. After solution treatment, the specimens were post-quench aged or step quenched at $100^{\circ}C$ to $350^{\circ}C$ for variation of Rockwell hardness value. It was found that the Rockwell hareness value was very increased at $200^{\circ}C$ and $250^{\circ}C$. The fracture strength and ductility have been significantly increased with the increase of misch metal conten when tensile tested below $M_f$ temperature. Also, the fracture strength has been more increased in the case of post quench aging treatment than that of the as-quenching treatment. Aging of the $\beta$-phase decreases the $M_s$ temperature, but that of the martensite phase increases the $A_s$ temperature. The change in $A_s$ temperature with post-quench aging can be attributed to recovery of order in the $\beta$phase. The hystersis of transformation temperature ($A_s-M_s$) has an increasing tendency by thermal cycles.

• Journal of Korea Foundry Society
• /
• v.38 no.6
• /
• pp.111-120
• /
• 2018

In this study, the effects of two different casting methods (gravity casting and, diecasting) and various solid-solution conditions on the mechanical properties of ASC (Al-10.5wt%Si-1.75wt%Cu) and ALDC12 (Al-10.3wt%Si-1.72wt%Cu-0.76wt%Fe-0.28wt% Mn-0.32wt%Mg-0.9wt%Zn) alloys were investigated. A thermodynamic solidification analysis program (PANDAT) was used to predict the liquidus, solidus, and phases of the used alloys. In the results of an XRD analysis, ${\beta}$-AlFeSi peaks were observed only in the ALDC12 alloy regardless of the casting method or SST (solid-solution treatment) conditions. However, according to the results of a FE-SEM observation, both ${\theta}(Al_2Cu)$ and ${\beta}$-AlFeSi were found to exist besides ${\alpha}$-Al and eutectic Si in the gravity-casted ASC alloy at $500^{\circ}C$ after a SST of 120min. The ${\alpha}$-AlFeSi and ${\beta}$-AlFeSi phases including the eutectic phases were also found to exist in the ALDC12 alloy. The results of a microstructural observation and analyses by XRD, FE-SEM and EDS were in good agreement with the PANDAT results. The gravity-casted ALDC12 and ASC specimens showed the highest Y.S. and UTS values after aging for three hours at $180^{\circ}C$ after a SST at $500^{\circ}C$ for 30min. At longer solid-solution treatment times at $500^{\circ}C$ in the gravity-casted ALDC12 and ASC specimens, the elongations of the ASC alloys increased, whereas they decreased slightly in the ALDC12 alloys.

• Ocean and Polar Research
• /
• v.25 no.4
• /
• pp.447-457
• /
• 2003

In order to understand the distribution of changes of geochemical characteristics in surface sediments according to various environmental changes around the artificial Lake Shihwa, surface sediments were sampled at $13{\sim}15$ sites form 1997 to 1999 and analyzed by C/S analyzer, ICP/MS and AAS. The average $S/C_{org}$ ratio was 0.35 in the surface sediments, which is similar to 0.36, the characteristic ratio of marine sediments. Heavy metal contents and enrichment factors in the surface sediments tended to be decreasing from the head to the mouth of the Lake Shihwa. With the deposition of fine-grained sediments in the central part of lake, anoxic water column induced the sulfides compounds with Cu, Cd and Zn. Metals such as Al, Fe, Cr, Co, Ni, Cu, Zn and Cd except for Mn and Pb showed relatively high correlation coefficients among them. The contents of Cr, Co, Ni, Cu, Zn and Cd in the surface sediments of the lake were two to five times higher than those in the lake before dike construction and also in outer part of the dike. These are mainly due to the Input of untreated industrial and municipal waste-waters into the lake, and the accumulation of heavy metals by limitation of physical mixing. Although metal contents of the surface sediments at the sites near the water-gate due to outer seawater inflow tended to be lower than those during the desalination, heavy metals were deposited in areas around the new industrial complex in the evidence of spatial distribution of heavy metals in the sediments. This is mainly due to the input of untreated waste-waters from tributaries.