• Korean Journal of Chemical Engineering
• /
• v.36 no.2
• /
• pp.191-196
• /
• 2019

The phase of Cu,Zn,Al precursors strongly affects the activity of their final catalysts. Herein, the Cu,Zn,Al precursor was prepared by precipitation of $Al^{3+}$ onto primitive, amorphous Cu,Zn precipitate. This precursor turned out to be a phase mixture of zincian malachite and hydrotalcite in which the latter phase was less abundant compared to the co-precipitated precursor. The final catalyst derived from this precursor exhibited a little higher copper surface area and methanol synthesis activity than the co-precipitated counterpart. Therefore, the two precursor phases need to be mixed in an adequate proportion for the preparation of active $Cu/ZnO/Al_2O_3$ catalyst.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.04b
• /
• pp.81-84
• /
• 2004

본 논문은 스크린 프린트 방식을 이용하여 두께 $18{\mu}m$의 ZnS:(Cu,Al) 필름을 제조하여 미세구조와 결정성을 분석하고 형광체로써의 특성을 평가하였다. 영상획득에는 포항 가속기 연구소의 싱크로트론을 이용하였으며 CMOS 영상 센서를 사용하여 DR의 간접방식을 구현하였다. 특성 평가를 위해 SEM 측정, 발광 강도 측정을 하였고, 단색광(Beam size $5mm{\times}2mm$)을 사용하여 test phantom 영상과 물고기 영상을 획득하였다. 획득한 영상의 평가를 위해서 test phantom 영상의 MTF 측정을 하였다 제조된 ZnS:(Cu,Al) 필름의 표면은 육방정계 구조를 가졌으며, 5lp/mm는 73.8%, 10lp/mm는 38.9%, 15lp/mm는 15.4%, 20lp/mm는 12.2%의 MTF를 가졌다. 물고기 영상을 통하여 ZnS:(Cu,Al) 필름을 이용한 고해상도 미세구조영상 획득의 가능성을 확인하였다.

• Journal of the Korean Society for Heat Treatment
• /
• v.19 no.5
• /
• pp.257-261
• /
• 2006

Scandium(Sc) in Al-Zn-Mg-Cu based Al alloy on precipitation phenomenon was compared to a 7001(Al-7.2%Zn-3.2%Mg-1.8%Cu) Al alloy. GP zone and ${\eta}^{\prime}$ phases were the main strengthening phases at low aging temperature under $100^{\circ}C$, but ${\eta}^{\prime}$ and $Al_3Sc$ phases were the main strengthening phases at high aging temperature above $1600^{\circ}C$ in Sc added 7000(Al-7.7%Zn-2.0%Mg-1.9%Cu-0.1%Zr) Al alloy. With the addition of 0.1%Sc in 7000 Al alloy, the activation energy for the GP zone, ${\eta}^{\prime}$ and ${\eta}$ phase decreased compared to the 7001 Al alloy. This result indicates that the Sc accelerated the precipitation for the GP zone, ${\eta}^{\prime}$ and ${\eta}$ phases in 7000 Al alloy. Al-7.7%Zn-2.0%Mg-1.9%Cu-0.1%Zr-0.1 Sc alloy has higher strength than 7001 Al alloy, which has high strength.

• Journal of the Korean Magnetics Society
• /
• v.18 no.1
• /
• pp.43-47
• /
• 2008

[ $ZnO-Bi_2O_3-Al_2O_3-B_2O_3-SiO_2$ ] nano-glass has been prepared by sol-gel method. The mean particle size was 60.3 nm with narrow size distribution. The nano-galss has been used as a sintering aid for the densification of the NiZnCu ferrites. The ferrite was sintered with nano-glass sintering aids at $840{\sim}900^{\circ}C$, 2 h and the initial permeability, quality factor, density, and saturation magnetization were also measured. The initial permeability of 0.5 wt% nano-glass added toroidal sample for NiZnCu ferrites sintered at $900^{\circ}C$ was 193.3 at 1 MHz. The initial permeability and saturation magnetization were increased with increasing annealing temperature. As a result, $ZnO-Bi_2O_3-Al_2O_3-B_2O_3-SiO_2$ nano-glass systems were found to be useful as sintering aids for multilayer chip inductors.

• Korean Journal of Optics and Photonics
• /
• v.26 no.5
• /
• pp.265-268
• /
• 2015

An inorganic electroluminescence device based on a green ZnS:(Cu,Al) phosphor was fabricated by a screen printing method. Graphene was added to the phosphor layer to increase the electroluminescence intensity. As the graphene concentration increased, the photoluminescence intensity decreased; on the other hand, the electroluminescence intensity increased, up to 0.6 wt%.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.20 no.3
• /
• pp.60-70
• /
• 2012

Zn, Cu, Fe, Al contents of sludges produced from sewage treatment plants and night soil treatment plant in Pocheon City, Gyeong-gi Province were investigated. And the accumulated contents of those metals in the earthworm Eisenia fetida were also investigated while 15, 30, 45, 60, 75, 90, 105 grams(dw) of sludges were cumulatively supplied to the earthworms. Zn contents of sludges were 75.1~196.1 mg/kg, Cu contents 3.74~76.1 mg/kg, Fe contents 219.9~857.8 mg/kg, Al contents 198.4~991.7 mg/kg, all of which would not cause acute toxicity to the earthworm, but could cause sublethal effects on earthworm and reduce the density of next generation's population. However, cumulative supplies of sludges didn't increase the bioaccumulation rates of metals in the earthworm body, and BAFs of those metals after 60g of sludge supply were 0.0~0.43, which meant that the accumulated Zn, Cu, Fe, Al contents in the earthworm were lower than those of sludges.

• Korean Journal of Materials Research
• /
• v.21 no.1
• /
• pp.67-71
• /
• 2011

La doped CuO-ZnO-$Al_2O_3$ powders are prepared by sol-gel method with aluminum isopropoxide and primary distilled water as precursor and solvent. In this synthesized process, the obtained metal oxides caused the precursor such as copper (II) nitrate hydrate and zinc (II) nitrate hexahydrate were added. To improve the surface areas of La doped CuO-ZnO-$Al_2O_3$ powder, sorbitan (z)-mono-9-octadecenoate (Span 80) was added. The synthesized powder was calcined at various temperatures. The dopant was found to affect the surface area and particle size of the mixed oxide, in conjunction with the calcined temperature. The structural analysis and textual properties of the synthesized powder were measured with an X-ray Diffractometer (XRD), a Field-Emission Scanning Electron Microscope (FE-SEM), Bruner-Emmett-Teller surface analysis (BET), Thermogravimetry-Differential Thermal analysis (TG/DTA), $^{27}Al$ solid state Nuclear Magnetic Resonance (NMR) and transform infrared microspectroscopy (FT-IR). An increase of surface area with Span 80 was observed on La doped CuO-ZnO-$Al_2O_3$ powders from $25m^2$/g to $41m^2$/g.

• Resources Recycling
• /
• v.14 no.1
• /
• pp.17-25
• /
• 2005

In order to recover valuable metals from the waste electronic scrap, bioleaching of Cu, Zn, Al, Co, Ni, Sn and Pb was carried out using Thiobacillus ferrooxidans as a leaching microorganism in a shaking flask. In a preliminary study, to obtain the data on the leaching of Cu, Zn, Al, Co and Ni, the metal leaching was accomplished using metal powers instead of electronic scrap. The leaching percentaga of Cu, Zn, Co, Al and Ni powers was reduced with the increase of metal power concentration in solution. Below the metal concentration of 0.5 g/L, more than 85% of Cu, Co and Zn powers was leached out. At the electronic scrap concentration of 100 g/L, Thiobacillus ferrooxidans were able to leach more than 90% of the available Cu and Co while Al, Zn and Ni were able to leach less than 40%. Pb and Sn were not detected in the leachate. Pb was precipitated as PbSO$_4$, whereas Sn precipitated probably as SnO.

• Journal of the Korean Society for Heat Treatment
• /
• v.3 no.2
• /
• pp.1-9
• /
• 1990

Since the reverse shape memory effect(RSME) was reported in a CuZnAl alloy, further study has been done on the mechanism of this phenomenon and reported that it occurs by the bainitic transformation. But the present authors revealed in the previous work that the RSME in a B2 CuZnAl alloy is not caused by the shear process involved in the bainitic transformation and also that the RSME takes place as the remaining ${\alpha}^{\prime}{_2}$ phase, which is two-step transformed strain induced martensite, is newly transformed into ${\alpha}$ phase. In order to provide further evidence in supporting the facts, thus, more detailed investigations have been carried out in a $DO_3$ CuZnAl alloy.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.322-323
• /
• 2008

Multi layered thin films with ZnS/$Na_3AlF_6$/ZnS were deposited on glass substrate by thermal evaporator precess and simulated by using EMP(Essential Macleod Program). EMP is a comprehensive software package to design and analyse the optical characteristics of multi-layered thin film. ZnS and $Na_3AlF_6$ were selected as a high refractive index and low refractive index material respectively. Additionally Cu was chosen as mid reflective material. Optical properties including color effect were systematically studied. in terms of different optical thickness of low refractive index material. The optical thickness of $Na_3AlF_6$ was changed as 0.25, 0.5, 0.75 and $1.0\lambda$. The film with 0.25, 0.5, 0.75 and $1.0\lambda$. of optical thickness showed mixed color range between bluish green and red purple, yellowish green and bluish green, purple and mixed color range of green and purple respectively.