• Journal of Sensor Science and Technology
• /
• v.18 no.1
• /
• pp.54-62
• /
• 2009

${Co_3}{O_4}$ and ${Co_3}{O_4}$-based thick films with additives such as ${Co_3}{O_4}-{Fe_2}{O_3}$(5 wt.%), ${Co_3}{O_4}-{SnO_2}$ (5 wt.%), ${Co_3}{O_4}-{WO_3}$(5 wt.%) and ${Co_3}{O_4}$-ZnO(5 wt.%) were fabricated by screen printing method on alumina substrates. Their structural properties were examined by XRD and SEM. The sensitivities to iso-${C_4}H_{10}$, $CH_4$, CO, $NH_3$ and NO gases were investigated with the thick films heat treated at $400^{\circ}C$, $500^{\circ}C$ and $600^{\circ}C$. From the gas sensing properties of the films, the films showed p-type semiconductor behaviors. ${Co_3}{O_4}-{SnO_2}$(5 wt.%) thick film heat treated at $600^{\circ}C$ showed higher sensitivity to i-${C_4}H_{10}$ and CO gases than other thick-films. ${Co_3}{O_4}-{SnO_2}$(5 wt.%) thick film heat treated at $600^{\circ}C$ showed the sensitivity of 170 % to 3000 ppm iso-${C_4}H_{10}$ gas and 100 % to 100 ppm CO gas at the working temperature of $250^{\circ}C$. The response time to i-${C_4}H_{10}$ and CO gases showed rise time of about 10 seconds and fall time of about $3{\sim}4$ minutes. The selectivity to i-${C_4}H_{10}$ and CO gases was enhanced in the ${Co_3}{O_4}-{SnO_2}$(5 wt.%) thick film.

• Journal of Sensor Science and Technology
• /
• v.4 no.2
• /
• pp.45-50
• /
• 1995

The excellent c-axis oriented zinc oxide thin films were prepared by the RF magnetron sputtering method on glass substrates. Optimum fabrication conditions of the ZnO films were such that RF power, substrate temperature, and gas pressure of mixture Ar(50%):$O_{2}$(50%) were 150 W, $200^{\circ}C$, and 5 mTorr, respectively. In these conditions, the deposition rate was $310\;{\AA}/min$, and the resistivity of the film was $1{\times}10^6\;{\Omega}{\cdot}cm$. The ZnO film also showed high c-axis orientation and crystalinity according to XRD pattern and SEM photograph. A fabricated interdigital transducer generated 1st mode surface acoustic wave at 46.6 MHz and 2nd mode surface acoustic wave at 52.5 MHz. At the 1st mode, the phase velocity of surface acoustic wave and the electromechanical coupling coefficient were 2795 m/sec and 0.031 %, respectivly. At the 2nd mode, they were 3149 m/sec and 0.019 %. respectivly.

• Journal of Sensor Science and Technology
• /
• v.6 no.6
• /
• pp.476-482
• /
• 1997

A portable electronic nose system has been fabricated and characterized using an oxide semiconductor gas sensor array and pattern recognition techniques such as principal component analysis and back-propagation artificial neural network. The sensor array consists of six thick-film gas sensors whose sensing layers are Pd-doped $WO_{3}$, Pt-doped $SnO_{2}$, $TiO_{2}-Sb_{2}O_{5}-Pd$-doped $SnO_{2}$, $TiO_{2}-Sb_{2}O_{5}-Pd$-doped $SnO_{2}$ + Pd coated layer, $Al_{2}O_{3}$-doped ZnO and $PdCl_{2}$-doped $SnO_{2}$. The portable electronic nose system consists of an 16bit Intel 80c196kc as CPU, an EPROM for storing system main program, an EEPROM for containing optimized connection weights of artificial neural network, an LCD for displaying gas concentrations. As an application the system has been used to identify 26 carbon monoxide/hydrocarbon (CO/HC) car exhausting gases in the concentration range of CO 0%/HC 0 ppm to CO 7.6%/HC 400 ppm and the identification has been successfully demonstrated.

• Journal of the Korean Vacuum Society
• /
• v.18 no.4
• /
• pp.259-265
• /
• 2009

We fabricated the field effect transistor using single crystalline ZnO nanowires synthesized by a conventional thermal evaporation method and investigated their basic properties under the various conditions such as ultraviolet irradiation, reducing gas and electrolyte. The typical carrier concentration and mobility of the single crystalline ZnO nanowire with a diameter of 100 nm and length of 5 um were $1.30{\times}10^{18}cm^{-3}$ and $15.6cm^2V^{-1}s^{-1}$, respectively. The current of ZnO nanowire under ultraviolet irradiation significantly increased about 400 times higher as compared to in the darkness. In addition, the ZnO nanowire showed typical sensing characteristics for $H_2$ and CO due to well-known surface reactions and typical current-voltage characteristics under the 0.1 M NaCl electrolyte.

• Korean Journal of Materials Research
• /
• v.18 no.10
• /
• pp.529-534
• /
• 2008

The hydrogen gas sensing properties of a zinc oxide nanowire structure were studied. Porous zinc oxide nanowire structures were fabricated by oxidizing zinc deposited on a single-wall carbon nanotube (SWNT) template. This revealed a porous ZnO-SWNT composite due to the porosity in the SWNT film. The gas sensing properties were compared with those of zinc oxide thin films deposited on SiO2/Si substrates in sensitivity and operating temperature. The composite structure showed higher sensitivity and lower operating temperature than the zinc oxide film. It showed a response even at room temperature while the film structure did not.

• Korean Chemical Engineering Research
• /
• v.48 no.2
• /
• pp.218-223
• /
• 2010

The zinc oxide thin film, which can be applied as the gas sensor of a semiconductor type, was grown on the silicon substrate by CFR(continuous flow reaction) method in this study. The growth property and the electrical property of the zinc oxide thin films synthesized by CFR method were also investigated. Zinc acetate solutions of 0.005~0.02 M were used as the precursor for the preparation of zinc oxide thin films. The size of ZnO particles consisted on the zinc oxide thin film increased not only with increasing concentration of precursor, but also the thickness of thin film increased. The growth rate of zinc oxide thin film by CFR method was proportionably depend on the concentration of precursor and the uniform ZnO thin film was prepared when zinc acetate of 0.01 M is used as the precursor. The charged currents on the zinc oxide thin films were obtained as its electrical property by I-V meter, and increased agree with increasing the thickness of zinc oxide thin film. Thus, it was concluded that the charged current on the zinc oxide thin film can be controlled with changing concentration of precursor solution in CFR method. The charged currents on the zinc oxide thin films also decreased when ZnO thin film is exposed under hydrogen sulfide of 500 ppmv at $300^{\circ}C$ for 5 min. From these results, it could be confirmed that the zinc oxide thin film prepared by CFR method can be used for the detection of sulfur compounds.

• Proceedings of the Korea Contents Association Conference
• /
• 2008.05a
• /
• pp.595-597
• /
• 2008

Zinc Oxide(ZnO) thin films on Si (100) substrate were deposited by RF magnetron sputter with changing sputtering conditions such as argon/oxygen gas ratios, RF power, and substrate temperature, chamber pressure and target-substrate distance. To analyze a crystallographic properties of the films, ${\Theta}/2{\Theta}$ mode X-ray diffraction, SEM analyses. C-axis preferred orientation highly depended on RF power.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2008.02a
• /
• pp.99-99
• /
• 2008

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.281-281
• /
• 2008

최근 높은 비표면적, 우수한 결정성, 나노스케일의 크기 등 다양한 물리 화학적 특성을 지닌 1차원 나노구조체를 이용한 가스센서 연구가 활발히 진행되고 있다. 가스센서는 네트워크 된 나노선들 이용하여 벌크, 박막 보다 극대화된 비표면적으로 가스 감도와 반응 속도를 향상시킬 수 있었다. 촉매 첨가를 위해 Acetylacetone 용액 7 ml에 10 mM이 되도록 Pt 분말을 첨가하여 촉매용액을 제조하였다. 마이크로피펫을 이용하여 미량을 센서의 감응체 부문에 뿌려 대기 중에서 건조한 후 센서의 감도를 측정하였다. 측정은 $250^{\circ}C$에서 일산화탄소 가스 500 ppm의 가스농도로 촉정하였을 때 촉매가 첨가된 센서가 70% 이상의 개선된 감도를 나타내었다. 이는 나노선에 분산된 촉매에 주입되는 가스가 흡착되고 다시 표면의 산소와 반응하여 전기전도도를 변화시키는 것으로 보인다. 첨가된 촉매에 대한 영향을 분석하기 위해 AES, XRD, FT-IR, TEM 등의 분석을 실시하였다.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.7
• /
• pp.308-314
• /
• 2005

The 2 GHz film bulk acoustic wave resonator(FBAR), one of the most necessary device of the next generation mobile communication system, consisted of solidly mounted resonator(SMR) structure using Brags reflector, was researched in this paper The FBAR applied SiO$_{2}$ and W had large difference of the acoustic impedance to reflector Al to electrode and ZnO to piezoelectric layer. Specially, the FBAR applied the two-step deposition method to improve the c-axis orientation and increase reproducibility of the fabrication device had good performance. The electrical properties of plasma such as impedance, resistance, reactance, $V_{pp},\;I{pp}$, VSWR and phase difference of voltage and current, was analyzed and measured by RF sensor with the variable experiment process factors such as gas ratio, RF power and base vacuum level about concerning the thickness, c-axis orientation, adhesion and roughness. The FBAR device about the optimum condition resulted reflection loss(S$_{11}$) of -17 dB, resonance frequency of 1.93 GHz, electric-mechanical coefficient(k$_{eff}$) of 2.38 $\%$ and Qualify factor of 580. It was seen better qualify than the common dielectric filter at present and expected on business to the filter device of 2 GHz bandwidth with the MMIC technology.