• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.279-279
• /
• 2007

Synthesis and dielectric properties of glass-ceramic composites with zinc borosilicate glass(here after ZBS glass) were investigated as functions of $ZnAl_2O_4$ phase synthesis method, glass addition (50~60 vol%) and sintering temperature ($600{\sim}950^{\circ}C$ for 2 hrs). The 50 vol% ZBS glass-$Al_2O_3$ and 60 vol% ZBS glass-$ZnAl_2O_4$ ensured successful sintering below $900^{\circ}C$. But the composition of 100-x-y vol% ZBS glass-x vol% $Al_2O_3-y$ vol% ZnO exhibited poor sinterability below $900^{\circ}C$ and the swelling phenomenon occurred in this composite with the large amount of ZBS glass. The sintering behavior of Glass-ceramic composites was affected by the crystallization of $ZnAl_2O_4$ which was formed by the reaction between ZBS glass and $Al_2O_3$. Dielectric constant (${\varepsilon}_r$), $Q{\times}f$ value and temperature coefficient of resonant frequency (${\tau}_f$) of the composite with 50 and 60 vol% ZBS glass contents demonstrated $ZBS-Al_2O_3({\varepsilon}_r=5.7)$, $ZBS-ZnAl_2O_4({\varepsilon}_r=5.8)$ which is applicable to substrate requiring an low dielectric properties.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.74-76
• /
• 1995

ZnO varistor with composition of ZnO(90wt%)-Bi$_2$O$_3$(3wt%)-Sb$_2$O$_3$(3.6wt%)-CO$_2$O$_3$(1.16wt%)-NiO(0.88wt%)-MnO$_2$(0.71wt%)-Cr$_2$O$_3$(0.93wt%) according to Al$_2$O$_3$addtive was fabricated by sintering methods. The effects of Al$_2$O$_3$dopant on the I-V characteristics of ZnO varistors were investigated. These changes of electric properties were found to be caused by the variation of grains and grain boundary related to Al$_2$O$_3$dopting. And the conductive mechanism of ZnO varistor in prebreakdown region were investigated with defect model.

• Journal of the Korean Ceramic Society
• /
• v.45 no.5
• /
• pp.256-262
• /
• 2008

$ZnAl_{1-x}\;Cr_xO_4$ solid solutions were synthesized as pink pigments with and without mineralizer. The pigments were examined to optimize color development conditions of temperature and $Cr_2O_3$ contents. The characteristics of synthesized pigments were analyzed by XRD, XPS, FT-IR and UV-vis spectrophotometer. While samples without mineralizer fired at $1300^{\circ}C$, showed $ZnAl_2O_4$ and $ZnCr_2O_4$ spinel in XRD analysis. While samples with mineralizer resulted in $ZnAl_2O_4$. As a results, the pigments show pink color and most effective pink color was obtained at X=0.15 and $1250^{\circ}C$ when mineralizer was used. The chromatic coordinates are $L^*$ 58.61 $a^*$ 24.48, and $b^*$ 9.60.

• Journal of the Korean Ceramic Society
• /
• v.33 no.2
• /
• pp.149-154
• /
• 1996

ZnO and Al-doped ZnO thin films were prepared by sol-gel dip-coating method and electrical and optical properties of films were investigated. Using the zinc acetate dihydrate and acetylaceton(AcAc) as a chelating agent stable ZnO sol was synthesized with HCl catalyst. Adding aluminium chloride to the ZnO sol Al-doped ZnO sol could be also synthesized. As Al contents increase the crystallinity of ZnO thin film was retarded by increased compressive stress in the film resulted from the difference of ionic radius between Zn2+ and Al3+ The thickness of ZnO and Al-doped ZnO thin film was in the range of 2100~2350$\AA$. The resistivity of ZnO thin films was measured by Van der Pauw method. ZnO and Al-doped ZnO thin films with annealing temperature and Al content had the resistivity of 0.78~1.65$\Omega$cm and ZnO and Al-doped ZnO thin film post-annealed at 40$0^{\circ}C$ in vacuum(5$\times$10-5 torr) showed the resistivity of 2.28$\times$10-2$\Omega$cm. And the trans-mittance of ZnO and Al-doped ZnO thin film is in the range of 91-97% in visible range.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.191-191
• /
• 2003

가시광선영역에서 높은 광학적 투명도를 갖는 n-type 반도체인 ZnO 박막은 넓은 범위에서 응용되고 있다. 현재 ZnO 박막의 특성 향상을 위하여 여러 원소(Al, Ga)의 도핑을 시도하고 있다. 특히 Al-doped ZnO 박막은 sol-gel dip coating에 의해서도 높은 전기전도도와 투과율로 활발히 연구되고 있다 본 논문에서는 여러 도핑농도를 갖는 Al-doped ZnO 박막이 sol-gel dip coating법에 의해 준비되었다. Al-doped ZnO 박막은 zinc acetate [Zn($CH_3$COO$_2$)ㆍ2$H_2O$] powder 와 여러 도핑농도를 갖는 aluminum nitrate (Al(NO$_3$)$_3$ㆍ9$H_2O$) powder를 알코올에 용해하여 $H_2O$, Ethylene glycol, Ethylene diamine 등을 첨가하여 제조하였다 XRD와 SEM (Scanning electron microscope)이 막의 상형성 분석을 위해 이용되었으며, 가시광선 영역 투과율(UV/VIS spectrophotometer)과 표면전기저항(four point probe)이 주요 특성으로 분석되었다.

• Korean Journal of Materials Research
• /
• v.5 no.3
• /
• pp.280-287
• /
• 1995

첨가제로 $Al_{2}$$O_{3}$가 포함된 ZnO 소결체가 타깃을 이용하여 RF 마그네트론 스퍼터링법으로 Al이 첨가된 ZnO박막을 증착하고, 타깃에 첨가된 $Al_{2}$$O_{3}$의 농도와 증착시 스퍼터링장치내의 기판위치에 따른 박막의 물성 변화를 고찰하였다. 타깃의 $Al_{2}$$O_{3}$ 첨가농도가 2wt%인 경우에 비저항치 8 $\times$ $10_{-3}$ $\Omega$-cm인 박막이 증차되었다. 또한 $Al_{2}$$O_{3}$가 2wt%이상 첨가된 경우는 모든 Al이 박막내부에서 Zn를 치환하여 전자주게로의 역할을 하지 못하고, 오히려 치환되지 못한 Al원자의 중성 불순물 산란효과에 의해 박막의 비저항이 증가하였다. 타깃의 마모영역 위에서 증착된 Al을 첨가한 ZnO 박막은 그 영역 KR에서 증착된 박막보다 높은 비저항값을 나타냈으며, 이는 큰 에너지를 가지는 산소입자의 충돌에 기인한 것으로 여겨진다.

• Electrical & Electronic Materials
• /
• v.9 no.6
• /
• pp.572-577
• /
• 1996

Alternating current and direct current of pure, ball milled, and $Al_{2}$O$_{3}$ added ZnO were investigated by means of complex impedance measurement and voltage-current source measurement unit. The electrical conductivity of A1$_{2}$O$_{3}$ added ZnO samples increases when the content of A1$_{2}$O$_{3}$ is used within 1 at% and decreases when it's used more than that. The increase and decrease of electrical conductivity seem to be the donor effect of $Al_{2}$O$_{3}$ and the increase of the number of ZnO grains, respectively. Impedance spectrum seems to be one semircicle. The size of semicircle increase with increasing the A1$_{2}$O$_{3}$ contents. The calculated dielectric constant(at 50.deg. C) were about 70-140 at the peak of the semicircle. The semicircles seem not to be the resistance of ZnO grain as compared to that of 10 for pure ZnO.

• Journal of the Korean Magnetics Society
• /
• v.18 no.1
• /
• pp.43-47
• /
• 2008

[ $ZnO-Bi_2O_3-Al_2O_3-B_2O_3-SiO_2$ ] nano-glass has been prepared by sol-gel method. The mean particle size was 60.3 nm with narrow size distribution. The nano-galss has been used as a sintering aid for the densification of the NiZnCu ferrites. The ferrite was sintered with nano-glass sintering aids at $840{\sim}900^{\circ}C$, 2 h and the initial permeability, quality factor, density, and saturation magnetization were also measured. The initial permeability of 0.5 wt% nano-glass added toroidal sample for NiZnCu ferrites sintered at $900^{\circ}C$ was 193.3 at 1 MHz. The initial permeability and saturation magnetization were increased with increasing annealing temperature. As a result, $ZnO-Bi_2O_3-Al_2O_3-B_2O_3-SiO_2$ nano-glass systems were found to be useful as sintering aids for multilayer chip inductors.

• Korean Journal of Chemical Engineering
• /
• v.36 no.2
• /
• pp.191-196
• /
• 2019

The phase of Cu,Zn,Al precursors strongly affects the activity of their final catalysts. Herein, the Cu,Zn,Al precursor was prepared by precipitation of $Al^{3+}$ onto primitive, amorphous Cu,Zn precipitate. This precursor turned out to be a phase mixture of zincian malachite and hydrotalcite in which the latter phase was less abundant compared to the co-precipitated precursor. The final catalyst derived from this precursor exhibited a little higher copper surface area and methanol synthesis activity than the co-precipitated counterpart. Therefore, the two precursor phases need to be mixed in an adequate proportion for the preparation of active $Cu/ZnO/Al_2O_3$ catalyst.

• Current Photovoltaic Research
• /
• v.3 no.1
• /
• pp.32-38
• /
• 2015

CIGS solar cell consisted of various films. In this research, we investigated electrode materials in $Cu(In,Ga)Se_2$ (CIGS) cells, including Al-doped ZnO (ZnO:Al), intrinsic ZnO (i-ZnO), and Al films. The sputtered ZnO:Al film with a sputtering power at 200W showed the lowest series resistance and highest cell efficiency. The electrical resistivity of the 200-W sputtered ZnO:Al film was $5.2{\times}10^{-4}{\Omega}{\cdot}cm$ by the rapid thermal annealing at $200^{\circ}C$ for 1 min. The electrical resistivity of i-ZnO was not measurable due to its high resistance. But the optical transmittance was highest with less oxygen supply and high efficiency cell was achieved with $O_2/(Ar+O_2)$ ratio was 1% due to the increase of short-circuit current. No significant change in the cell performance by inserting a Ni layer between Al and ZnO:Al films was observed.