• Title/Summary/Keyword: Zn-Sn

Search Result 612, Processing Time 0.022 seconds

Improvement in Performance of Cu2ZnSn(S,Se)4 Absorber Layer with Fine Temperature Control in Rapid Thermal Annealing System (Cu2ZnSn(S,Se)4(CZTSSe) 흡수층의 급속 열처리 공정 온도 미세 조절을 통한 특성 향상)

  • Kim, Dong Myeong;Jang, Jun Sung;Karade, Vijay Chandrakant;Kim, Jin Hyeok
    • Korean Journal of Materials Research
    • /
    • v.31 no.11
    • /
    • pp.619-625
    • /
    • 2021
  • Cu2ZnSn(S,Se)4 (CZTSSe) based thin-film solar cells have attracted growing attention because of their earth-abundant and non-toxic elements. However, because of their large open-circuit voltage (Voc)-deficit, CZTSSe solar cells exhibit poor device performance compared to well-established Cu(In,Ga)(S,Se)2 (CIGS) and CdTe based solar cells. One of the main causes of this large Voc-deficit is poor absorber properties for example, high band tailing properties, defects, secondary phases, carrier recombination, etc. In particular, the fabrication of absorbers using physical methods results in poor surface morphology, such as pin-holes and voids. To overcome this problem and form large and homogeneous CZTSSe grains, CZTSSe based absorber layers are prepared by a sputtering technique with different RTA conditions. The temperature is varied from 510 ℃ to 540 ℃ during the rapid thermal annealing (RTA) process. Further, CZTSSe thin films are examined with X-ray diffraction, X-ray fluorescence, Raman spectroscopy, IPCE, Energy dispersive spectroscopy and Scanning electron microscopy techniques. The present work shows that Cu-based secondary phase formation can be suppressed in the CZTSSe absorber layer at an optimum RTA condition.

Varistor Properties of Sn2O3- Doped ZnO-Pr6O11-CoO-Doped -Based Ceramics (Sn2O3가 첨가된 ZnO-Pr6O11-CoO계 세라믹스의 바리스터 특성)

  • 남춘우
    • Journal of the Korean Institute of Electrical and Electronic Material Engineers
    • /
    • v.16 no.1
    • /
    • pp.39-45
    • /
    • 2003
  • The varistor properties of ZnO-Pr$_{6}$O$_{11}$-CoO-based ceramics doped with Sm$_2$O$_3$were investigated in the addition range of 0.0~2.0 mol% Sm$_2$O$_3$at sintering temperature of 130$0^{\circ}C$ and 135$0^{\circ}C$. As Sm$_2$O$_3$ content is increased, the breakdown voltage was increased in the range of 348.9~521.8 V/mm for ceramics sintered at 130$0^{\circ}C$ and 8.5~381.3 V/mm for ceramics sintered at 135$0^{\circ}C$. On the whole, the increase of sintering temperature led to the low nonlinearity regardless of Sm$_2$O$_3$content. ZnO-Pr$_{6}$O$_{11}$-CoO-based ceramics doped with 1.0 mol% at each sintering temperature exhibited the most superior varistor properties, with the nonlinear exponent of 42.1 at 130$0^{\circ}C$, 36.8 at 135$0^{\circ}C$ and the leakage current of 9.2 $\mu$A at 130$0^{\circ}C$, 11.7 $\mu$A at 135$0^{\circ}C$.EX>.EX>.

Study of metal dopants and/or Ag nanoparticles incorporated direct-patternable ZnO film by photochemical solution deposition

  • Kim, Hyun-Cheol;Reddy, A.Sivasankar;Park, Hyung-Ho
    • Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
    • /
    • 2007.11a
    • /
    • pp.368-368
    • /
    • 2007
  • Zinc oxide (ZnO) has drawn much interest as a potential transparent conducting oxide (TCO) for applying to solar cell and front electrode of electro-luminescent devices. For the enhancement of electrical property of TCOs, dopant introduction and hybridization with conductive nanoparticles have been investigated. In this work, ZnO films were formed on glass substrate by using photochemical solution deposition of Ag nanoparticles dispersed or various metal (Ag, Cd, In, or Sn) contained photosensitive ZnO solutions. The usage of photosensitive solution permits us to obtain a micron-sized direct patterning of ZnO film without using conventional dry etching procedure. The structural, optical, and electrical characteristics of ZnO films with the introduction of metal dopants with/without Ag nanoparticles have been investigated to check whether there is a combined effect between metal dopants and Ag nanoparticles on the characteristics of ZnO film. The phase formation and crystallinity of ZnO film were monitored with X-ray diffractometer. The optical transmittance measurement was carried out using UV-VIS-NIR spectrometer and the electrical properties such as sheet resistance and conductivity were observed by using four-point probe.

  • PDF

Element Dispersion by the Wallrock Alteration of Janggun Lead-Zinc-Silver Deposit (장군 연-아연-은 광상의 모암변질에 따른 원소분산)

  • Yoo, Bong Chul
    • Economic and Environmental Geology
    • /
    • v.45 no.6
    • /
    • pp.623-641
    • /
    • 2012
  • The Janggun lead-zinc-silver deposit is hydrothermal-metasomatic deposit. We have sampled wallrock, hydrother-maly-altered rock and lead-zinc-silver ore vein to study the element dispersion during wallrock alteration. The hydrothermal alteration that is remarkably recognized at this deposit consists of rhodochrositization and dolomitization. Wallrock is dolomite and limestone that consisit of calcite, dolomite, quartz, phlogopite and biotite. Rhodochrosite zone occurs near lead-zinc-silver ore vein and include mainly rhodochrosite with amounts of calcite, dolomite, kutnahorite, arsenopyrite, pyrite, chalcopyrite, sphalerite, galena and stannite. Dolomite zone occurs far from lead-zinc-silver ore vein and is composed of mainly dolomite and minor calcite, rhodochrosite, pyrite, sphalerite, chalcopyrite, galena and stannite. The correlation coefficients among major, trace and rare earth elements during wallrock alteration show high positive correlations(dolomite and limestone = $Fe_2O_3(T)$/MnO, Ga/MnO and Rb/MnO), high negative correlations(dolomite = MgO/MnO, CaO/MnO, $CO_2$/MnO, Sr/MnO; limestone = CaO/MnO, Sr/MnO). Remarkable gain elements during wallrock alteration are $Fe_2O_3(T)$, MnO, As, Au, Cd, Cu, Ga, Pb, Rb, Sb, Sc, Sn and Zn. Remarkable loss elements are CaO, $CO_2$, MgO and Sr. Therefore, elements(CaO, $CO_2$, $Fe_2O_3(T)$, MgO, MnO, Ga, Pb, Rb, Sb, Sn, Sr and Zn) represent a potential tools for exploration in hydrothermal-metasomatic lead-zinc-silver deposits.

Effect of Ionic Molar Conductivity on Separation Characteristics of Heavy Metals by Nanofiltration Membranes in Waste Water (이온 몰 전도도가 나노여과막에 의한 폐수 중의 중금속 분리특성에 미치는 영향)

  • Oh, Jeong-Ik
    • Land and Housing Review
    • /
    • v.4 no.1
    • /
    • pp.119-124
    • /
    • 2013
  • Generally, the characteristic of nanofiltration membranes were catagorized into charged membrane, sieve effect, interaction between membarnes and target solutes. This study aims to investigate the effect item of heavy metal separation with view of charge nanofiltration membranes. The experiments of nanofiltration were conducted by nanofiltration set-up with operational pressure of 0.24 MPa at $25^{\circ}C$ by using synthetic wastewater containing 0.1mg/L of Cr, Fe, Cu, Zn, As, Sn, Pb. Nanofiltration membranes rejected heavy metals much better than chloride, sulfate and TOC, of which concentration in synthetic wastewater was higher than that of heavy metals. To consider rejection characteristics of various metals by nanofiltration membranes, separation coefficient, which is the molar conductivity ratio of the metal permeation rate to the chloride ion or TOC permeation rate, was introduced. In spite of different materials and different nominal salt rejection of nanofiltration membrane used, the separation coefficients of metals were nearly the same. These phenomena were observed in the relationship between the molar conductivity and the separation coefficient for heavy metals.

Fabrication and Characterization of Portable Electronic Nose System for Identification of CO/HC Gases (CO/HC 가스 인식을 위한 소형 전자코 시스템의 제작 및 특성)

  • Hong, Hyung-Ki;Kwon, Chul-Han;Yun, Dong-Hyun;Kim, Seung-Ryeol;Lee, Kyu-Chung;Kim, In-Soo;Sung, Yung-Kwon
    • Journal of Sensor Science and Technology
    • /
    • v.6 no.6
    • /
    • pp.476-482
    • /
    • 1997
  • A portable electronic nose system has been fabricated and characterized using an oxide semiconductor gas sensor array and pattern recognition techniques such as principal component analysis and back-propagation artificial neural network. The sensor array consists of six thick-film gas sensors whose sensing layers are Pd-doped $WO_{3}$, Pt-doped $SnO_{2}$, $TiO_{2}-Sb_{2}O_{5}-Pd$-doped $SnO_{2}$, $TiO_{2}-Sb_{2}O_{5}-Pd$-doped $SnO_{2}$ + Pd coated layer, $Al_{2}O_{3}$-doped ZnO and $PdCl_{2}$-doped $SnO_{2}$. The portable electronic nose system consists of an 16bit Intel 80c196kc as CPU, an EPROM for storing system main program, an EEPROM for containing optimized connection weights of artificial neural network, an LCD for displaying gas concentrations. As an application the system has been used to identify 26 carbon monoxide/hydrocarbon (CO/HC) car exhausting gases in the concentration range of CO 0%/HC 0 ppm to CO 7.6%/HC 400 ppm and the identification has been successfully demonstrated.

  • PDF

Electro-chemical corrosion properties of Mg film ion-plated on different interlayers (이온플레이팅법의 의해 제작한 Mg 박막의 중간층에 따른 전기화학적 내식특성)

  • Baek, Sang-Min;Yang, Jeong-Hyeon;Bae, Il-Yong;Mun, Gyeong-Man;Lee, Myeong-Hun
    • Proceedings of the Korean Institute of Surface Engineering Conference
    • /
    • 2007.11a
    • /
    • pp.46-46
    • /
    • 2007
  • Zn, Al 및 Sn을 각각 도금한 강기판상에 Mg박막을 이온플레이팅법에 의해 제작하였다. 이와 같은 중간층을 가진 Mg막의 내식측정결과에 의하면, Mg과 갈바닉 전위차가 작은 Zn을 중간층으로 하여 제작한 Mg 막이 Fe 모재보다 낮은 자연 전위값을 안정적으로 유지하면서 희생양극적 방식효과를 장시간동안 나타내었다.

  • PDF

Surface morphology and electrical properties of ISZO films deposited by magnetron sputting (마그네트론 스퍼터링에 의해 증착한 ISZO 박막의 표면 형상 및 전기적 특성)

  • Lee, Dong-Yeop;Lee, Jeong-Rak;Kim, Do-Geun;Lee, Geon-Hwan;Song, Pung-Geun
    • Proceedings of the Korean Institute of Surface Engineering Conference
    • /
    • 2007.04a
    • /
    • pp.116-117
    • /
    • 2007
  • In-Sn-Zn-O 박막을 2개의 케소드(DC, RF)를 이용해magnetron co-sputtering법으로 polycarbonate (PC)기판위에 성막하였다. ITO와 ZnO 타겟은 각각 DC와 RF power supply에 의해 스퍼터 되었다. ISZO 박막의 가장 낮은 비저항은 RF power 55W 일 때 얻을 수 있었고, 이것은 케리어 밀도의 증가에 의한 것이라 생각되어 진다.

  • PDF

Effect of Nano Particles on Fertilized Egg of Crossostrea gigas (참굴(Crassostrea gigas) 수정란에 미치는 나노입자의 영향)

  • Lee, Byeong-Woo;Park, Chan-Il;Choi, Kwang-Soo;Kim, Mu-Chan
    • Journal of the Korean Society of Marine Environment & Safety
    • /
    • v.14 no.1
    • /
    • pp.9-14
    • /
    • 2008
  • A Nano particle is a small particle with at least one dimension less than 100 nm Nanoparticle is currently used in an area cf intense scientific research, due to a wide variety cf potential applications in biomedical, optical, and electronic fields. In order to know the biological effect of the nine Nano particles on fertilized egg of Crassostrea gigas experiments were performed Development rates of control (free Nano particles) C. gigas to a particular larval stage (D-shape) was 78%. Development rate of C gigas to a parcicular larval stage (D-shape) after 24 hours exposure to 0.05ppm of AGZ020, Nano silver, P-25 and SnO were 22%, 52%, 58% and 76%, respectively. However, all fertilized eggs were destructed within 8 hours afters exposure to 20ppm of respective particles. On the other hand, All fertilized eggs were not affected after 24 hours respective exposure to 0.05ppm of In, Sb, Sn, Zn, and Ag-$TiO_2$ particles. However, development rates of C. gigas after 24 hours exposure to 20ppm of In, Sb, Sn, Zn, Ag-$TiO_2$ were 57%, 60%, 50%, 65%, and 64% respectively.

  • PDF

Raw Material and Provenance of Coin Minted in Goryo Dynasty( I ) : 'Haedong-Tongbo(해동통보) (고려시대 동전의 주조 원료와 산지( I ) -해동통보)

  • Kang, Hyung Tae;Kim, Gyu-Ho;chung, Kwang Yong
    • Journal of Conservation Science
    • /
    • v.17 s.17
    • /
    • pp.33-38
    • /
    • 2005
  • One piece of Haedong-Tongue(해동통보) minted at 1,102 A.D. was excavated from No.20 wooden coffin, Sinbong-dong, Cheongju. It was analyzed by micro-XRF and ICP and determined the concentrations of ten elements such as Cu, Pb, Sn, Zn, Fe, Mn, Sb, Co, As, Ag and Ni. The measurement of lead isotope ratios was also carried out in order to predict the provenance of raw materials used for minting of Haedong-Tongbo. It was found that Haedong-Tongbo was minted with three compositions of $Cu\;75.5\%,\;Pb\;13.3\%\;and\;Sn\;6.0\%$, which were different from the typical composition of Chosen-Tongbo and Sangpyung-Tongbo used in Chosen dynasty. Lead isotope ratios of Haedong-Tongbo showed that the provenance of lead used for minting of it suggested the possibility to be originated from Southern part of Korea.

  • PDF