• Bulletin of the Korean Chemical Society
• /
• v.34 no.5
• /
• pp.1445-1453
• /
• 2013

$Zn_{(1-x)}Ni_xAl_2O_4$ (x = 0.0-1.0) spinels were prepared at $800^{\circ}C$ by co-precipitation method and characterized by infrared spectroscopy, X-ray diffraction, scanning electron microscopy and X-ray photoelectron spectroscopy. The specific surface area was determined by BET. SEM image showed nano sized spherical particles. XPS confirmed the valence states of the metals, showing moderate Lewis character for the surface of materials. The powders were successfully used as new heterogeneous catalysts of Biginelli's reaction, a one-pot three-component reaction, leading to some dihydropyrimidinones (DHPMs). These new catalysts that produced good yields of DHPMs, were easily recovered by simple filtration and subsequently reused with persistent activity, and they are non-toxic and environmentally friendly. The optimum amount of catalyst is 20% by weight of benzaldehyde derivatives, while the doping amount has been found optimal for x = 0.1.

• Korean Journal of Materials Research
• /
• v.12 no.1
• /
• pp.54-57
• /
• 2002

We have grown undoped $In_ xGa_{1-x}N,\; In_xGa_{1-x}N:Si\;and\;In_{0.1}Ga_{0.9}N:Zn$ thin films by MOCVD at temperature between 880 and $710^{\circ}C which endows various In composition in the epilayer from 0.07 to 0.22 as examined using X-ray diffraction, optical absorption(OA), photocurrent (PC) and photoluminescence (PL). The In molar fraction estimated from PL results is higher than that from the OA, PC, and X-ray data for $X{\le}0.22$, which may be caused by phase separation. However, the In molar fraction estimated by X-ray diffraction, OA, PC and PL for $In_xGa_{1-x}N:Si$ does not show discrepancy. With the appropriate Zn doping in undoped $In_{0.1}Ga_{0.9}N$, the emission peak is shifted from 3.15 eV which originates from the band edge emission peak to 2.65 eV which resulted from the conduction band to acceptor transition due to a deep acceptor level.

• Korean Journal of Materials Research
• /
• v.22 no.12
• /
• pp.682-688
• /
• 2012

In this study we aimed to examine the co-doping effects of 1/6 mol% $Co_3O_4$ and 1/4 mol% $Cr_2O_3$ (Co:Cr = 1:1) on the reaction, microstructure, and electrical properties, such as the bulk defects and the grain boundary properties, of ZnO-$Bi_2O_3-Sb_2O_3$ (ZBS; Sb/Bi = 0.5, 1.0, and 2.0) varistors. The sintering and electrical properties of Co,Cr-doped ZBS, ZBS(CoCr) varistors were controlled using the Sb/Bi ratio. Pyrochlore ($Zn_2Bi_3Sb_3O_{14}$), ${\alpha}$-spinel ($Zn_7Sb_2O_{12}$), and ${\delta}-Bi_2O_3$ were formed in all systems. Pyrochlore was decomposed and promoted densification at lower temperature on heating in Sb/Bi = 1.0 by Cr rather than Co. A more homogeneous microstructure was obtained in all systems affected by ${\alpha}$-spinel. In ZBS(CoCr), the varistor characteristics were improved (non-linear coefficient, ${\alpha}$ = 20~63), and seemed to form ${Zn_i}^{{\cdot}{\cdot}}$(0.20 eV) and ${V_o}^{\cdot}$(0.33 eV) as dominant defects. From impedance and modulus spectroscopy, the grain boundaries were found to be composed of an electrically single barrier (0.94~1.1 eV) that is, however, somewhat sensitive to ambient oxygen with temperature. The phase development, densification, and microstructure were controlled by Cr rather than by Co but the electrical and grain boundary properties were controlled by Co rather than by Cr.

• Journal of the Korean Vacuum Society
• /
• v.19 no.1
• /
• pp.66-71
• /
• 2010

Spherical shape $Zn_2SiO_4:Mn$ phosphor particles with the mean particle size from submicron to micron sizes were prepared by ultrasonic spray pyrolysis method. A droplet separator was introduced to control the size distribution of the phosphor particles with spherical shape. The $Zn_2SiO_4:Mn$ phosphor particles with 2 mol% doping concentration of manganese have decay time and have photoluminescence intensities comparable with those of the latest commercial product prepared by the solid state reaction method. The size of the phosphor particles was decreased from 1 to 0.2 micrometers as the inorganic salt solution concentration was changed from 0 to 5 M. The phosphor particles prepared from the solutions above 0.5 M have photoluminescence intensities comparable with that of the latest commercial product.

• New & Renewable Energy
• /
• v.3 no.4
• /
• pp.63-68
• /
• 2007

유리를 기판으로 하는 superstrate pin 비정질 실리콘 태양전진에서 전면 투명전도막(TCO)과 p-층의 계면은 태양전지 변환효율에 큰 영향을 미친다. 면투명전도막(TCO)으로 현재 일반적으로 사용되는 ZnO:Al는 $SnO_2:F$보다 전기, 광학적으로 우수하고, 안개율 (Haze)높으며, 수소 플라즈마에서 안정성이 높은 특징을 갖고 있다. 그래서 박막 태양전지의 특성향상에 매우 유리하나, 태양전지로 제조했을 때, $SnO_2$보다 충진율(Fill Factor:F.F)과 $V_{oc}$가 감소한다는 단점을 가지고 있다. 본 실험실에서는 $SnO_2:F$dml F.F.가 72%이 나온 반면 ZnO:Al의 F.F은 68%에 그쳤다. 이들 원인을 분석하기 위해 TCO/p-layer의 전기적 특성을 알아 본 결과, $SnO_2:F$보다 ZnO:Al의 직렬저항이 높게 측정되었다. 이러한 결과를 바탕으로 p-layer에 $R=(H_2/SiH_4)=25$로 변화, p ${\mu}c$-Si:H/p a-SiC:H로 p-layer 이중 증착, p-layer의 boron doping 농도를 증가시키는 실험을 하였다. 직렬저항이 가장 낮았던 p ${\mu}c$-Si:H/p a-SiC:H 인 p-layer 이중 증착에서 $V_{oc}$는 0.95V F.F는 70%이상이 나왔다. 이들 각 p층의 $E_a$(Activiation Energy)를 구해본 결과, ${\mu}c$-Si:H의 Ea 가 가장 낮은 것을 관찰 할 수 있었다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.2
• /
• pp.114-120
• /
• 2012

In this research, we prepared Ga doped zinc oxide(ZnO:Ga, GZO) targets each difference sintering temperature $700^{\circ}C$, $800^{\circ}C$, and doping rate 1 wt.%, 2 wt.%, 3 wt.%. The characteristics of thin film on glass substrates which deposited by facing target sputtering in pure Ar atmosphere are reported. Ga doped zinc oxide film is attracted material through low resistivity, high transmittance, etc. When prepared target powder's structure was investigated by scanning electron microscope, densification and coarsening by driving force was observed. For each ZnO:Ga films with a $Ga_2O_3$ content of 3 wt.% at input power of 45W, the lowest resistivity of $9.967{\times}10^{-4}{\Omega}{\cdot}cm$ ($700^{\circ}C$) and $9.846{\times}10^{-4}{\Omega}{\cdot}cm$ ($800^{\circ}C$) was obtained. the carrier concentration and mobility were $4.09{\times}10^{20}cm^{-3}$($700^{\circ}C$), $4.12{\times}10^{20}cm^{-3}$($800^{\circ}C$) and $15.31cm^2/V{\cdot}s(700^{\circ}C)$, $12.51cm^2/V{\cdot}s(800^{\circ}C)$, respectively. And except 1 wt.% Ga doped ZnO thin film, average transmittance of these samples in the range 350-800 nm was over 80%.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.275-277
• /
• 2007

유리를 기판으로 하는 superstrate pin 비정질 태양전지에서 전면투명전도막(TCO)과 p-layer의 계면이 태양전지의 효율을 내는데 가장 큰 기여를 한다. 전면투명전도막(TCO)으로 현재 일반적으로 사용되는 ZnO:Al는 $SnO_2:F$ 보다 전기,광학적으로 우수하고, 안개율(Haze)높으며, 수소 플라즈마에서의 안정성이 높은 특정을 갖고 있다. 그래서 박막 태양전지 특성향상에 매우 유리하나, 태양전지로 제조했을 때, $SnO_2:F$보다 충진율(Fill factor:F.F)과 V_{\infty}$ 가 감소한다는 단점을 가지고 있다. 본 실험실에서는 $SnO_2:F$의 F.F가 72%이 나온 반면 ZnO:Al의 F.F은 68%에 그쳤다. 이들 원인을 분석하기 위해 TCO/p-layer의 전기적 특성을 알아 본 결과, $SnO_2:F$보다 ZnO:Al의 직렬저항이 높게 측정되었다. 이러한 결과를 바탕으로 p-layer 에 R={$H_2/SiH_4$}=25로 변화, p ${\mu$}c$-Si:H/p a-SiC:H 로 p-layer 이중 증착, p-layer의 boron doping 농도를 증가시키는 실험을 하였다. 직렬저항이 가장 낮았던 p ${\mu$}c$-Si:H/p a-SiC:H 로 p-layer 이중 증착에서 Voc는 0.95V F.F는 70% 이상이 나왔다. 이들 각 p층의 $E_a$(Activation Energy)를 구해본 결과, ${\mu$}c$-Si:H의 Ea 가 가장 낮은 것을 관찰 할 수 있었다.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.18.2-18.2
• /
• 2010

For the past a few years, we have intensively researched the printable inorganic conductors and ZnO-based amorphous oxide semiconductors (AOSs) for thin-film transistors. For printable conductor materials, we have focused on the aqueous Ag and Cu ink which possess a variety of advantages, comparing with the conventional metal inks based on organic solvent system. The aqueous Ag ink was designed to achieve the long-term dispersion stability using a specific polymer which can act as a dispersant and capping agent, and the aqueous Cu ink was carefully formulated to endow the oxidation stability in air and even aqueous solvent system. The both inks were successfully printed onto either polymer or glass substrate, exhibiting the superior conductivity comparable to that of bulk one. For printable ZnO-based AOSs, we have researched the noble way to resolve the critical problem, a high processing-temperature above $400^{\circ}C$, and recently discovered that Ga doping in ZnO-based AOSs promotes the formation of oxide lattice structures with oxygen vacancies at low annealing-temperatures, which is essential for acceptable thin-film transistor performance. The mobility dependence on annealing temperature and AOS composition was analyzed, and the chemical role of Ga are clarified, as are requirements for solution-processed, low-temperature annealed AOSs.

• Current Photovoltaic Research
• /
• v.4 no.4
• /
• pp.150-154
• /
• 2016

Mg and In co-doped ZnO (MIZO) thin films with transparent conducting characteristics were successfully prepared on glass substrates by RF magnetron sputtering technique. The Influence of different substrate temperature (from RT to $400^{\circ}C$) on the structural, morphological, electrical, and optical properties of MIZO thin films were investigated. The MIZO thin film prepared at the substrate temperature of $350^{\circ}C$ showed the best electrical characteristics in terms of the carrier concentration ($4.24{\times}10^{20}cm^{-3}$), charge carrier mobility ($5.01cm^2V^{-1}S^{-1}$), and a minimum resistivity ($1.24{\times}10^{-4}{\Omega}{\cdot}cm$). The average transmission of MIZO thin films in the visible range was over 80% and the absorption edges of MIZO thin films were very sharp. The bandgap energy of MIZO thin films becomes wider from 3.44 eV to 3.6 eV as the substrate temperature increased from RT to $350^{\circ}C$. However, Band gap energy of MIZO thin film was narrow at substrate temperature of $400^{\circ}C$.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.1
• /
• pp.112-115
• /
• 2010

Transparent conducting undoped and Al impurity doped ZnO films were deposited on glass substrate by spin coat technique using 24 days aged ZnO precursor solution with solution of ethanol and diethanolamine. The films were characterized by UV-Visible spectroscopy, X-ray diffraction (XRD), scanning electron microscope (SEM), electrical resistivity ($\rho$), carrier concentration (n), and hall mobility ($\mu$) measurements. XRD data show that the deposited film shows polycrystalline nature with hexagonal wurtzite structure with preferential orientation along (002) crystal plane. The SEM images show that surface morphology, porosity and grain sizes are affected by doping concentration. The Al doped samples show high transmittance and better resistivity. With increasing Al concentration only mild change in optical band gap is observed. Optical properties are not affected by aging of parent solution. A lowest resistivity ($8.5 \times 10^{-2}$ ohm cm) is observed at 2 atomic percent (at.%) Al. With further increase in Al concentration, the resistivity started to increase significantly. The decrease resistivity with increasing Al concentration can be attributed to increase in both carrier concentration and hall mobility.