• Nuclear Engineering and Technology
• /
• 제49권8호
• /
• pp.1740-1747
• /
• 2017

To investigate allowable peak cladding temperature and hoop stress for maintenance of cladding integrity during interim-dry storage and subsequent transport, zirconium alloy cladding tubes were hydrogen-charged to generate 250 ppm and 500 ppm hydrogen contents, simulating spent nuclear fuel degradation. The hydrogen-charged specimens were heated to four peak temperatures of $250^{\circ}C$, $300^{\circ}C$, $350^{\circ}C$, and $400^{\circ}C$, and then cooled to room temperature at cooling rates of $0.3^{\circ}C/min$ under three tensile hoop stresses of 80 MPa, 100 MPa, and 120 MPa. The cool-down specimens showed that high peak heat-up temperature led to lower hydrogen content and that larger tensile hoop stress generated larger radial hydride fraction and consequently lower plastic elongation. Based on these out-of-pile cladding tube test results only, it may be said that peak cladding temperature should be limited to a level < $250^{\circ}C$, regardless of the cladding hoop stress, to ensure cladding integrity during interim-dry storage and subsequent transport.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1133-1138
• /
• 2003

The pressure tubes, which contain high temperature heavy water and fuel, are within the core of a CANDU nuclear reactor, and are thus subjected to high stresses, temperature gradient, and neutron flux. Further, it is well known that pressure tubes of cold-worked Zr-2.5Nb materials result in hydrogen diffusion, which create fully-hydrided regions (frequently called Blister). Thus a proper investigation of hydrogen diffusion within zirconium-alloy nuclear components, such as CANDU pressure tube and fuel channels is essential to predict the structural integrity of these components. In this respect, this paper presents numerical investigation of hydrogen diffusion to quantify the hydrogen concentration for blister growth of CANDU pressure tube. For this purpose, coupled temperature-hydrogen diffusion analyses are performed by means of two-dimensional finite element analysis. Comparison of predicted temperature field and blister with published test data shows good agreement.

• 자원리싸이클링
• /
• 제21권5호
• /
• pp.18-30
• /
• 2012

Zr은 고온에서의 높은 치수안정성, 내식성은 물론 낮은 중성자 흡수단면적을 지녀 원자력산업용 소재 중 1차 방사능 차폐재인 핵연료 피복관으로 사용되며 현재까지 다른 소재로 대체 불가능하다. 하지만 Hf을 정제한 Zr sponge 제조기술은 미국, 프랑스, 러시아만 가지고 있어 원자력의존도가 높은 한국에서는 국가전략물자로 분류 철저히 관리되고 있다. 국내 유통되는 Zr의 대부분은 원자력산업에 사용되어 지며 유통구조는 정제된 Zr합금을 국외로부터 수입하여 tube로 가공 후 핵연료집합체로 제조되고, 그 외 소량이 합금첨가원소 및 폭약재 등 고부가가치 일반산업에 사용된다. 본 논문에서는 Zr 제조기술에 대한 현재산업현황 및 정련기술을 살펴보고, 최근 연구되고 있는 Electrolytic reduction process와 Molten oxide electrolysis와 같은 신 제련기술에 대한 소개 및 Zr recycling의 전반적인 기술소개도 포함하였다.

• 대한기계학회논문집A
• /
• 제24권1호
• /
• pp.206-214
• /
• 2000

The pressure tube is a major component of the CANDU reactor, which supports nuclear fuel bundle and it's containment vessel. If a flaw is found during the periodic inspection from the pressure tube s. the integrity evaluation must be carried out. and the safety requirements must be satisfied for continued service. In order to complete the integrity evaluation, complicated and iterative calculation procedures are required. Besides, a lot of data and knowledge for the evaluation are required for the entire: integrity evaluation process. For this reason. an integrity evaluation system, which provides efficient of evaluation with the help of attached databases, was developed. The developed system was built on the basis of ASME Sec. XI and FFSG(Fitness For Service Guidelines for zirconium alloy pressure tubes in operating CANDU reactors) issued by the AECL, and covers the delayed hydride cracking(DHC). This system does not only provide various databases including the 3-D finite element analysis results on pressure tubes, inspection data and design specifications but also is compatible with other commercial database software. In order to verify the developed system, several case studies have been performed and the results were compared with those from AECL. A good agreement was observed between those two results.

• 비파괴검사학회지
• /
• 제22권1호
• /
• pp.59-64
• /
• 2002

CANDU형 핵연료채널 압력관(Zr-2.5%Nb)과 calandria관(Zircaloy-2)에 대한 원격장 와전류탐상의 자계분포특성을 파악하기 위하여 유한요소 해석을 수행하였다. 압력관과 칼란드리아관의 전자기장 분포와 위상각 해석을 통하여 최적 검사 주파수와 감지코일의 위치를 평가하였다. 또한 축대칭 구조물(Al-ring과 Al-block)이 공존시 파라미터해석을 통하여 원격장 와전류의 특성을 평가하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 B
• /
• pp.690-692
• /
• 2001

A FEM model of the remote-field eddy current effect is presented for zirconium-2.5percent niobium(Zr-2.5%Nb) nuclear reactor pressure tubes to demonstrate the important electromagnetic field. Phenomena that describe this effect. This model is applied to evaluate the optimal operating frequency and detector position. There are many ambiguous experimental results connected with this technique. Finite element calculations can be used in the interpretation of these experimental results even though the electromagnetic fields measured in the remote-field technique are very small.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.441-444
• /
• 2000

The recycling process for reuse of uranium in the spent fuels consists various unit processes and the decladding process to extract the spent fuel pellet from the zirconium-based cladding is the beginning process of the recycling. There are two methods - mechanical and chemical - in the decladding process. In this paper, the mechanical decladding device by using a motor as a driving part and a press pin to separate the pellets from tube has been developed. This device was automated and modularized to make the remote operation and maintenance easy.

• Nuclear Engineering and Technology
• /
• 제30권3호
• /
• pp.202-211
• /
• 1998

Interfacial stresses at two-material interfaces and initial displacement field over the entire domain are obtained by modifying the potential energy functional with a penalty function, which enforces continuity of the stresses at the interface of two materials. Based on the initial displacement field and interfacial stresses, a new methodology to generate a continuous stress field over the entire domain has been proposed by combining the modified projection method of stress-smoothing and Loubignac's iterative method of improving the displacement field. Stress analysis is carried out on two examples made of dissimilar materials : one is a two-material cantilever composed of highly dissimilar materials and the other is a zirconium-lined cladding tube made of slightly dissimilar materials. Results of the analysis show that the proposed method provides an improved continuous stress field over the entire domain, and accurately predicts the nodal stresses at the interface, while the conventional displacement-based finite element method produces significant stress discontinuities at the interface. In addition, the total strain energy evaluated from the improved continuous stress field converges to the exact value in a few iterations.

• 자원리싸이클링
• /
• 제26권5호
• /
• pp.97-104
• /
• 2017

핵연료 피복관(지르코늄 합금)은 필거링, 세정, 산 세정 및 열처리공정을 거쳐 만든다. 튜브 표면의 산화층과 불순물을 제거하기 위하여 산 세정(酸 洗淨, Acid pickling) 공정이 요구된다. 이때 산세 공정 중 불산과 질산의 혼합 산(酸) 용액으로부터 용해된 Zr이 농축된 폐산은 중화반응을 거쳐 전량 폐기 처리 된다. 본 연구에서는 $BaF_2$ 침전 공정을 통해 재생산된 산세 용액의 잔존 불순물(Ba)이 산세에 미치는 영향을 관찰하였다. 이와 더불어 실제 핵연료 피복관의 산세 공정에 적합한 재생산 제조를 위한 잔존 Ba 및 Zr의 농도 저감 실험을 실시하여 최적 침전 공정 조건을 도출하였으며, 핵연료 피복관의 산세 공정을 모사한 파일럿 플랜트 산세공정 장치에서 재생산된 산세용액을 사용하여 피복관의 산세 효율을 AFM 분석을 통해 관찰하였다.

• Tribology and Lubricants
• /
• 제22권3호
• /
• pp.144-148
• /
• 2006

The experimental investigation was performed to find the associated changes in characteristics of fretting wear with various water temperatures. The fretting wear tests were carried out using the zirconium alloy tubes and the grids with increasing the water temperature. The tube materials in water of $20^{\circ}C,\;50^{\circ}C\;and\;80^{\circ}C$ were tested with the applied load of 20 N and the relative amplitude of $200{\mu}m$. The worn surfaces were observed by SEM, EDX analysis and 2D surface profiler. As the water temperature increased, the wear volume was decreased, but oxide layer was increased on the worn surface. The abrasive wear mechanism was observed at water temperature of $20^{\circ}C$ and adhesive wear mechanism occurred at water temperature of $50^{\circ}C,\;80^{\circ}C$. As the water temperature increased, surface micro-hardness was decreased, but wear depth and wear width were decreased due to increasing stick phenomenon. Stick regime occurred due to the formation of oxide layer on the worn surface with increasing water temperatures