• 한국재료학회지
• /
• 제8권9호
• /
• pp.783-790
• /
• 1998

용융점 및 물리.화학적 특성이 $\textrm{UO}_{2}$와 비슷한 yttria-stabilized-zirconia ($\textrm{ZrO}_{2}$-$\textrm{Y}_{2}\textrm{O}_{3}$)분말을 유도플라즈마(induction plasma)로 용융 침적시켜 원자력발전용 핵연료펠렛 제조공정에 응용하고자 하였다. 분말의 용융정도는 플라즈마동력 및 분말의 크기에 영향을 받는 것으로 나타났으며, 쉬스가스 조성, 분말분사관 위치, 입자크기 및 분사거리 등을 최적화 하여 Ar/$\textrm{H}_{2}$유량120/20$\ell$/min, 플리즈마 동력 80KW, 분사관의위치 8cm , 챔버압력 200Torr, 분사거리 18cm에서 이론밀도의 97.91%, 침적속도 20mm/min의 최적조건을 도출하였다. 침적시험에서 도출된 최적조건으로 펠렛몰더에서 제조한 펠렛은 96.5%의 밀도를 나타내었으며, 균일도 및 외곤도 우수하여 신기술에 의한 핵연료의 제조가능성을 확인하였다. 고밀도 침적에 영향을 미치는 각 변수들의 영향과 이들 변수들의 상호영향은 ANOVA(Analysis of Variance)을 이용하여 분석하였다.

• 한국공작기계학회논문집
• /
• 제15권5호
• /
• pp.91-96
• /
• 2006

The friction and wear properties of ceramics are very important in the applications to engineering ceramic parts such as seal rings, pump parts, automobile meter parts, and so on. In this study, the effects of each other purity on the mechanical and tribological properties of purity zirconia ceramics were investigated. Also in order to determine the effects of sliding distance, sliding speed, contact load, friction coefficient, the amount of worn out material at a certain time, and the prepared composites were measured. Crystalline phases and microstructure were examined with XRD and SEM. The results show that we obtained the good properties of friction coefficient and wear resistance at the purity 99.5% of zirconia. than this of the purity 95% were great at the wear amount of worn out material.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집E
• /
• pp.57-62
• /
• 2001

Korea Atomic Energy Research Institute (KAERI) launched an intermediate scale steam explosion experiment named Test for Real cOrium Interaction with water (TROI) using reactor material to investigate whether the corium would lead to energetic steam explosion when interacted with cold water at low pressure. The melt-water interaction is confined in a pressure vessel with the multi-dimensional fuel and water pool geometry. The cold crucible technology, where the mixture of powder in a water-cooled cage is heated by high frequency induction, is employed. In this paper, results of the first series of tests ($TROI-1{\sim}5$) were discussed. The ZrO2 jets with 5kg mass and 5cm diameter were poured into the 67cm deep water pool at $30{\sim}95^{\circ}C$. Either spontaneous steam explosions or quenching was observed. The morphology of debris and pressure wave profiles clearly indicates the each case.

• The Journal of Advanced Prosthodontics
• /
• 제14권6호
• /
• pp.346-359
• /
• 2022

PURPOSE. Four and six implant-supported fixed full-arch prostheses with various framework materials were assessed under different loading conditions. MATERIALS AND METHODS. In the edentulous maxilla, the implants were positioned in a configuration of four to six implant modalities. CoCr, Ti, ZrO₂, and PEEK materials were used to produce the prosthetic structure. Using finite element stress analysis, the first molar was subjected to a 200 N axial and 45° oblique force. Stresses were measured on the bone, implants, abutment screw, abutment, and prosthetic screw. The Von Mises, maximum, and minimum principal stress values were calculated and compared. RESULTS. The maximum and minimum principal stresses in bone were determined as CoCr < ZrO₂ < Ti < PEEK. The Von Mises stresses on the implant, implant screw, abutment, and prosthetic screws were determined as CoCr < ZrO₂ < Ti < PEEK. The highest Von Mises stress was 9584.4 Mpa in PEEK material on the prosthetic screw under 4 implant-oblique loading. The highest maximum principal stress value in bone was found to be 120.89 Mpa, for PEEK in 4 implant-oblique loading. CONCLUSION. For four and six implant-supported structures, and depending on the loading condition, the system accumulated different stresses. The distribution of stress was reduced in materials with a high elastic modulus. When choosing materials for implant-supported fixed prostheses, it is essential to consider both the number of implants and the mechanical and physical attributes of the framework material.

• Bulletin of the Korean Chemical Society
• /
• 제31권2호
• /
• pp.397-400
• /
• 2010

Zirconium oxide thin films deposited on the p-type Si(100) substrates by radio-frequency (RF) reactive magnetron sputtering with different plasma gas ratios have been studied by using spectroscopic ellipsometry (SE), atomic force microscopy (AFM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). The deposition of the films was monitored by the oxygen gas ratio which has been increased from 0 to 80%. We found that the thickness and roughness of the zirconium oxide thin films are relatively constant. The XRD revealed that the deposited thin films have polycrystalline phases, Zr(101) and monoclinic $ZrO_2$ ($\bar{1}31$). The XPS result showed that the oxidation states of zirconium suboxides were changed to zirconia form with increasing $O_2$ gas ratio.

• 한국세라믹학회지
• /
• 제42권9호
• /
• pp.637-644
• /
• 2005

In order to find a proper buffering material which can prohibit an unwanted interfacial reaction between anode and electrolyte of LSGM-based SOFC, we examined a gadolinium doped ceria and scandium doped zirconia as a candidate. For this examination, we investigated the microstructural and phase stability of the interface under different buffering layer conditions. According to the investigation, ceria based material induced a serious La diffusion out of the LSGM electrolyte resulted in the formation of very resistive $LaSrGa_3O_7$ phase at the interface. On the other hand zirconia based material was directly reacted with LSGM electrolyte and thus produced very resistive reaction products such as $La_2Zr_2O_7,\;Sr_2ZrO_4,\;LaSrGaO_4\;and\;LaSrGa_3O_7$. From this study we found that an improper buffering material induced the higher internal cell resistance rather than an interfacial stability.

• 한국결정성장학회지
• /
• 제8권2호
• /
• pp.356-364
• /
• 1998

$ZTA:\;Al_2O_3/\;15\;vol{%}\;ZrO_2$ (Zirconia Toughened Alumina : ZTA)를 상압소결에 의해 제조시 분무건조한 granule의 특성에 따른 성형밀도 및 소결밀도의 변화를 고찰하여, 소결밀도의 재현성을 향상시킬 수 있는 성령 공정 조건을 제시하였다. 결합제의 첨가 유무에 따라 granule의 구형도, 평균크기, granule 내의 hollow의 생성정도, 수분함유량 등이 다름을 확인하였다. granule의 물성 차이가 성형거동에 미치는 영향을 성형압(80~120MPa)과 성형방법(일축성형과 정수압 성형)에 따른 성형밀도의 변화를 통하여 조사하였다. granule의 특성 변화에 의한 밀도의 낮은 재현성은 성형압과 성형방법의 최적화를 통하여 극복될 수 있음을 확인하였다. 즉 가능한 낮은 압력(80MPa)에서 일축성형한 후 고압(500MPa)에서 정수압 성형하였을 때 소결후 밀도변화는 1%이내에서 조절되었다.

• 한국세라믹학회지
• /
• 제51권6호
• /
• pp.598-604
• /
• 2014

Considerable research efforts have been explored attempting to enhance the thermal durability of thermal barrier coatings (TBCs) at the high operating temperatures of gas turbines. In this study, the suspension plasma spray (SPS) process was applied to produce TBCs with a segmented structure by using an yttria-stabilized zirconia (YSZ) suspension. Four different experiment sets were carried out by controlling the ratio between surface roughness of the bond coat and feed stock size ($R_a/D_{50}$) in order to examine the effect of $R_a/D_{50}$ ratio on the microstructure of SPS-prepared coatings. When the $R_a/D_{50}$ had a high value of 11.8, a deposited thick coating turned out to have a cone-type columnar microstructure. In contrast, at the low $R_a/D_{50}$ values of 2.9 and 0.18, a deposited thick coating appeared to have a dense, vertically-cracked microstructure. However, with the very low $R_a/D_{50}$ value of 0.05 the coating was delaminated.

• 한국세라믹학회지
• /
• 제21권3호
• /
• pp.239-244
• /
• 1984

The effect of tetragonal $ZrO_2$ phase on the mechanical behavior in 7 mole% calcia partially stabilized zirconia has been studied. The $ZrO_2$ powder containg 7 mole% CaO prepared by Hot Petroleum Drying Method calcined at 80$0^{\circ}C$ for 1 hour was nearly 100% tetragonal but as the calcining temperature increased certain amount of monoclinic phase appeared. The sintered specimen at 1$700^{\circ}C$ for 5 hours was aged at 130$0^{\circ}C$ for 0, 24, 48, 72 hours. X-ray diffraction data showed that in the aged specimen monoclinic tetragonal and cubic phase coexisted. The Kc value of aged specimen for 48 hr was about 4.5MN/m3/2 much greater than unaged sample. But aged for 72 hr the KiC value was decreased. The increasing of toughness in PSZ is based on the Stress-Induced Phase Transformation that is metastable tetra-gonal $ZrO_2$ changes t stable monoclinic phase within the stress field of crack and the mechanical fracture energy absorption is occured But in this case due to certain amount of tetragonal phase transformed to monoclinic phase during cooling the microcrack effect by transformation also considered. Trerefore both Stress-Induced Phase Transformation and inclusion induced microcracking effect contrbute to the increase of fracture toughness of 7 mole% CaO-$ZrO_2$ containing monoclinic and tetragnola phase simulataneously.

• 한국세라믹학회지
• /
• 제28권8호
• /
• pp.654-660
• /
• 1991

Stabilized Zirconia (3 mol % Yttria, 3Y-TZP) was joined with intermetallic compound NiTi which has similar thermal expansion coefficient. The optimum bonding condition was determined by the Taguchi Method. Under the optimum bonding condition, the 4-point bending strength was as high as 400 MPa. bonding interfaces were examined by optical microscope, SEM, and TEM; reaction products were identified by XRD and TEM, The relationship between products and strength was examined.